Sam Shaanika
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sam Shaanika has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Oded Sobol
Bundesanstalt für Materialforschung und -prüfung (BAM), Berlin, Germany
5 shared publicationsThomas Alweendo
Faculty of Agriculture, Engineering and Natural Science, University of Namibia (UNAM), Windhoek, Namibia
5 shared publicationsEike Krafft
Cleanergy Solutions Namibia, Walvis Bay, Namibia
4 shared publicationsEster Angula
University of Namibia
3 shared publicationsMutiu Erinosho
University of Namibia
3 shared publicationsOluwagbenga Johnson
Faculty of Agriculture, Engineering and Natural Science, University of Namibia (UNAM), Windhoek, Namibia
3 shared publications
Latest Publications
- Open Access
- 16 October 2026
- Published by Springer Nature in Welding in the World
- p. 1-12
Compatibility of cold drawn and heat treated austenitic stainless steel (316L) tube for green hydrogen applications
Austenitic stainless steels are widely used for hydrogen handling and transport due to their corrosion resistance and generally low susceptibility to hydrogen-assisted cracking. However, soft zones introduced to material during fabrication and repairs or in services remains a concern for tube-based hydrogen distribution systems. In this work, a 316L (14,404) cold drawn 1/2″ (12.7 mm outer diameter) tube with wall thickness 1 mm was investigated in the cold drawn state and after weld-thermal cycle simulation by joule heating (heat-treated) state. Tube sections were machined into hollow tensile specimens and tested by slow strain rate tensile (SSRT) loading at the nominal strain rates of 1E-4 s −1 , 1E-5 s −1 and 1E-6 s −1 under the in situ gaseous hydrogen and in argon as reference (150 bar, room temperature). Additional precharging conditions were performed in the ex situ gaseous hydrogen autoclave precharging (1000 bar, 150 °C, 21 days) before SSRT. Tensile properties (ultimate tensile strength, yield strength, elongation, and reduction of area) were quantified, and hydrogen effects were expressed using degradation indices. The SSRT results at all strain rates indicate enhancement of strength and ductility in both the cold-drawn and heat-treated states. Across the investigated conditions, fracture surfaces showed predominantly ductile microvoid coalescence fracture. These findings contribute to the understanding of the compatibility of 316L tubing for hydrogen applications under the investigated conditions while highlighting the importance of processing state and hydrogen interactions.
- 16 October 2026
- Published by Springer Nature in Welding in the World
- p. 1-12
Open AccessCompatibility of cold drawn and heat treated austenitic stainless steel (316L) tube for green hydrogen applications
Austenitic stainless steels are widely used for hydrogen handling and transport due to their corrosion resistance and generally low susceptibility to hydrogen-assisted cracking. However, soft zones introduced to material during fabrication and repairs or in services remains a concern for tube-based hydrogen distribution systems. In this work, a 316L (14,404) cold drawn 1/2″ (12.7 mm outer diameter) tube with wall thickness 1 mm was investigated in the cold drawn state and after weld-thermal cycle simulation by joule heating (heat-treated) state. Tube sections were machined into hollow tensile specimens and tested by slow strain rate tensile (SSRT) loading at the nominal strain rates of 1E-4 s −1 , 1E-5 s −1 and 1E-6 s −1 under the in situ gaseous hydrogen and in argon as reference (150 bar, room temperature). Additional precharging conditions were performed in the ex situ gaseous hydrogen autoclave precharging (1000 bar, 150 °C, 21 days) before SSRT. Tensile properties (ultimate tensile strength, yield strength, elongation, and reduction of area) were quantified, and hydrogen effects were expressed using degradation indices. The SSRT results at all strain rates indicate enhancement of strength and ductility in both the cold-drawn and heat-treated states. Across the investigated conditions, fracture surfaces showed predominantly ductile microvoid coalescence fracture. These findings contribute to the understanding of the compatibility of 316L tubing for hydrogen applications under the investigated conditions while highlighting the importance of processing state and hydrogen interactions.
- Open Access
- 9 June 2026
- Published by Springer Nature in Research Square
Compatibility of cold drawn and heat treated austenitic stainless steel (316L) tube for green hydrogen applications
Austenitic stainless steels are widely used for hydrogen handling and transport due to their corrosion resistance and generally low susceptibility to hydrogen-assisted cracking. However, soft zones introduced to material during fabrication and repairs or in services remains a concern for tube-based hydrogen distribution systems. In this work, a 316L (14404) cold drawn 1/2"(12.7 mm outer diameter) tube with wall thickness 1 mm was investigated in the cold drawn state and after weld-thermal cycle simulation by joule heating (heat-treated) state. Tube sections were machined into hollow tensile specimens and tested by slow strain rate tensile (SSRT) loading at the nominal strain rates of 1E-4 s − 1 , 1E-5 s − 1 and 1E-6 s − 1 under the in-situ gaseous hydrogen and in argon as reference (150 bar, room temperature). Additional precharging conditions were performed in the ex-situ gaseous hydrogen autoclave precharging (1000 bar, 150°C, 21 days) before SSRT. Tensile properties (ultimate tensile strength, yield strength, elongation, and reduction of area) were quantified, and hydrogen effects were expressed using degradation indices. The SSRT results at all strain rates indicate enhancement of strength and ductility in both the cold drawn and heat-treated states. Across the investigated conditions, fracture surfaces showed predominantly ductile microvoid coalescence fracture. These findings contribute to the understanding of the compatibility of 316L tubing for hydrogen applications under the investigated conditions while highlighting the importance of processing state and hydrogen interactions.
- 9 June 2026
- Published by Springer Nature in Research Square
Open AccessCompatibility of cold drawn and heat treated austenitic stainless steel (316L) tube for green hydrogen applications
Austenitic stainless steels are widely used for hydrogen handling and transport due to their corrosion resistance and generally low susceptibility to hydrogen-assisted cracking. However, soft zones introduced to material during fabrication and repairs or in services remains a concern for tube-based hydrogen distribution systems. In this work, a 316L (14404) cold drawn 1/2"(12.7 mm outer diameter) tube with wall thickness 1 mm was investigated in the cold drawn state and after weld-thermal cycle simulation by joule heating (heat-treated) state. Tube sections were machined into hollow tensile specimens and tested by slow strain rate tensile (SSRT) loading at the nominal strain rates of 1E-4 s − 1 , 1E-5 s − 1 and 1E-6 s − 1 under the in-situ gaseous hydrogen and in argon as reference (150 bar, room temperature). Additional precharging conditions were performed in the ex-situ gaseous hydrogen autoclave precharging (1000 bar, 150°C, 21 days) before SSRT. Tensile properties (ultimate tensile strength, yield strength, elongation, and reduction of area) were quantified, and hydrogen effects were expressed using degradation indices. The SSRT results at all strain rates indicate enhancement of strength and ductility in both the cold drawn and heat-treated states. Across the investigated conditions, fracture surfaces showed predominantly ductile microvoid coalescence fracture. These findings contribute to the understanding of the compatibility of 316L tubing for hydrogen applications under the investigated conditions while highlighting the importance of processing state and hydrogen interactions.
- Open Access
- 1 June 2026
- Published by Springer Nature in Research Square
Burst tests of orbital welded austenitic stainless steel (316L) tubes charged in pressurized hydrogen
Orbital TIG welding is extensively used to weld tube to tube in many industries such as food, chemical oil and gas. Nowadays, applications in hydrogen transportation remains an interesting challenge due to the material susceptibility to hydrogen assisted cracking. Hydrogen can be introduced to the material during welding, fabrication or in-service as tube may be exposure to harsh environment that can be classified as internal or external hydrogen sources. In this study, a 316L (1.4404) cold drawn 1/2"(12.7 mm OD) and 3/8" (9.53 mm OD) tube with 0.5 mm wall thickness was investigated. Cold drawn tube sections were machined into hollow orbital welded specimen. Experimental assessment of burst testing of the welded specimens was performed and comparison of the high-pressure gaseous hydrogen autoclave precharged (1000 bar, 150°C, 21 days) and non-precharged (controls). Precharged specimens showed modest increases in burst pressure (≈ 2–8%) relative to controls. Hydrogen degradation index was determined to quantify the susceptibility of material in the investigation conditions. Fractography revealed a ductile fracture morphology with coarser dimples, larger microvoids and secondary cracks present in the precharged specimens. Within the limits of the present replication, the data suggests that under the tested extreme charging condition 316L tubing retained burst capacity and did not exhibit classical hydrogen assisted cracking. The findings contribute to the understanding of compatibility of welded austenitic stainless steels for the green hydrogen applications.
- 1 June 2026
- Published by Springer Nature in Research Square
Open AccessBurst tests of orbital welded austenitic stainless steel (316L) tubes charged in pressurized hydrogen
Orbital TIG welding is extensively used to weld tube to tube in many industries such as food, chemical oil and gas. Nowadays, applications in hydrogen transportation remains an interesting challenge due to the material susceptibility to hydrogen assisted cracking. Hydrogen can be introduced to the material during welding, fabrication or in-service as tube may be exposure to harsh environment that can be classified as internal or external hydrogen sources. In this study, a 316L (1.4404) cold drawn 1/2"(12.7 mm OD) and 3/8" (9.53 mm OD) tube with 0.5 mm wall thickness was investigated. Cold drawn tube sections were machined into hollow orbital welded specimen. Experimental assessment of burst testing of the welded specimens was performed and comparison of the high-pressure gaseous hydrogen autoclave precharged (1000 bar, 150°C, 21 days) and non-precharged (controls). Precharged specimens showed modest increases in burst pressure (≈ 2–8%) relative to controls. Hydrogen degradation index was determined to quantify the susceptibility of material in the investigation conditions. Fractography revealed a ductile fracture morphology with coarser dimples, larger microvoids and secondary cracks present in the precharged specimens. Within the limits of the present replication, the data suggests that under the tested extreme charging condition 316L tubing retained burst capacity and did not exhibit classical hydrogen assisted cracking. The findings contribute to the understanding of compatibility of welded austenitic stainless steels for the green hydrogen applications.
- Open Access
- 10 April 2026
- Published by Springer Nature in Welding in the World
Burst tests of cold drawn and heat treated austenitic stainless steel (316L) tubes charged in pressurized hydrogen
Global decarbonization targets are driving expansion of green hydrogen infrastructure, yet high-pressure hydrogen exposure can degrade the mechanical performance of critical stainless-steel components, typically made of the common steel 316L. This study evaluates the strength and fracture behavior of both cold-drawn and heat-treated 316L austenitic stainless-steel tubular specimens fabricated from 1/2″ (12.7 mm) and 3/8″ (9.53 mm) tube after gaseous high-pressure pre-charging with wall thickness 0.5 mm. Hydrogen concentration in the range between 76 and 100 ppm was measured in precharged sample in both states and the recorded quantity of 2–5 ppm in the non-precharged specimen. Hydrostatic burst tests at ambient temperature were carried out with precharged specimens and revealed an increase in burst pressure for both material states, as compared to non-precharged specimens as a reference. In addition, fractographic analysis by scanning electron microscopy has identified deeper dimples and wider microvoids in hydrogen-precharged specimens, indicating also some softening of the material in the cold-drawn as well as in the heat-treated state. As the time to failure also increased, it is anticipated that the hydrogen introduced in the specimens caused a respective increase in both, ductility in terms of the straining and deformation capacity, as well as an increase in strength. For engineering applications, the findings indicate some beneficial effect that, despite exposure to extreme hydrogen conditions, 316L tubes retain, and even modestly enhance, their structural integrity, supporting a safe deployment in green hydrogen transport and storage systems, at least at ambient temperature.
- 10 April 2026
- Published by Springer Nature in Welding in the World
Open AccessBurst tests of cold drawn and heat treated austenitic stainless steel (316L) tubes charged in pressurized hydrogen
Global decarbonization targets are driving expansion of green hydrogen infrastructure, yet high-pressure hydrogen exposure can degrade the mechanical performance of critical stainless-steel components, typically made of the common steel 316L. This study evaluates the strength and fracture behavior of both cold-drawn and heat-treated 316L austenitic stainless-steel tubular specimens fabricated from 1/2″ (12.7 mm) and 3/8″ (9.53 mm) tube after gaseous high-pressure pre-charging with wall thickness 0.5 mm. Hydrogen concentration in the range between 76 and 100 ppm was measured in precharged sample in both states and the recorded quantity of 2–5 ppm in the non-precharged specimen. Hydrostatic burst tests at ambient temperature were carried out with precharged specimens and revealed an increase in burst pressure for both material states, as compared to non-precharged specimens as a reference. In addition, fractographic analysis by scanning electron microscopy has identified deeper dimples and wider microvoids in hydrogen-precharged specimens, indicating also some softening of the material in the cold-drawn as well as in the heat-treated state. As the time to failure also increased, it is anticipated that the hydrogen introduced in the specimens caused a respective increase in both, ductility in terms of the straining and deformation capacity, as well as an increase in strength. For engineering applications, the findings indicate some beneficial effect that, despite exposure to extreme hydrogen conditions, 316L tubes retain, and even modestly enhance, their structural integrity, supporting a safe deployment in green hydrogen transport and storage systems, at least at ambient temperature.
- Open Access
- 19 February 2026
- Published by Springer Nature in Research Square
Burst tests of cold drawn and heat treated austenitic stainless steel (316L) tubes charged in pressurized hydrogen
Global decarbonization targets are driving expansion of green hydrogen infrastructure, yet high-pressure hydrogen exposure can degrade the mechanical performance of critical stainless-steel components, typically made of the common steel 316L. This study evaluates the strength and fracture behaviour of both cold-drawn and heat treated 316L austenitic stainless-steel tubular specimens fabricated from 1/2" (12.7 mm) and 3/8" (9.53 mm) tube after gaseous high pressure pre-charging. Hydrogen concentration in the range between 76–100 ppm was measured in precharged sample in both states and the record of 2–5 ppm in the none-precharged specimen. Hydrostatic burst tests at ambient temperature were carried out with precharged specimens and revealed an increase in burst pressure for both material states, as compared to non-precharged specimens as a reference. In addition, fractographic analysis by scanning electron microscopy identified deeper dimples and wider microvoids in hydrogen-precharged specimens, indicating also some softening of the material in the cold drawn as well as in the heat-treated state. As the time to failure also increased, it is anticipated that the hydrogen introduced in the specimens caused a respective increase in both, ductility in terms of the straining and deformation capacity, as well as an increase in strength. For engineering applications, the findings indicate some beneficial effect that, despite exposure to extreme hydrogen conditions, 316L tubes retain, and even modestly enhance, their structural integrity, supporting a safe deployment in green hydrogen transport and storage systems, at least at ambient temperature.
- 19 February 2026
- Published by Springer Nature in Research Square
Open AccessBurst tests of cold drawn and heat treated austenitic stainless steel (316L) tubes charged in pressurized hydrogen
Global decarbonization targets are driving expansion of green hydrogen infrastructure, yet high-pressure hydrogen exposure can degrade the mechanical performance of critical stainless-steel components, typically made of the common steel 316L. This study evaluates the strength and fracture behaviour of both cold-drawn and heat treated 316L austenitic stainless-steel tubular specimens fabricated from 1/2" (12.7 mm) and 3/8" (9.53 mm) tube after gaseous high pressure pre-charging. Hydrogen concentration in the range between 76–100 ppm was measured in precharged sample in both states and the record of 2–5 ppm in the none-precharged specimen. Hydrostatic burst tests at ambient temperature were carried out with precharged specimens and revealed an increase in burst pressure for both material states, as compared to non-precharged specimens as a reference. In addition, fractographic analysis by scanning electron microscopy identified deeper dimples and wider microvoids in hydrogen-precharged specimens, indicating also some softening of the material in the cold drawn as well as in the heat-treated state. As the time to failure also increased, it is anticipated that the hydrogen introduced in the specimens caused a respective increase in both, ductility in terms of the straining and deformation capacity, as well as an increase in strength. For engineering applications, the findings indicate some beneficial effect that, despite exposure to extreme hydrogen conditions, 316L tubes retain, and even modestly enhance, their structural integrity, supporting a safe deployment in green hydrogen transport and storage systems, at least at ambient temperature.
- 5 November 2025
- Published by Trans Tech Publications, Ltd. in Engineering Headway
- Vol. 28, 133-143
Development of Potatoes Harvesting Machine for Small-Scale Farming
Manual potato harvesting is labour-intensive and time-consuming for small-scale farmers due to the high cost and inaccessibility of industrial machinery. This study presents the development of a small-scale potato harvester that integrates digging and sieving mechanisms. Three design concepts were assessed based on capital investment, size, maintenance, effectiveness, and digger adjustability. A detailed design analysis determined key specifications, including machine dimensions (2.385 m × 1.07 m × 1.083 m), cutting share width (0.51 m), weight (180 kg), field capacity (0.101 ha/h), and operating speed (3.5 km/h). The digger is designed to rotate for adaptability to varying soil slopes and is vertically adjustable for different depths. The estimated cost of the developed harvester is approximately N$30,000, making it a cost-effective alternative to industrial machines. The designed mechanized potato-harvesting machine is expected to significantly reduce labour, improve overall efficiency, and enhance productivity, thereby easing the harvesting process for small-scale farmers. The isometric view of the potato harvester, designed in SOLIDWORKS®, illustrates the final design.
- 5 November 2025
- Published by Trans Tech Publications, Ltd. in Engineering Headway
- Vol. 28, 133-143
Development of Potatoes Harvesting Machine for Small-Scale Farming
Manual potato harvesting is labour-intensive and time-consuming for small-scale farmers due to the high cost and inaccessibility of industrial machinery. This study presents the development of a small-scale potato harvester that integrates digging and sieving mechanisms. Three design concepts were assessed based on capital investment, size, maintenance, effectiveness, and digger adjustability. A detailed design analysis determined key specifications, including machine dimensions (2.385 m × 1.07 m × 1.083 m), cutting share width (0.51 m), weight (180 kg), field capacity (0.101 ha/h), and operating speed (3.5 km/h). The digger is designed to rotate for adaptability to varying soil slopes and is vertically adjustable for different depths. The estimated cost of the developed harvester is approximately N$30,000, making it a cost-effective alternative to industrial machines. The designed mechanized potato-harvesting machine is expected to significantly reduce labour, improve overall efficiency, and enhance productivity, thereby easing the harvesting process for small-scale farmers. The isometric view of the potato harvester, designed in SOLIDWORKS®, illustrates the final design.
- 18 October 2023
- Published by Springer Nature
- p. 59-65
Design and Fabrication of a Livestock’s Fodder Crusher
- 18 October 2023
- Published by Springer Nature
- p. 59-65
Design and Fabrication of a Livestock’s Fodder Crusher
- 18 October 2023
- Published by Springer Nature
- p. 66-72
Design of a Solar PV Water Pumping System for Small-Scale Farming Along the Calueque-Oshakati Canal in Namibia
- 18 October 2023
- Published by Springer Nature
- p. 66-72
Design of a Solar PV Water Pumping System for Small-Scale Farming Along the Calueque-Oshakati Canal in Namibia
- 6 July 2021
- Published by Springer Nature
- p. 10-16
Development of a Parabolic Trough Solar Water Heater for Domestic Houses in Ongwediva
- 6 July 2021
- Published by Springer Nature
- p. 10-16
Development of a Parabolic Trough Solar Water Heater for Domestic Houses in Ongwediva