Carlo Boaretti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Carlo Boaretti has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Martina Roso
Department of Industrial Engineering, University of Padova, via Marzolo 9, 35131 Padova, Italy
15 shared publications - Alessandra Lorenzetti
Department of Industrial Engineering, University of Padova, via Marzolo 9, 35131 Padova, Italy
14 shared publications - Michele Modesti
Department of Industrial Engineering, University of Padova, via Marzolo 9, 35131 Padova, Italy
14 shared publications - Eleonora Dal Lago
LaPrima Green Solutions S.r.l., Viale Europa, 46, 36033 Isola Vicentina, Italy
5 shared publications Michele Modesti
Department of Industrial Engineering, University of Padova, Padova, Italy
4 shared publications- Riccardo Donadini
Department of Industrial Engineering University of Padova via Marzolo 9 Padova 35131 Italy
4 shared publications
Latest Publications
- Open Access
- 18 May 2026
- Published by Springer Nature in Communications Chemistry
- Vol. 9 (1)
Ionolysis of flexible polyurethane waste using ionic liquids for efficient and sustainable polyol recovery
Chemical recycling of polyurethane waste is essential for advancing circular economy objectives, as current technologies struggle to efficiently recover monomeric building blocks. Here, we present an efficient ionolysis-based recycling approach using 1-ethyl-3-methylimidazolium bromide (EMIM-Br) as bifunctional solvent-catalyst. Under mild conditions (150°C, 1 MPa), the ionic liquid disrupts hydrogen bonding and selectively cleaves urethane linkages, yielding virgin-like polyols. Polyols are efficiently separated from the reaction mixture, and the ionic liquid is readily recycled. EMIM-Br achieved a 94% depolymerization yield and 73% polyol recovery. Physicochemical analysis confirmed that the recovered polyols closely match commercial standards. Notably, incorporation of 25% recycled polyol into new formulations produced flexible PU foams with viscoelastic properties comparable to those of the reference material. This work offers a sustainable and scalable strategy for polyurethane foam recycling, addressing key limitations in current technologies and supporting resource-efficient materials development.
- 18 May 2026
- Published by Springer Nature in Communications Chemistry
- Vol. 9 (1)
Open AccessIonolysis of flexible polyurethane waste using ionic liquids for efficient and sustainable polyol recovery
Chemical recycling of polyurethane waste is essential for advancing circular economy objectives, as current technologies struggle to efficiently recover monomeric building blocks. Here, we present an efficient ionolysis-based recycling approach using 1-ethyl-3-methylimidazolium bromide (EMIM-Br) as bifunctional solvent-catalyst. Under mild conditions (150°C, 1 MPa), the ionic liquid disrupts hydrogen bonding and selectively cleaves urethane linkages, yielding virgin-like polyols. Polyols are efficiently separated from the reaction mixture, and the ionic liquid is readily recycled. EMIM-Br achieved a 94% depolymerization yield and 73% polyol recovery. Physicochemical analysis confirmed that the recovered polyols closely match commercial standards. Notably, incorporation of 25% recycled polyol into new formulations produced flexible PU foams with viscoelastic properties comparable to those of the reference material. This work offers a sustainable and scalable strategy for polyurethane foam recycling, addressing key limitations in current technologies and supporting resource-efficient materials development.
- Open Access
Mitigating Composition Variability in Post-Industrial PC/ABS Recycling via Targeted Compatibilization
The growing demand for sustainable solutions in the plastics industry has highlighted the need to reintroduce post-industrial polymer waste into high-performance applications. This study focuses on the mechanical recycling of automotive scraps containing variable proportions of polycarbonate (PC), acrylonitrile–butadiene–styrene (ABS), and a commercial PC/ABS blend. After determining the composition of two representative batches, a screening of seven commercial compatibilizers and impact modifiers was performed to improve impact strength. Among them, an ethylene–methyl acrylate–glycidyl methacrylate (E-MA-GMA) terpolymer was identified as the most effective additive. Its influence was further investigated through a mixture design approach, varying the composition of the three polymer phases and the additive content (0–10 wt.%). The resulting response surface model revealed a significant increase in impact resistance in PC-rich formulations with increasing E-MA-GMA content, while ABS and PC/ABS showed more complex trends. Rheological, mechanical, and thermal analyses supported the observed behavior, suggesting improved matrix compatibility and reduced degradation during processing. The proposed model enables the prediction of impact performance across a wide range of compositions, offering a practical tool for the optimization of recycled blends. These findings support the potential of targeted compatibilization strategies for closed-loop recycling in the automotive sector.
Open AccessMitigating Composition Variability in Post-Industrial PC/ABS Recycling via Targeted Compatibilization
The growing demand for sustainable solutions in the plastics industry has highlighted the need to reintroduce post-industrial polymer waste into high-performance applications. This study focuses on the mechanical recycling of automotive scraps containing variable proportions of polycarbonate (PC), acrylonitrile–butadiene–styrene (ABS), and a commercial PC/ABS blend. After determining the composition of two representative batches, a screening of seven commercial compatibilizers and impact modifiers was performed to improve impact strength. Among them, an ethylene–methyl acrylate–glycidyl methacrylate (E-MA-GMA) terpolymer was identified as the most effective additive. Its influence was further investigated through a mixture design approach, varying the composition of the three polymer phases and the additive content (0–10 wt.%). The resulting response surface model revealed a significant increase in impact resistance in PC-rich formulations with increasing E-MA-GMA content, while ABS and PC/ABS showed more complex trends. Rheological, mechanical, and thermal analyses supported the observed behavior, suggesting improved matrix compatibility and reduced degradation during processing. The proposed model enables the prediction of impact performance across a wide range of compositions, offering a practical tool for the optimization of recycled blends. These findings support the potential of targeted compatibilization strategies for closed-loop recycling in the automotive sector.
- Open Access
Mechanical Recycling of Post-Industrial PC/ABS Blends from the Automotive Sector by Mixture Design
The widespread use of plastic materials poses significant environmental challenges, which have promoted a growing call for a circular approach to such materials, emphasizing waste reintegration into production. From this perspective, the present study focuses on analyzing a post-industrial recycled stream of chrome-plated automotive scraps composed of acrylonitrile–butadiene–styrene (ABS), polycarbonate (PC), and a commercial PC/ABS blend. The batch-to-batch varying proportions of these constituents make control of the recycled materials’ quality challenging. To address this problem, we formulated an I-optimal mixture design model using the infrared absorbance ratio of selected peaks and Izod impact resistance results for injection-molded samples as inputs to determine the composition of each batch quickly. The two model equations (adjusted R2 > 0.97) obtained, based on cubic expression and regressed from data obtained from 27 mixtures with known compositions, were combined into a single system for the determination of unknown batch compositions. The validation test showed that the models can satisfactorily predict both the infrared and Izod results of blends with known compositions, but in the latter case, the results are less reliable, probably due to specific blend morphological interactions according to specific compositions. The results can improve mechanical recycling methodologies for reintroducing plastic wastes to the market.
Open AccessMechanical Recycling of Post-Industrial PC/ABS Blends from the Automotive Sector by Mixture Design
The widespread use of plastic materials poses significant environmental challenges, which have promoted a growing call for a circular approach to such materials, emphasizing waste reintegration into production. From this perspective, the present study focuses on analyzing a post-industrial recycled stream of chrome-plated automotive scraps composed of acrylonitrile–butadiene–styrene (ABS), polycarbonate (PC), and a commercial PC/ABS blend. The batch-to-batch varying proportions of these constituents make control of the recycled materials’ quality challenging. To address this problem, we formulated an I-optimal mixture design model using the infrared absorbance ratio of selected peaks and Izod impact resistance results for injection-molded samples as inputs to determine the composition of each batch quickly. The two model equations (adjusted R2 > 0.97) obtained, based on cubic expression and regressed from data obtained from 27 mixtures with known compositions, were combined into a single system for the determination of unknown batch compositions. The validation test showed that the models can satisfactorily predict both the infrared and Izod results of blends with known compositions, but in the latter case, the results are less reliable, probably due to specific blend morphological interactions according to specific compositions. The results can improve mechanical recycling methodologies for reintroducing plastic wastes to the market.
- Open Access
- 28 November 2023
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 12 (1)
Boosting the photocatalytic performance of PAN-TiO2 nanostructured membranes by mechanosynthesis
- 28 November 2023
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 12 (1)
Open AccessBoosting the photocatalytic performance of PAN-TiO2 nanostructured membranes by mechanosynthesis
- Open Access
- 20 November 2023
- Published by Wiley in Chemistry – A European Journal
- Vol. 30 (3) , e202301919
Deamination of Polyols from the Glycolysis of Polyurethane
Methylenedianiline (MDA) is a secondary, undesired, product of the glycolysis process of polyurethane (PU) scraps due to hydrolysis and pyrolysis side reactions. As an aromatic and carcinogen amine, MDA poses different problems in handling, transporting, and labelling recycled polyols derived from glycolysis, hindering the closure of PU recycling loop. Aiming to provide a solution to this issue, in this work different deaminating agents (DAs) were investigated with the purpose of analyzing their reactivity with MDA. A first part of the study was devoted to the analysis of MDA formation as a function of reaction time and catalyst concentration (potassium acetate) during glycolysis. It was observed that the amount of MDA increases almost linearly with the extent of PU depolymerization and catalyst content. Among the DAs analyzed 2‐ethylhexyl glycidyl ether (2‐EHGE), and acetic anhydride (Ac2O) showed interesting performance, which allowed MDA content to be diminished below the limit for labelling prescription in 30 minutes. PU rigid foams were, therefore, synthesized from the corresponding recycled products and characterized in terms of thermal and mechanical performance. Ac2O‐deaminated polyols led to structurally unstable foams with poor compressive strength, while 2‐EHGE‐deaminated products allowed the production of foams with improved mechanical performance and unaltered thermal conductivity.
- 20 November 2023
- Published by Wiley in Chemistry – A European Journal
- Vol. 30 (3) , e202301919
Open AccessDeamination of Polyols from the Glycolysis of Polyurethane
Methylenedianiline (MDA) is a secondary, undesired, product of the glycolysis process of polyurethane (PU) scraps due to hydrolysis and pyrolysis side reactions. As an aromatic and carcinogen amine, MDA poses different problems in handling, transporting, and labelling recycled polyols derived from glycolysis, hindering the closure of PU recycling loop. Aiming to provide a solution to this issue, in this work different deaminating agents (DAs) were investigated with the purpose of analyzing their reactivity with MDA. A first part of the study was devoted to the analysis of MDA formation as a function of reaction time and catalyst concentration (potassium acetate) during glycolysis. It was observed that the amount of MDA increases almost linearly with the extent of PU depolymerization and catalyst content. Among the DAs analyzed 2‐ethylhexyl glycidyl ether (2‐EHGE), and acetic anhydride (Ac2O) showed interesting performance, which allowed MDA content to be diminished below the limit for labelling prescription in 30 minutes. PU rigid foams were, therefore, synthesized from the corresponding recycled products and characterized in terms of thermal and mechanical performance. Ac2O‐deaminated polyols led to structurally unstable foams with poor compressive strength, while 2‐EHGE‐deaminated products allowed the production of foams with improved mechanical performance and unaltered thermal conductivity.
- Open Access
- 27 January 2023
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 8 (5) , 4655-4666
Chemical Recycling of Polyurethane Waste via a Microwave-Assisted Glycolysis Process
In this work, we explored a microwave-assisted glycolysis process to chemically recycle rigid polyurethane (PU) foam waste to obtain a single-phase product with suitable physio-chemical properties as a secondary raw material for the preparation of new rigid PU products. Such an approach was compared to a conventionally heated (ConvH) process, analyzing the performances of different catalysts. The use of microwaves allowed a 94% decrease in the reaction time scale of rigid PU depolymerization, with a concurrent 45% reduction in energy expense. By using a PU/diethylene glycol mass ratio of 1.5, best performances were obtained with a 30 mmol/100gPU potassium acetate concentration, both in terms of the product viscosity and aromatic amine byproduct content. The glycolysis products recovered were employed in substitution to virgin polyol for rigid PU foam preparation, showing improved compressive strength and comparable thermal insulation properties up to a 30% content with respect to the traditional non-recycled counterpart.
- 27 January 2023
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 8 (5) , 4655-4666
Open AccessChemical Recycling of Polyurethane Waste via a Microwave-Assisted Glycolysis Process
In this work, we explored a microwave-assisted glycolysis process to chemically recycle rigid polyurethane (PU) foam waste to obtain a single-phase product with suitable physio-chemical properties as a secondary raw material for the preparation of new rigid PU products. Such an approach was compared to a conventionally heated (ConvH) process, analyzing the performances of different catalysts. The use of microwaves allowed a 94% decrease in the reaction time scale of rigid PU depolymerization, with a concurrent 45% reduction in energy expense. By using a PU/diethylene glycol mass ratio of 1.5, best performances were obtained with a 30 mmol/100gPU potassium acetate concentration, both in terms of the product viscosity and aromatic amine byproduct content. The glycolysis products recovered were employed in substitution to virgin polyol for rigid PU foam preparation, showing improved compressive strength and comparable thermal insulation properties up to a 30% content with respect to the traditional non-recycled counterpart.
- Open Access
- 20 January 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (3) , 435
Ultrasound-Promoted Abatement of Formaldehyde in Liquid Phase with Electrospun Nanostructured Membranes: The Synergy of Combined AOPs
The present work investigates the effect of ultrasounds in the performance of combined advanced oxidation processes (AOPs) on the degradation of formaldehyde (HCHO)-polluted aqueous solutions for potential application in wastewater treatment. Different heterogeneous nanostructured catalysts based on TiO2 and FeSO4 for photocatalysis and the Fenton process were employed after electrospray deposition on electrospun nanofibrous membranes. Such systems were tested, without the use of any added hydrogen peroxide, by varying the combinations among the selected AOPs in a batch reactor configuration. The results show that, in the absence of a Fenton reaction, ultrasounds provided a significantly increased formaldehyde photocatalytic abatement, probably by increasing the concentration of active species through a different set of reactions while providing a favorable mass transfer regime by the cavitational effect. Due to the faster kinetics of the photo–Fenton process, thanks to its partial homogeneous nature, such a beneficial effect is more limited for the sono–photo–Fenton configuration. On the other hand, the employment of a sono–photocatalytic–Fenton process revealed a synergic effect that provided the best results, reducing the formaldehyde concentration to less than 99% after 240 min. Further analysis showed that, due to a mutual influence, only a tailored TiO2/FeSO4 ratio on the membranes was able to display the best performance.
- 20 January 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (3) , 435
Open AccessUltrasound-Promoted Abatement of Formaldehyde in Liquid Phase with Electrospun Nanostructured Membranes: The Synergy of Combined AOPs
The present work investigates the effect of ultrasounds in the performance of combined advanced oxidation processes (AOPs) on the degradation of formaldehyde (HCHO)-polluted aqueous solutions for potential application in wastewater treatment. Different heterogeneous nanostructured catalysts based on TiO2 and FeSO4 for photocatalysis and the Fenton process were employed after electrospray deposition on electrospun nanofibrous membranes. Such systems were tested, without the use of any added hydrogen peroxide, by varying the combinations among the selected AOPs in a batch reactor configuration. The results show that, in the absence of a Fenton reaction, ultrasounds provided a significantly increased formaldehyde photocatalytic abatement, probably by increasing the concentration of active species through a different set of reactions while providing a favorable mass transfer regime by the cavitational effect. Due to the faster kinetics of the photo–Fenton process, thanks to its partial homogeneous nature, such a beneficial effect is more limited for the sono–photo–Fenton configuration. On the other hand, the employment of a sono–photocatalytic–Fenton process revealed a synergic effect that provided the best results, reducing the formaldehyde concentration to less than 99% after 240 min. Further analysis showed that, due to a mutual influence, only a tailored TiO2/FeSO4 ratio on the membranes was able to display the best performance.
- Open Access
- 16 June 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (25) , 21775-21787
Investigation and Optimization of Vacuum Plasma Treatment of PA66 Fabric for Reduced Fire Retardant Consumption
Flame retardant (FR) textiles were obtained by surface treatments of polyamide 66 fabrics with microwave (MW) plasma technology in order to reduce the amount of FR involved in the fabric finishing process. More specifically, MW vacuum plasma was employed for polymer surface activation by using a helium/oxygen (He/O2) gas mixture, evaluating the effect of different treatment parameters on the affinity toward thiourea impregnation. Surface fabric modification was investigated both in terms of uniformity and increased thiourea absorption by infrared spectroscopy, wicking properties, and gravimetric characterization to define an operative window for plasma treatment conditions. According to the results obtained, the dry add-on content of thiourea improved up to 38%, thanks to the increase of the fabric surface activation. The effectiveness of plasma treatment resulted in an absolute increase up to 2% in limiting oxygen index (LOI) performance with respect to untreated fabric. As a consequence, a drastic reduction of 50% in thiourea concentration was required to achieve a similar fire retardant performance for plasma-treated fabric. On the basis of these preliminary results, a design of experiment (DoE) methodology was applied to the selected parameters to build a suitable response surface, experimentally validated, and to identify optimized treatment conditions. At the end, a final LOI index up to 43% has been reached.
- 16 June 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (25) , 21775-21787
Open AccessInvestigation and Optimization of Vacuum Plasma Treatment of PA66 Fabric for Reduced Fire Retardant Consumption
Flame retardant (FR) textiles were obtained by surface treatments of polyamide 66 fabrics with microwave (MW) plasma technology in order to reduce the amount of FR involved in the fabric finishing process. More specifically, MW vacuum plasma was employed for polymer surface activation by using a helium/oxygen (He/O2) gas mixture, evaluating the effect of different treatment parameters on the affinity toward thiourea impregnation. Surface fabric modification was investigated both in terms of uniformity and increased thiourea absorption by infrared spectroscopy, wicking properties, and gravimetric characterization to define an operative window for plasma treatment conditions. According to the results obtained, the dry add-on content of thiourea improved up to 38%, thanks to the increase of the fabric surface activation. The effectiveness of plasma treatment resulted in an absolute increase up to 2% in limiting oxygen index (LOI) performance with respect to untreated fabric. As a consequence, a drastic reduction of 50% in thiourea concentration was required to achieve a similar fire retardant performance for plasma-treated fabric. On the basis of these preliminary results, a design of experiment (DoE) methodology was applied to the selected parameters to build a suitable response surface, experimentally validated, and to identify optimized treatment conditions. At the end, a final LOI index up to 43% has been reached.
- Open Access
- 14 March 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (6) , 962
Effects of Solvent and Electrospinning Parameters on the Morphology and Piezoelectric Properties of PVDF Nanofibrous Membrane
PVDF electrospun membranes were prepared by employing different mixtures of solvents and diverse electrospinning parameters. A comprehensive investigation was carried out, including morphology, nanofiber diameter, crystallinity, β-phase fraction, and piezoelectric response under external mechanical strain. It was demonstrated that by using low-toxicity DMSO as the solvent, PVDF membranes with good morphology (bead-free, smooth surface, and uniform nanofiber) can be obtained. All the fabricated membranes showed crystallinity and β-phase fraction above 48% and 80%, respectively; therefore, electrospinning is a good method for preparing PVDF membranes with the piezoelectric properties. Moreover, we considered a potential effect of the solvent properties and the electrospinning parameters on the final piezoelectric properties. When PVDF membranes with different β-phase fractions and crystallinity values are applied to make the piezoelectric transducers, various piezoelectric voltage outputs can be obtained. This paper provides an effective and efficient strategy for regulating the piezoelectric properties of PVDF electrospun membranes by controlling both solvent dipole moment and process parameters. To the best of our knowledge, this is the first time that the influence of a solvent’s dipole moment on the piezoelectric properties of electrospun materials has been reported.
- 14 March 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (6) , 962
Open AccessEffects of Solvent and Electrospinning Parameters on the Morphology and Piezoelectric Properties of PVDF Nanofibrous Membrane
PVDF electrospun membranes were prepared by employing different mixtures of solvents and diverse electrospinning parameters. A comprehensive investigation was carried out, including morphology, nanofiber diameter, crystallinity, β-phase fraction, and piezoelectric response under external mechanical strain. It was demonstrated that by using low-toxicity DMSO as the solvent, PVDF membranes with good morphology (bead-free, smooth surface, and uniform nanofiber) can be obtained. All the fabricated membranes showed crystallinity and β-phase fraction above 48% and 80%, respectively; therefore, electrospinning is a good method for preparing PVDF membranes with the piezoelectric properties. Moreover, we considered a potential effect of the solvent properties and the electrospinning parameters on the final piezoelectric properties. When PVDF membranes with different β-phase fractions and crystallinity values are applied to make the piezoelectric transducers, various piezoelectric voltage outputs can be obtained. This paper provides an effective and efficient strategy for regulating the piezoelectric properties of PVDF electrospun membranes by controlling both solvent dipole moment and process parameters. To the best of our knowledge, this is the first time that the influence of a solvent’s dipole moment on the piezoelectric properties of electrospun materials has been reported.
- 29 November 2021
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 60 (48) , 17750-17760
Transesterification of Bis(2-Ethylhexyl) Phthalate for the Recycling of Flexible Polyvinyl Chloride Scraps in the Circular Economy Framework
- 29 November 2021
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 60 (48) , 17750-17760
Transesterification of Bis(2-Ethylhexyl) Phthalate for the Recycling of Flexible Polyvinyl Chloride Scraps in the Circular Economy Framework