Zhoujian An
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhoujian An has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
Dong Zhang
School of Energy and Power Engineering
20 shared publications- Xiaoze Du
Key Laboratory of Power Station Energy Transfer Conversion and System, North China Electric Power University, Ministry of Education, Beijing 102206, China
10 shared publications Xiaoze Du
9 shared publicationsYong Ding
School of Aerospace Engineering
8 shared publicationsJian Fu
School of Energy and Power Engineering
7 shared publicationsHamir Johan Mombeki Pea
6 shared publications
Latest Publications
- Open Access
Comparative Study on Thermal Insulation Performance of the Various Materials for Suppressing Thermal Runaway Propagation in Lithium-Ion Battery Modules
The thermal runaway propagation in lithium-ion battery modules poses a serious threat to the safety of electric vehicles and energy storage systems. This study experimentally evaluated the thermal propagation suppression performance of five insulating materials: polyimide foam, nano-porous silica aerogel, ceramic fiber, pre-oxidized fiber aerogel, and mica sheet on 4 Ah ternary pouch cell modules. Thermal runaway was triggered in Cell 1 via an external short circuit (30C), and propagation behavior was characterized in terms of temperature evolution, propagation time, mass loss, and microstructural analysis. The results indicated that aerogel-based materials exhibited excellent thermal insulation performance. For the nano-porous silica aerogel, the temperature difference between its front and back surfaces reached as high as 484 °C, while the temperature rise of the adjacent cell was kept below 107 °C, thereby completely blocking propagation. The module mass loss was only 17.63 g, corresponding to a material loss rate of 0.67%. Pre-oxidized fiber aerogel also effectively suppressed propagation, albeit with a slightly higher material loss rate of 2.20%. In contrast, ceramic fiber and mica sheets only partially delayed thermal runaway propagation, as the adjacent cells still exhibited cracking and electrolyte leakage. Polyimide foam failed to prevent thermal runaway propagation, only extending the total propagation time from 424 s to 678 s (an increase of 60%) before being completely burned. Microstructural SEM analysis revealed that the aerogel materials suffered only slight fiber fracture, whereas the ceramic fiber underwent severe structural damage, the mica sheets displayed cracks and melting, and the polyimide foam was completely combusted. Taken together, these findings suggest that nano-porous silica aerogel is the preferred material for blocking thermal runaway in lithium-ion batteries, offering practical guidance for the thermal safety design of battery systems.
Open AccessComparative Study on Thermal Insulation Performance of the Various Materials for Suppressing Thermal Runaway Propagation in Lithium-Ion Battery Modules
The thermal runaway propagation in lithium-ion battery modules poses a serious threat to the safety of electric vehicles and energy storage systems. This study experimentally evaluated the thermal propagation suppression performance of five insulating materials: polyimide foam, nano-porous silica aerogel, ceramic fiber, pre-oxidized fiber aerogel, and mica sheet on 4 Ah ternary pouch cell modules. Thermal runaway was triggered in Cell 1 via an external short circuit (30C), and propagation behavior was characterized in terms of temperature evolution, propagation time, mass loss, and microstructural analysis. The results indicated that aerogel-based materials exhibited excellent thermal insulation performance. For the nano-porous silica aerogel, the temperature difference between its front and back surfaces reached as high as 484 °C, while the temperature rise of the adjacent cell was kept below 107 °C, thereby completely blocking propagation. The module mass loss was only 17.63 g, corresponding to a material loss rate of 0.67%. Pre-oxidized fiber aerogel also effectively suppressed propagation, albeit with a slightly higher material loss rate of 2.20%. In contrast, ceramic fiber and mica sheets only partially delayed thermal runaway propagation, as the adjacent cells still exhibited cracking and electrolyte leakage. Polyimide foam failed to prevent thermal runaway propagation, only extending the total propagation time from 424 s to 678 s (an increase of 60%) before being completely burned. Microstructural SEM analysis revealed that the aerogel materials suffered only slight fiber fracture, whereas the ceramic fiber underwent severe structural damage, the mica sheets displayed cracks and melting, and the polyimide foam was completely combusted. Taken together, these findings suggest that nano-porous silica aerogel is the preferred material for blocking thermal runaway in lithium-ion batteries, offering practical guidance for the thermal safety design of battery systems.
- Open Access
Multi-Parameter Analysis of PCM-Based Thermal Management Performance and Thermophysical Characteristics of Lithium-Ion Battery Packs
A three-dimensional structural model of a cylindrical lithium-ion battery pack incorporating composite phase change material (PCM) is developed in this study, and numerical simulations are conducted using CFD software to investigate the heat dissipation characteristics of the battery pack. The results show that the composite PCM effectively suppresses the temperature rise within the battery pack, maintaining both the temperature and the temperature difference in the battery pack within acceptable ranges. Parameter analysis reveals that increasing the radial thermal conductivity of the battery reduces the heating rate and improves the temperature uniformity of the overall system. Within the investigated parameter range, increasing the thermal conductivity of the composite PCM beyond approximately 1 W/(m·K) results in a region of diminishing improvement in thermal performance. Beyond this range, further increases in thermal conductivity result in only marginal reductions in the maximum temperature, indicating that excessive enhancement of thermal conductivity provides limited thermal benefits and should be balanced with latent heat capacity. An increase in the latent heat of the composite PCM lowers both the maximum temperature and the maximum temperature difference at the end of discharge, thereby enhancing system temperature uniformity. Conversely, enlarging the external air convection heat transfer coefficient yields a limited cooling effect while deteriorating the temperature uniformity within the system. Therefore, on the principle of fully utilizing latent heat and minimizing energy consumption, the external convection heat transfer coefficient should be set as low as possible. This study provides theoretical guidance for the parametric design of PCM-based thermal management systems.
Open AccessMulti-Parameter Analysis of PCM-Based Thermal Management Performance and Thermophysical Characteristics of Lithium-Ion Battery Packs
A three-dimensional structural model of a cylindrical lithium-ion battery pack incorporating composite phase change material (PCM) is developed in this study, and numerical simulations are conducted using CFD software to investigate the heat dissipation characteristics of the battery pack. The results show that the composite PCM effectively suppresses the temperature rise within the battery pack, maintaining both the temperature and the temperature difference in the battery pack within acceptable ranges. Parameter analysis reveals that increasing the radial thermal conductivity of the battery reduces the heating rate and improves the temperature uniformity of the overall system. Within the investigated parameter range, increasing the thermal conductivity of the composite PCM beyond approximately 1 W/(m·K) results in a region of diminishing improvement in thermal performance. Beyond this range, further increases in thermal conductivity result in only marginal reductions in the maximum temperature, indicating that excessive enhancement of thermal conductivity provides limited thermal benefits and should be balanced with latent heat capacity. An increase in the latent heat of the composite PCM lowers both the maximum temperature and the maximum temperature difference at the end of discharge, thereby enhancing system temperature uniformity. Conversely, enlarging the external air convection heat transfer coefficient yields a limited cooling effect while deteriorating the temperature uniformity within the system. Therefore, on the principle of fully utilizing latent heat and minimizing energy consumption, the external convection heat transfer coefficient should be set as low as possible. This study provides theoretical guidance for the parametric design of PCM-based thermal management systems.
- Open Access
- 1 July 2026
- Published by Elsevier in SSRN Electronic Journal
Early-stage suppression of external-short-circuit-induced thermal runaway in lithium-ion batteries using low-pressure water mist
External short circuits (ESCs) in lithium-ion batteries are often abrupt and difficult to predict in advance; therefore, rapid suppression at the early stage of ESC abuse is essential for preventing its escalation into thermal runaway and mitigate the resulting hazards. Low-pressure water mist provides a promising approach for cooling and heat-removal capability; however, its early-stage suppression behavior and parameter-dependent mechanisms under ESC conditions remain insufficiently understood. In this study, the effects of water mist flow rate, spray application surface, and intervention timing on the early-stage suppression of external-short-circuit-induced thermal runaway were experimentally investigated. The suppression behavior was further analyzed by considering the coupling between water mist deposition, evaporative cooling, and battery heat-accumulation regions. The results show that the suppression performance of water mist strongly depends on the matching between atomization conditions and the targeted battery surface. Under appropriate flow-rate and spray-surface configurations, water mist effectively prevented open flame and severe casing damage, and remained effective during the high-temperature pre-runaway stage. Propagation tests further demonstrated that water mist can delay or inhibit cell-to-cell thermal runaway propagation. These findings provide a practical basis for rapid early-stage mitigation of ESC-induced thermal runaway in lithium-ion batteries.
- 1 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEarly-stage suppression of external-short-circuit-induced thermal runaway in lithium-ion batteries using low-pressure water mist
External short circuits (ESCs) in lithium-ion batteries are often abrupt and difficult to predict in advance; therefore, rapid suppression at the early stage of ESC abuse is essential for preventing its escalation into thermal runaway and mitigate the resulting hazards. Low-pressure water mist provides a promising approach for cooling and heat-removal capability; however, its early-stage suppression behavior and parameter-dependent mechanisms under ESC conditions remain insufficiently understood. In this study, the effects of water mist flow rate, spray application surface, and intervention timing on the early-stage suppression of external-short-circuit-induced thermal runaway were experimentally investigated. The suppression behavior was further analyzed by considering the coupling between water mist deposition, evaporative cooling, and battery heat-accumulation regions. The results show that the suppression performance of water mist strongly depends on the matching between atomization conditions and the targeted battery surface. Under appropriate flow-rate and spray-surface configurations, water mist effectively prevented open flame and severe casing damage, and remained effective during the high-temperature pre-runaway stage. Propagation tests further demonstrated that water mist can delay or inhibit cell-to-cell thermal runaway propagation. These findings provide a practical basis for rapid early-stage mitigation of ESC-induced thermal runaway in lithium-ion batteries.
- Open Access
Study on the Thermal Runaway Mechanism of Lithium-Ion Batteries Induced by External Short Circuit Under Mechanical Stress State
The pouch cells are typically assembled into modules with mechanical preload to meet voltage/capacity requirements, and the stress state is a critical factor influencing the failure behavior of lithium-ion batteries during external short circuits. This study comparatively analyzes performance differences between mechanically preloaded and unconstrained batteries during external short circuits, quantitatively investigating dynamic trends and safety boundaries of electro-thermo-mechanical signals during short circuits in fully charged (100% SOC) batteries across preloads of 500~3500 N. Key findings indicate that under the 50C external short-circuit (ESC) condition, mechanical constraint significantly reduces the central peak temperature of the 100% SOC battery, with a measured reduction of 31.6 °C. Moreover, constrained cells exhibit well-defined lamellar graphite structures, unlike the surface cracking observed in unconstrained anodes, confirming enhanced safety. Rupture temperatures consistently ranged between 112.00 and 124.00 °C across all conditions, with stable temperature rise rates (~0.5 °C·s−1) during short circuits indicating minimal preload impact on heat generation, though excessively high or low preloads accelerated physical damage. Further SOC investigations (10%~100%) demonstrate that lower SOC increases temperature rise rates due to polarization-induced resistance rise, resulting in shorter discharge durations with lower peak temperatures/swelling forces without leakage, while high-SOC cells exhibit prolonged discharge, yielding higher peak temperatures/swelling forces at rupture. This study provides critical insights for enhancing process safety in lithium battery energy storage systems. These findings collectively guide safer battery pack design, module constraint strategies and emergency response protocols to reduce cascading failure risks in stationary energy storage applications.
Open AccessStudy on the Thermal Runaway Mechanism of Lithium-Ion Batteries Induced by External Short Circuit Under Mechanical Stress State
The pouch cells are typically assembled into modules with mechanical preload to meet voltage/capacity requirements, and the stress state is a critical factor influencing the failure behavior of lithium-ion batteries during external short circuits. This study comparatively analyzes performance differences between mechanically preloaded and unconstrained batteries during external short circuits, quantitatively investigating dynamic trends and safety boundaries of electro-thermo-mechanical signals during short circuits in fully charged (100% SOC) batteries across preloads of 500~3500 N. Key findings indicate that under the 50C external short-circuit (ESC) condition, mechanical constraint significantly reduces the central peak temperature of the 100% SOC battery, with a measured reduction of 31.6 °C. Moreover, constrained cells exhibit well-defined lamellar graphite structures, unlike the surface cracking observed in unconstrained anodes, confirming enhanced safety. Rupture temperatures consistently ranged between 112.00 and 124.00 °C across all conditions, with stable temperature rise rates (~0.5 °C·s−1) during short circuits indicating minimal preload impact on heat generation, though excessively high or low preloads accelerated physical damage. Further SOC investigations (10%~100%) demonstrate that lower SOC increases temperature rise rates due to polarization-induced resistance rise, resulting in shorter discharge durations with lower peak temperatures/swelling forces without leakage, while high-SOC cells exhibit prolonged discharge, yielding higher peak temperatures/swelling forces at rupture. This study provides critical insights for enhancing process safety in lithium battery energy storage systems. These findings collectively guide safer battery pack design, module constraint strategies and emergency response protocols to reduce cascading failure risks in stationary energy storage applications.
- Open Access
Research on the Characteristics of Internal Short Circuits in Lithium-Ion Batteries Under Complex Condition: Nail Penetration Coupled with Charge/Discharge
This study systematically investigates the internal short circuit (ISC) characteristics of lithium-ion batteries (LIBs) for electric vehicles under nail penetration abuse coupled with charge/discharge operations. By establishing a nail penetration coupled with dynamic charge/discharge experimental platform and using commercial NCM pouch cells as test subjects, it comprehensively analyzes the effects of different charge/discharge operations (charging, discharging, resting) and C-rates (0.2 C–3 C) on battery surface temperature, voltage, current, mass loss, and thermal runaway behavior. The research finds that a mutual inhibitory effect exists between discharge operation and ISC, manifested as reduced discharge current along with decreased surge current, temperature rise rate, and voltage drop, significantly lowering the battery’s thermal runaway risk. In contrast, charging operation exacerbates ISC severity, causing increases in surge current, temperature rise rate, maximum temperature, and mass loss with higher C-rates, substantially enhancing thermal hazards. The study further reveals the underlying mechanisms: during discharge, a “Li+ competition” effect suppresses the short-circuit current, whereas during charging, the external power source and the battery jointly form the short-circuit current, intensifying heat generation. This research provides important experimental evidence and theoretical support for the thermal safety design and risk assessment of LIBs under operating conditions.
Open AccessResearch on the Characteristics of Internal Short Circuits in Lithium-Ion Batteries Under Complex Condition: Nail Penetration Coupled with Charge/Discharge
This study systematically investigates the internal short circuit (ISC) characteristics of lithium-ion batteries (LIBs) for electric vehicles under nail penetration abuse coupled with charge/discharge operations. By establishing a nail penetration coupled with dynamic charge/discharge experimental platform and using commercial NCM pouch cells as test subjects, it comprehensively analyzes the effects of different charge/discharge operations (charging, discharging, resting) and C-rates (0.2 C–3 C) on battery surface temperature, voltage, current, mass loss, and thermal runaway behavior. The research finds that a mutual inhibitory effect exists between discharge operation and ISC, manifested as reduced discharge current along with decreased surge current, temperature rise rate, and voltage drop, significantly lowering the battery’s thermal runaway risk. In contrast, charging operation exacerbates ISC severity, causing increases in surge current, temperature rise rate, maximum temperature, and mass loss with higher C-rates, substantially enhancing thermal hazards. The study further reveals the underlying mechanisms: during discharge, a “Li+ competition” effect suppresses the short-circuit current, whereas during charging, the external power source and the battery jointly form the short-circuit current, intensifying heat generation. This research provides important experimental evidence and theoretical support for the thermal safety design and risk assessment of LIBs under operating conditions.
- 8 April 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (15) , 10681-10694
Research on the Photothermal Conversion and Water Collection Performance of MOF-303 Composites for Solar-Driven Air Water Harvesting
Atmospheric water harvesting is a promising solution to freshwater shortage because it is not limited by location. Metal–organic frameworks (MOFs) have attracted much attention for low-humidity applications due to their large surface areas and strong water adsorption capacities. In this study, the desorption efficiency of MOF-based adsorbents under solar heating was improved by adding efficient photothermal materials. MOF-303 was combined with Fe3O4, MWCNTs, and Ti3C2 by ball milling. Characterization analysis of the composite materials’ morphology, elemental distribution, crystal structure, and functional group changes demonstrated that the composite formation was successful. The results showed that compared to the original MOF-303, adding 10 wt % photothermal material greatly improved light absorption, leading to faster solar heating and quicker water desorption. However, the introduction of photothermal materials leads to a reduction in the effective adsorption sites within the composite materials, resulting in lower saturated water absorption capacities for all three composites compared to the original MOF-303. Among the three composite materials, Ti3C2/MOF-303 shows the best overall performance. Under 40% RH conditions, the material increased water vapor adsorption from 0 g/g to 0.382 g/g within 30 min. After 20 min of irradiation at 1 sun, the surface temperature of the material rapidly rose to 87.4 °C, reducing the remaining water content to 11.3%. Under the same conditions, the original MOF-303 had a water vapor adsorption of 0.42 g/g, a surface temperature of 59.8 °C after irradiation, and a remaining water content of about 31.7%. Taking 30% RH as an example, the Ti3C2/MOF-303 water vapor adsorption capacity is about 8.1% lower than that of the original MOF-303. During desorption at 85 °C, it takes approximately 20 min to achieve complete desorption, which is 20% shorter than that of the original MOF-303.
- 8 April 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (15) , 10681-10694
Research on the Photothermal Conversion and Water Collection Performance of MOF-303 Composites for Solar-Driven Air Water Harvesting
Atmospheric water harvesting is a promising solution to freshwater shortage because it is not limited by location. Metal–organic frameworks (MOFs) have attracted much attention for low-humidity applications due to their large surface areas and strong water adsorption capacities. In this study, the desorption efficiency of MOF-based adsorbents under solar heating was improved by adding efficient photothermal materials. MOF-303 was combined with Fe3O4, MWCNTs, and Ti3C2 by ball milling. Characterization analysis of the composite materials’ morphology, elemental distribution, crystal structure, and functional group changes demonstrated that the composite formation was successful. The results showed that compared to the original MOF-303, adding 10 wt % photothermal material greatly improved light absorption, leading to faster solar heating and quicker water desorption. However, the introduction of photothermal materials leads to a reduction in the effective adsorption sites within the composite materials, resulting in lower saturated water absorption capacities for all three composites compared to the original MOF-303. Among the three composite materials, Ti3C2/MOF-303 shows the best overall performance. Under 40% RH conditions, the material increased water vapor adsorption from 0 g/g to 0.382 g/g within 30 min. After 20 min of irradiation at 1 sun, the surface temperature of the material rapidly rose to 87.4 °C, reducing the remaining water content to 11.3%. Under the same conditions, the original MOF-303 had a water vapor adsorption of 0.42 g/g, a surface temperature of 59.8 °C after irradiation, and a remaining water content of about 31.7%. Taking 30% RH as an example, the Ti3C2/MOF-303 water vapor adsorption capacity is about 8.1% lower than that of the original MOF-303. During desorption at 85 °C, it takes approximately 20 min to achieve complete desorption, which is 20% shorter than that of the original MOF-303.
- 2 March 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (7) , 5617-5632
Improvement of carbonate thermophysical properties by high-temperature melting: a fluid used for heat transfer in high-temperature CSP device
- 2 March 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (7) , 5617-5632
Improvement of carbonate thermophysical properties by high-temperature melting: a fluid used for heat transfer in high-temperature CSP device
- Open Access
- 3 February 2026
- Published by Elsevier in SSRN Electronic Journal
Optimization design and analysis of precooler for SCO2 Brayton cycle based on multi-objective genetic algorithm
The Supercritical carbon dioxide Brayton cycle (SCBC) is a promising technology for renewable thermal power generation, known for its compact layout and high thermodynamic efficiency. In the SCBC, the recuperator, heater, and precooler are typically realized using printed circuit heat exchangers (PCHEs). While most current research focuses on the recuperator and heater, research focusing on the precooler remains relatively limited. The impact of precooler design on cycle efficiency has not yet been fully explored. To address this research gap, the optimal design of the precooler in the SCBC is investigated through a multi-objective genetic algorithm in present study. The design procedure first examines the effects of individual boundary conditions and geometric parameters on precooler performance. Subsequently, a multi-objective optimization is performed using the Non-dominated Sorting Genetic Algorithm II (NSGA-II), with cycle thermal efficiency, entropy generation, and total cost are selected as the optimization objectives. Finally, based on a trade-off analysis of the Pareto frontier, the optimal design point is identified. The three objective values corresponding to the final design point are 0.53, 3.07×10-4, and 38.80, respectively. The findings provide a reference design point for the precooler in SCBC, established through a holistic consideration of cycle efficiency, irreversibility, and economic performance.
- 3 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessOptimization design and analysis of precooler for SCO2 Brayton cycle based on multi-objective genetic algorithm
The Supercritical carbon dioxide Brayton cycle (SCBC) is a promising technology for renewable thermal power generation, known for its compact layout and high thermodynamic efficiency. In the SCBC, the recuperator, heater, and precooler are typically realized using printed circuit heat exchangers (PCHEs). While most current research focuses on the recuperator and heater, research focusing on the precooler remains relatively limited. The impact of precooler design on cycle efficiency has not yet been fully explored. To address this research gap, the optimal design of the precooler in the SCBC is investigated through a multi-objective genetic algorithm in present study. The design procedure first examines the effects of individual boundary conditions and geometric parameters on precooler performance. Subsequently, a multi-objective optimization is performed using the Non-dominated Sorting Genetic Algorithm II (NSGA-II), with cycle thermal efficiency, entropy generation, and total cost are selected as the optimization objectives. Finally, based on a trade-off analysis of the Pareto frontier, the optimal design point is identified. The three objective values corresponding to the final design point are 0.53, 3.07×10-4, and 38.80, respectively. The findings provide a reference design point for the precooler in SCBC, established through a holistic consideration of cycle efficiency, irreversibility, and economic performance.