Xue Bai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xue Bai has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Leijun Xu
School of Electrical and Information Engineering, Jiangsu University, Zhenjiang 212013, China
5 shared publications Jianfeng Chen
School of Electrical and Information Engineering, Jiangsu University, Zhenjiang 212013, People’s Republic of China
2 shared publications- Jianfeng Chen
School of Electrical and Information Engineering, Jiangsu University, Zhenjiang 212013, People’s Republic of China
2 shared publications - Xinke Zhao
School of Electrical and Information Engineering, Jiangsu University, Zhenjiang 212013, People’s Republic of China
2 shared publications - Chen Chen
School of Low-Altitude Technology, Jiangsu University, Zhenjiang 212013, China
1 shared publication - Fan Xie
School of Electrical and Information Engineering, Jiangsu University, Zhenjiang 212013, People’s Republic of China
1 shared publication
Latest Publications
- 16 March 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (11) , 115503
Flexible rectifying metasurfaces for efficient wireless energy harvesting
A highly efficient, ultra-thin, and flexible rectifying metasurface (RMS) operating at 5.8 GHz is presented. The unit cell utilizes a composite symmetric structure. This structure consists of a double-cross and a notched rectangular ring. This geometric symmetry ensures polarization insensitivity. Structural parameters were optimized to achieve simultaneous impedance matching. The metasurface matches the impedance of free space ( Z 0 ) and provides a conjugate match to the diodes. This eliminates the need for external matching networks, thereby significantly enhancing system integration. Furthermore, the high-Q chip inductors within the interconnect units serve both as direct current (DC) pathways and, in conjunction with the unit’s inherent parasitic capacitance, form radio frequency (RF) filters. This coplanar integration obviates the need for a separate power combining network. A 6×6 array (96 mm × 96 mm) was fabricated on a 0.6 mm thick polyimide substrate. Experimental measurements demonstrate a total efficiency exceeding 67% across all polarization angles. The efficiency remains above 64.2% within an incident angle range of 0° to 30°. Additionally, the system maintains an efficiency of 66.74% when bent to a curvature radius of 180 mm. These results demonstrate excellent conformability. These attributes make the proposed RMS a highly efficient and compact solution for wireless power delivery, particularly for Internet of Things (IoT) and wearable applications.
- 16 March 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (11) , 115503
Flexible rectifying metasurfaces for efficient wireless energy harvesting
A highly efficient, ultra-thin, and flexible rectifying metasurface (RMS) operating at 5.8 GHz is presented. The unit cell utilizes a composite symmetric structure. This structure consists of a double-cross and a notched rectangular ring. This geometric symmetry ensures polarization insensitivity. Structural parameters were optimized to achieve simultaneous impedance matching. The metasurface matches the impedance of free space ( Z 0 ) and provides a conjugate match to the diodes. This eliminates the need for external matching networks, thereby significantly enhancing system integration. Furthermore, the high-Q chip inductors within the interconnect units serve both as direct current (DC) pathways and, in conjunction with the unit’s inherent parasitic capacitance, form radio frequency (RF) filters. This coplanar integration obviates the need for a separate power combining network. A 6×6 array (96 mm × 96 mm) was fabricated on a 0.6 mm thick polyimide substrate. Experimental measurements demonstrate a total efficiency exceeding 67% across all polarization angles. The efficiency remains above 64.2% within an incident angle range of 0° to 30°. Additionally, the system maintains an efficiency of 66.74% when bent to a curvature radius of 180 mm. These results demonstrate excellent conformability. These attributes make the proposed RMS a highly efficient and compact solution for wireless power delivery, particularly for Internet of Things (IoT) and wearable applications.
- 1 March 2026
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 41 (3) , 035015
High-responsivity CMOS terahertz detector with integrated readout circuit
This paper presents a highly integrated terahertz (THz) detector operating at 350 GHz, fabricated in a TSMC 0.18 μ m CMOS process. The mixer employs a novel cross-coupled gate-source topology with drain biasing to enhance detection performance, departing from conventional architectures. Furthermore, the integration of a low-noise operational amplifier and a 10-bit successive approximation register analog-to-digital converter enables on-chip readout of weak signals—eliminating the need for external PCB-based signal conditioning. The proposed design achieves a peak voltage responsivity (R V ) of 11 kV W −1 and a minimum noise equivalent power (NEP) of 8.9 pW Hz −1/2 at 350 GHz. The total chip area is 1.0 mm × 0.6 mm. Experimental results confirm that the detector simultaneously delivers high responsivity and fully integrated digital signal processing capability.
- 1 March 2026
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 41 (3) , 035015
High-responsivity CMOS terahertz detector with integrated readout circuit
This paper presents a highly integrated terahertz (THz) detector operating at 350 GHz, fabricated in a TSMC 0.18 μ m CMOS process. The mixer employs a novel cross-coupled gate-source topology with drain biasing to enhance detection performance, departing from conventional architectures. Furthermore, the integration of a low-noise operational amplifier and a 10-bit successive approximation register analog-to-digital converter enables on-chip readout of weak signals—eliminating the need for external PCB-based signal conditioning. The proposed design achieves a peak voltage responsivity (R V ) of 11 kV W −1 and a minimum noise equivalent power (NEP) of 8.9 pW Hz −1/2 at 350 GHz. The total chip area is 1.0 mm × 0.6 mm. Experimental results confirm that the detector simultaneously delivers high responsivity and fully integrated digital signal processing capability.
- 21 November 2024
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 39 (12) , 125018
CMOS dual-band terahertz on-chip antenna array and detector design
In this paper, in response to the limitations of conventional single-pixel terahertz (THz) detectors in detecting a single frequency band and having a low imaging resolution. A dual-band high responsivity (Rv) array detector scheme is proposed. Includes dual-band high-gain on-chip antenna, matching circuit, dual-band self-mixing receiver circuit and integrated voltage amplifier. The proposed on-chip antenna uses a multi-loop nested design based on the octagonal antenna to realize the dual-band high gain characteristics. In addition, the use of ‘cross-loop’ metal modules as ground plane isolation effectively reduces the electromagnetic interference between the units in the array and ensures the stable operation of the detector array. The matching circuit realizes the maximum power transmission of THz signals between the antenna and the receiving circuit, improved detector Rv. The integrated two-stage voltage amplifier is able to effectively amplify the signal output from the receiver circuit to further increase the detector response voltage. The designed detector is fabricated using 0.18 μm CMOS process. Simulation results show that the antenna has a maximum gain of 5.23 dBi in the 0.37 THz band and 6.77 dBi in the 0.76 THz band. The detector can detect in both 0.37 and 0.76 THz bands. The experimental results demonstrate that the THz detector array, configured according to the proposed design scheme, exhibits a maximum Rv of 55 kV W−1 and a minimum noise equivalent power of 52.4 pW Hz1/2 at a single detector pixel operating within the 0.37 THz band.
- 21 November 2024
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 39 (12) , 125018
CMOS dual-band terahertz on-chip antenna array and detector design
In this paper, in response to the limitations of conventional single-pixel terahertz (THz) detectors in detecting a single frequency band and having a low imaging resolution. A dual-band high responsivity (Rv) array detector scheme is proposed. Includes dual-band high-gain on-chip antenna, matching circuit, dual-band self-mixing receiver circuit and integrated voltage amplifier. The proposed on-chip antenna uses a multi-loop nested design based on the octagonal antenna to realize the dual-band high gain characteristics. In addition, the use of ‘cross-loop’ metal modules as ground plane isolation effectively reduces the electromagnetic interference between the units in the array and ensures the stable operation of the detector array. The matching circuit realizes the maximum power transmission of THz signals between the antenna and the receiving circuit, improved detector Rv. The integrated two-stage voltage amplifier is able to effectively amplify the signal output from the receiver circuit to further increase the detector response voltage. The designed detector is fabricated using 0.18 μm CMOS process. Simulation results show that the antenna has a maximum gain of 5.23 dBi in the 0.37 THz band and 6.77 dBi in the 0.76 THz band. The detector can detect in both 0.37 and 0.76 THz bands. The experimental results demonstrate that the THz detector array, configured according to the proposed design scheme, exhibits a maximum Rv of 55 kV W−1 and a minimum noise equivalent power of 52.4 pW Hz1/2 at a single detector pixel operating within the 0.37 THz band.
- Open Access
- 19 November 2021
- Published by Hindawi Limited in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 32 (2) , e22986
An antenna capable of harvesting radio frequency, vibration, and light energy based on piezoelectric and solar film materials
This article proposes a new type of antenna capable of harvesting radio frequency, vibration and light energy based on piezoelectric and solar film materials. The antenna is designed by using solar film and Polyvinylidene fluoride(PVDF) piezoelectric film as the medium. Due to the high dielectric constant of the antenna medium, the size of the energy harvesting antenna can be effectively reduced. A stacked circle patch was designed for the microstrip antenna, and the antenna size is 53 mm × 60 mm × 0.6 mm. In order to improve the conversion efficiency, the rectifier circuit is optimized, and the modal analysis of PVDF is carried out. Test results show that the bandwidth of the antenna is 2–3 GHz. When the antenna is 50 cm away from the signal emission source with 3 dBm at 2.4 GHz, the output voltage is 2.02 V; under 75 Hz vibration excitation, the output voltage and power can reach 1.5 V and 1.13 mW; when the light intensity is 100 mW/cm2, the output voltage is 1.42 V, the output voltage can reach 1.3 V.
- 19 November 2021
- Published by Hindawi Limited in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 32 (2) , e22986
Open AccessAn antenna capable of harvesting radio frequency, vibration, and light energy based on piezoelectric and solar film materials
This article proposes a new type of antenna capable of harvesting radio frequency, vibration and light energy based on piezoelectric and solar film materials. The antenna is designed by using solar film and Polyvinylidene fluoride(PVDF) piezoelectric film as the medium. Due to the high dielectric constant of the antenna medium, the size of the energy harvesting antenna can be effectively reduced. A stacked circle patch was designed for the microstrip antenna, and the antenna size is 53 mm × 60 mm × 0.6 mm. In order to improve the conversion efficiency, the rectifier circuit is optimized, and the modal analysis of PVDF is carried out. Test results show that the bandwidth of the antenna is 2–3 GHz. When the antenna is 50 cm away from the signal emission source with 3 dBm at 2.4 GHz, the output voltage is 2.02 V; under 75 Hz vibration excitation, the output voltage and power can reach 1.5 V and 1.13 mW; when the light intensity is 100 mW/cm2, the output voltage is 1.42 V, the output voltage can reach 1.3 V.
- 5 November 2009
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 45 (23) , 1148-1149
Circularly-polarised four rhombic loop antennas with high gain and broad beam
A four rhombic loop antenna for circular polarisation is proposed. This antenna has a high gain of about 9.7 dBi and a broad beam of more than 130° half power beam width. Four parasitic loops are added inside the original four loops to increase the axis ratio bandwidth. A broadband balun is incorporated into the antenna for impedance matching. Details of the antenna design and experimental results are presented.
- 5 November 2009
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 45 (23) , 1148-1149
Circularly-polarised four rhombic loop antennas with high gain and broad beam
A four rhombic loop antenna for circular polarisation is proposed. This antenna has a high gain of about 9.7 dBi and a broad beam of more than 130° half power beam width. Four parasitic loops are added inside the original four loops to increase the axis ratio bandwidth. A broadband balun is incorporated into the antenna for impedance matching. Details of the antenna design and experimental results are presented.