Yusuke Kumazaki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yusuke Kumazaki has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Naoki Hara
Fujitsu Ltd., Atsugi, Kanagawa, Japan
5 shared publications- Naoya Okamoto
Fujitsu Ltd., Atsugi, Japan
4 shared publications Toshihiro Ohki
Fujitsu Ltd., Atsugi, Japan
4 shared publicationsShiro Ozaki
Fujitsu Ltd., Atsugi, Japan
3 shared publicationsYasuhiro Nakasha
Fujitsu Ltd., Atsugi, Japan
3 shared publications- Atsushi Yamada
Fujitsu Laboratories, Japan
2 shared publications
Latest Publications
- 21 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (3) , 358-361
37.1-dBm W-Band Power Amplifier Module Using GaN-Based HEMTs Stabilized With Resistive Back Metal for Broadband Wireless Applications
This letter presents a four-way W-band power amplifier (PA) module that packages GaN-based high electron mobility transistor (HEMT) millimeter-wave monolithic integrated circuits (MMICs) designed with coplanar waveguides (CPWs). A resistive-back-metal (RBM) layer was formed on the back side of the MMICs to keep stable in the module even without using substrate vias. The verification of the effect of the RBM layer was performed using CPW-based MMIC test chips. The assembled PA module, where millimeter-wave components, such as a waveguide (WG) combiner/divider and a WG-to-microstrip line transition, were optimized to reduce losses and flatten frequency responses, demonstrated stable and broadband characteristics in a frequency range of 88–100 GHz. A peak output power (POUT) of 37.1 dBm with a power-added efficiency (PAE) of 9.9% was achieved at a frequency of 92 GHz and a bias voltage (VDS) of 15 V. VDS was set to 20 V to enhance the power performance of the PA module, achieving a peak POUT of 38.8 dBm with a PAE of 8.1%. To the best of our knowledge, the PA module exhibited the highest peak POUT value among W-band single PA modules with a bandwidth (BW) of more than 10 GHz.
- 21 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (3) , 358-361
37.1-dBm W-Band Power Amplifier Module Using GaN-Based HEMTs Stabilized With Resistive Back Metal for Broadband Wireless Applications
This letter presents a four-way W-band power amplifier (PA) module that packages GaN-based high electron mobility transistor (HEMT) millimeter-wave monolithic integrated circuits (MMICs) designed with coplanar waveguides (CPWs). A resistive-back-metal (RBM) layer was formed on the back side of the MMICs to keep stable in the module even without using substrate vias. The verification of the effect of the RBM layer was performed using CPW-based MMIC test chips. The assembled PA module, where millimeter-wave components, such as a waveguide (WG) combiner/divider and a WG-to-microstrip line transition, were optimized to reduce losses and flatten frequency responses, demonstrated stable and broadband characteristics in a frequency range of 88–100 GHz. A peak output power (POUT) of 37.1 dBm with a power-added efficiency (PAE) of 9.9% was achieved at a frequency of 92 GHz and a bias voltage (VDS) of 15 V. VDS was set to 20 V to enhance the power performance of the PA module, achieving a peak POUT of 38.8 dBm with a PAE of 8.1%. To the best of our knowledge, the PA module exhibited the highest peak POUT value among W-band single PA modules with a bandwidth (BW) of more than 10 GHz.
- Open Access
- 18 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 12, 965-973
High Output Power and Efficiency 300-GHz Band InP-Based MOS-HEMT Power Amplifiers With Composite-Channel and Double-Side Doping
This paper demonstrated high-output-power and high-efficiency power amplifier (PA) monolithic microwave-integrated circuit (MMIC) at 300-GHz band (252-296 GHz) with the use of InP-based metal-oxide-semiconductor high-electron-mobility transistors (HEMTs) with composite-channel (CC) and double-side-doping (DD) techniques. The CC-DD structure obtained high output current and low channel resistance due to the improved carrier density and mobility. W-band load-pull measurement revealed the drastically improved output power density of CC-DD structure compared with that of single-channel DD structure. The 2-stage cascaded, 4-way, and 16-way PA-MMICs were designed based on stacked common-gate transistors with current reuse topology. The cascaded PA-MMIC exhibited a power-added efficiency (PAE) of 7.8%, and the 16-way PA-MMIC exhibited an output power of 16.9 dBm. These values are the highest among all the values reported for the 300-GHz band PA-MMICs. The 4-way PA-MMIC achieved a high output power of 13.6-14.6 dBm and high PAE of 4.8%-6.3% simultaneously at the entire 300-GHz band.
- 18 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 12, 965-973
Open AccessHigh Output Power and Efficiency 300-GHz Band InP-Based MOS-HEMT Power Amplifiers With Composite-Channel and Double-Side Doping
This paper demonstrated high-output-power and high-efficiency power amplifier (PA) monolithic microwave-integrated circuit (MMIC) at 300-GHz band (252-296 GHz) with the use of InP-based metal-oxide-semiconductor high-electron-mobility transistors (HEMTs) with composite-channel (CC) and double-side-doping (DD) techniques. The CC-DD structure obtained high output current and low channel resistance due to the improved carrier density and mobility. W-band load-pull measurement revealed the drastically improved output power density of CC-DD structure compared with that of single-channel DD structure. The 2-stage cascaded, 4-way, and 16-way PA-MMICs were designed based on stacked common-gate transistors with current reuse topology. The cascaded PA-MMIC exhibited a power-added efficiency (PAE) of 7.8%, and the 16-way PA-MMIC exhibited an output power of 16.9 dBm. These values are the highest among all the values reported for the 300-GHz band PA-MMICs. The 4-way PA-MMIC achieved a high output power of 13.6-14.6 dBm and high PAE of 4.8%-6.3% simultaneously at the entire 300-GHz band.
- Open Access
- 1 August 2024
- Published by IOP Publishing in Applied Physics Express
- Vol. 17 (8) , 086504
High-power and efficiency W-band InAlGaN/AlN/GaN high-electron-mobility transistors for future high-capacity wireless communications
This study describes high-power and high-efficiency W-band InAlGaN/AlN/GaN high-electron-mobility transistors (HEMTs) for future sub-terahertz wireless communications. A low-thermal-budget selective-area growth (SAG) process was developed to obtain low contact resistance with low trap states. Transmission lines and substrate structures were optimized to obtain high-thermal conductivity and low substrate resonance. Consequently, a high output power of 28.7 dBm (742 mW), output power density of 4.6 W mm−1, and power-added efficiency (PAE) of 28.0% were achieved with pre-matched InAlGaN/AlN/GaN HEMTs at 90 GHz, which were superior combination of output power and PAE compared to the conventional high-temperature SAG process.
- 1 August 2024
- Published by IOP Publishing in Applied Physics Express
- Vol. 17 (8) , 086504
Open AccessHigh-power and efficiency W-band InAlGaN/AlN/GaN high-electron-mobility transistors for future high-capacity wireless communications
This study describes high-power and high-efficiency W-band InAlGaN/AlN/GaN high-electron-mobility transistors (HEMTs) for future sub-terahertz wireless communications. A low-thermal-budget selective-area growth (SAG) process was developed to obtain low contact resistance with low trap states. Transmission lines and substrate structures were optimized to obtain high-thermal conductivity and low substrate resonance. Consequently, a high output power of 28.7 dBm (742 mW), output power density of 4.6 W mm−1, and power-added efficiency (PAE) of 28.0% were achieved with pre-matched InAlGaN/AlN/GaN HEMTs at 90 GHz, which were superior combination of output power and PAE compared to the conventional high-temperature SAG process.
- 1 November 2023
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Transactions on Electronics
- Vol. E106.C (11) , 661-668
High-Efficiency 250-320GHz Power Amplifiers Using InP-Based Metal-Oxide-Semiconductor High-Electron-Mobility Transistors
This work shows a broadband, high-efficiency power amplifier (PA) monolithic microwave integrated circuit (MMIC) that uses InP-based metal-oxide-semiconductor (MOS) high-electron-mobility transistors (HEMTs) with an extended drain-side access region and broadband conjugate matching topology. Advanced device technologies, namely, double-side-doped structures, MOS gate structures, and asymmetric gate recess, were adopted, and the length of the drain-side access region was optimized to simultaneously obtain high power and efficiency. A common-source PA MMIC based on InP-based MOS-HEMTs was fabricated, and an interstage circuit was designed to maximize the S21 per unit stage in the broadband, resulting in a record-high power-added efficiency and wide bandwidth.
- 1 November 2023
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Transactions on Electronics
- Vol. E106.C (11) , 661-668
High-Efficiency 250-320GHz Power Amplifiers Using InP-Based Metal-Oxide-Semiconductor High-Electron-Mobility Transistors
This work shows a broadband, high-efficiency power amplifier (PA) monolithic microwave integrated circuit (MMIC) that uses InP-based metal-oxide-semiconductor (MOS) high-electron-mobility transistors (HEMTs) with an extended drain-side access region and broadband conjugate matching topology. Advanced device technologies, namely, double-side-doped structures, MOS gate structures, and asymmetric gate recess, were adopted, and the length of the drain-side access region was optimized to simultaneously obtain high power and efficiency. A common-source PA MMIC based on InP-based MOS-HEMTs was fabricated, and an interstage circuit was designed to maximize the S21 per unit stage in the broadband, resulting in a record-high power-added efficiency and wide bandwidth.
- 4 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (6) , 3073-3078
Low-Resistance and Low-Thermal-Budget Ohmic Contact by Introducing Periodic Microstructures for AlGaN/AlN/GaN HEMTs
In this study, we proposed a low-resistance and low-thermal-budget ohmic contact by introducing periodic microstructures for AlGaN/AlN/GaN high-electron-mobility transistors (HEMTs). Insertion of AlN spacer layers is effective in improving electron mobility but can degrade contact resistance, in general. An ohmic contact with periodic microstructures was fabricated through low-damage patterned recess etching and metallization via low-temperature annealing (600 °C). The optimization of structural parameters of periodic microstructures allowed a low contact resistance of 0.29 $\Omega \cdot $ mm, which is less than half of that of the conventional recessed ohmic contact prepared in this study. A simplified equivalent circuit model reproduced the experimental results and predicted that enhanced metal/channel direct contact areas contributed to the reduction of contact resistance. Pulsed current–voltage measurements revealed that an AlGaN/AlN/GaN HEMT with periodic microstructures showed considerably suppressed current collapse compared with that of a selective-area growth (SAG) ohmic contact, indicating that the introduction of trap states was suppressed in periodic-structured devices owing to low-thermal-budget processes. Under high off-stress conditions, periodic-structured devices showed the highest drain current at knee voltage compared to the devices with a conventional planar-recessed ohmic contact and an SAG ohmic contact. Therefore, ohmic contact with periodic microstructures is one of the best techniques to achieve low contact resistance with low-thermal-budget processes.
- 4 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (6) , 3073-3078
Low-Resistance and Low-Thermal-Budget Ohmic Contact by Introducing Periodic Microstructures for AlGaN/AlN/GaN HEMTs
In this study, we proposed a low-resistance and low-thermal-budget ohmic contact by introducing periodic microstructures for AlGaN/AlN/GaN high-electron-mobility transistors (HEMTs). Insertion of AlN spacer layers is effective in improving electron mobility but can degrade contact resistance, in general. An ohmic contact with periodic microstructures was fabricated through low-damage patterned recess etching and metallization via low-temperature annealing (600 °C). The optimization of structural parameters of periodic microstructures allowed a low contact resistance of 0.29 $\Omega \cdot $ mm, which is less than half of that of the conventional recessed ohmic contact prepared in this study. A simplified equivalent circuit model reproduced the experimental results and predicted that enhanced metal/channel direct contact areas contributed to the reduction of contact resistance. Pulsed current–voltage measurements revealed that an AlGaN/AlN/GaN HEMT with periodic microstructures showed considerably suppressed current collapse compared with that of a selective-area growth (SAG) ohmic contact, indicating that the introduction of trap states was suppressed in periodic-structured devices owing to low-thermal-budget processes. Under high off-stress conditions, periodic-structured devices showed the highest drain current at knee voltage compared to the devices with a conventional planar-recessed ohmic contact and an SAG ohmic contact. Therefore, ohmic contact with periodic microstructures is one of the best techniques to achieve low contact resistance with low-thermal-budget processes.
- 29 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 11 (11) , 1909-1916
Thermal Design of GaN-on-GaN HEMT Power Amplifier for a Selective Heating Microwave Oven
In this study, we investigated the heat dissipation characteristics of gallium nitride (GaN) high-electron mobility transistors (HEMTs) fabricated on a freestanding GaN substrate (GaN-on-GaN HEMTs) by simulation. Although the GaN substrate has a lower thermal conductivity than the conventional silicon carbide (SiC) substrate, it was demonstrated that the GaN-on-GaN HEMT has a thermal resistance comparable to the conventional GaN-on-SiC HEMT in a simulated structure composed of a 100- $\mu \text{m}$ -thick substrate and a 2- $\mu \text{m}$ -thick GaN epitaxial layer. This is because GaN-on-GaN has a higher thermal conductivity of the GaN epitaxial layer and a lower thermal boundary resistance than GaN-on-SiC. Next, the thermal design of a 400-W/eight-channel selective heating microwave oven, which consists of eight pairs of patch antennas and power amplifier (PA) modules, involving a 50-W-class GaN-on-GaN HEMT PA, a driving amplifier, an oscillator, and several circuits, was carried out. The fan and fin specifications and enclosure configuration have been optimized to keep the temperature of the metal base on which the PA modules are mounted below 40 °C during full operation. Excellent agreement between the oven thermal simulation and the prototype thermocouple measurements was confirmed for the temperature difference between the metal base and the ambient. Finally, device dimensions for reliable operation were determined by simulating the channel temperature of the GaN-on-GaN HEMT PA during microwave heating. To keep the maximum channel temperature below 200 °C, the simulated device layout with a unit gate width ( $W_{\mathrm {gu}}$ ) of 100– $300~\mu \text{m}$ and a gate-to-gate spacing ( $L_{\mathrm {gg}}$ ) of 30– $70~\mu \text{m}$ was acceptable at a drain efficiency ( $\eta _{\mathrm {D}}$ ) of 75%. However, appropriate $W_{\mathrm {gu}}$ and $L_{\mathrm {gg}}$ were found to be required with a $\eta _{\mathrm {D}}$ of 65%.
- 29 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 11 (11) , 1909-1916
Thermal Design of GaN-on-GaN HEMT Power Amplifier for a Selective Heating Microwave Oven
In this study, we investigated the heat dissipation characteristics of gallium nitride (GaN) high-electron mobility transistors (HEMTs) fabricated on a freestanding GaN substrate (GaN-on-GaN HEMTs) by simulation. Although the GaN substrate has a lower thermal conductivity than the conventional silicon carbide (SiC) substrate, it was demonstrated that the GaN-on-GaN HEMT has a thermal resistance comparable to the conventional GaN-on-SiC HEMT in a simulated structure composed of a 100- $\mu \text{m}$ -thick substrate and a 2- $\mu \text{m}$ -thick GaN epitaxial layer. This is because GaN-on-GaN has a higher thermal conductivity of the GaN epitaxial layer and a lower thermal boundary resistance than GaN-on-SiC. Next, the thermal design of a 400-W/eight-channel selective heating microwave oven, which consists of eight pairs of patch antennas and power amplifier (PA) modules, involving a 50-W-class GaN-on-GaN HEMT PA, a driving amplifier, an oscillator, and several circuits, was carried out. The fan and fin specifications and enclosure configuration have been optimized to keep the temperature of the metal base on which the PA modules are mounted below 40 °C during full operation. Excellent agreement between the oven thermal simulation and the prototype thermocouple measurements was confirmed for the temperature difference between the metal base and the ambient. Finally, device dimensions for reliable operation were determined by simulating the channel temperature of the GaN-on-GaN HEMT PA during microwave heating. To keep the maximum channel temperature below 200 °C, the simulated device layout with a unit gate width ( $W_{\mathrm {gu}}$ ) of 100– $300~\mu \text{m}$ and a gate-to-gate spacing ( $L_{\mathrm {gg}}$ ) of 30– $70~\mu \text{m}$ was acceptable at a drain efficiency ( $\eta _{\mathrm {D}}$ ) of 75%. However, appropriate $W_{\mathrm {gu}}$ and $L_{\mathrm {gg}}$ were found to be required with a $\eta _{\mathrm {D}}$ of 65%.
- 18 September 2015
- Published by The Electrochemical Society in ECS Transactions
- Vol. 69 (2) , 161-166
Bias-dependent Photoabsorption Properties of GaN Porous Structures under Back-side Illumination
Photoabsorption properties of GaN porous structures were investigated by measuring photocurrent and transmittance under monochromatic light with various wavelengths. The measured photocurrents on the porous GaN electrode were larger than those on the planar electrodes, and those were observed even under illumination with lower photon energy than the bandgap energy of bulk GaN. Moreover, the light transmittance that was measured in the back-side illumination (BSI) mode depended strongly on the applied voltage to the porous electrode with change of the photocurrents. The observed photoabsorption properties can be qualitatively explained by the Franz-Keldysh effect; namely, the high electric field induced in the GaN porous structure easily causes a redshift of the photoabsorption edge.
- 18 September 2015
- Published by The Electrochemical Society in ECS Transactions
- Vol. 69 (2) , 161-166
Bias-dependent Photoabsorption Properties of GaN Porous Structures under Back-side Illumination
Photoabsorption properties of GaN porous structures were investigated by measuring photocurrent and transmittance under monochromatic light with various wavelengths. The measured photocurrents on the porous GaN electrode were larger than those on the planar electrodes, and those were observed even under illumination with lower photon energy than the bandgap energy of bulk GaN. Moreover, the light transmittance that was measured in the back-side illumination (BSI) mode depended strongly on the applied voltage to the porous electrode with change of the photocurrents. The observed photoabsorption properties can be qualitatively explained by the Franz-Keldysh effect; namely, the high electric field induced in the GaN porous structure easily causes a redshift of the photoabsorption edge.