Ti Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ti Zhou has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Hai Zhou
School of Mechanical Engineering, Yancheng Institute of Technology, No. 1 Hope Avenue Middle Road, Yancheng 224051, People’s Republic of China
2 shared publications - Xi Wang
School of Mechanical Engineering, Yancheng Institute of Technology, Yancheng, China
2 shared publications He Liu
School of Mechanical Engineering, Yancheng Institute of Technology, No. 1 Hope Avenue Middle Road, Yancheng 224051, People’s Republic of China
1 shared publication- Weiguang Yang
Yancheng Institute of Technology, No. 1, Hope Avenue Middle Road, Yancheng City, Jiangsu Province, Yancheng, 224051, CHINA
1 shared publication - Weiguang Yang
School of Mechanical Engineering, Yancheng Institute of Technology, Yancheng 224051, People’s Republic of China
1 shared publication
Latest Publications
- Open Access
- 1 August 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (8) , 086502
Nano TiC particles modulate wear resistance and impact toughness of 40Cr alloy steel gradient-reinforced layer fabricated by laser melting deposition
Alloy steel components can be subjected to serious damage from a variety of conditions during the industrial production procedures, such as wear and fracture failure. Therefore, the preparation of gradient-reinforced layers on the surface of the alloy steel was considered an effective technique to improve the performance. Along these lines, a 40Cr alloy steel, which was commonly used in industry, was systematically investigated in this work. The nano TiC ceramic material was selected in the hard phase. In this work, continuous-wave laser was used to fabricate gradient reinforced layers, which provided a technical reference for the development of protective reinforcement layers for alloy steels with excellent mechanical properties. A dense structure was formed inside the nano TiC gradient reinforced layer, which has a lower friction coefficient (0.25) and wear loss weight (23 mg). The height of the surface material loss under a heavy load wear environment (187 μm) was lower than that of a bare 40Cr alloy steel sample (1116 μm). The impact energy of the nano TiC gradient reinforced layer (75.27 J cm−2) was higher than that of a bare 40Cr alloy steel sample (15.25 J cm−2). Both the wear behavior and impact toughness strengthening mechanism of the nano TiC gradient reinforced layer were revealed.
- 1 August 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (8) , 086502
Open AccessNano TiC particles modulate wear resistance and impact toughness of 40Cr alloy steel gradient-reinforced layer fabricated by laser melting deposition
Alloy steel components can be subjected to serious damage from a variety of conditions during the industrial production procedures, such as wear and fracture failure. Therefore, the preparation of gradient-reinforced layers on the surface of the alloy steel was considered an effective technique to improve the performance. Along these lines, a 40Cr alloy steel, which was commonly used in industry, was systematically investigated in this work. The nano TiC ceramic material was selected in the hard phase. In this work, continuous-wave laser was used to fabricate gradient reinforced layers, which provided a technical reference for the development of protective reinforcement layers for alloy steels with excellent mechanical properties. A dense structure was formed inside the nano TiC gradient reinforced layer, which has a lower friction coefficient (0.25) and wear loss weight (23 mg). The height of the surface material loss under a heavy load wear environment (187 μm) was lower than that of a bare 40Cr alloy steel sample (1116 μm). The impact energy of the nano TiC gradient reinforced layer (75.27 J cm−2) was higher than that of a bare 40Cr alloy steel sample (15.25 J cm−2). Both the wear behavior and impact toughness strengthening mechanism of the nano TiC gradient reinforced layer were revealed.
- Open Access
- 1 December 2021
- Published by IOP Publishing in Materials Research Express
- Vol. 8 (12) , 126521
Effect of nano TiC on microstructure and microhardness of composite additive manufacturing 316L stainless steel
The lower surface hardness limits the further application of 316 L stainless steel. In this study, selective laser melting (SLM)/laser metal deposition (LMD) composite additive manufacturing technology was used to prepare five kinds of 316L-nano-TiC cermet strengthening layers on the surface of 316L stainless steel, and to study the effect of nano-TiC particle content on the microstructure and the influence of microhardness. Use Laser microscope, scanning electron microscope (SEM), X-ray diffractometer (XRD) to analyze the structure, element distribution and phase composition of the strengthening layer. The hardness of the strengthened layer was analyzed using a Vickers micro-hardness tester. The study found that the composite SLM/LMD formed samples changed continuously from LMD forming to SLM forming, showing good metallurgical bonding. Diffusion of TiC particles was observed in the SLM strengthening layer, and TiC phase was detected in the strengthening layer. Compared with the 316L matrix, the microhardness of the strengthened layer is significantly improved. When 50 wt% TiC is added, the average hardness of the strengthened layer is 1.9 times that of the 316L matrix, and the highest is 408.9 HV. The results of this study show that the strengthening layer manufactured by composite additive materials can effectively improve the hardness of the 316L stainless steel matrix. As the content of nano-TiC in the preset powder increases, the microhardness of the strengthening layer first increases and then decreases, and the hardness of the 50wt% TiC strengthening layer is the highest. There are distributed nano-TiC particles in the structure of the strengthening layer, and the distribution of nano-TiC particles in the 50wt% TiC strengthening layer is more uniform than other samples. This research provides a new reference for the strengthening of 316L stainless steel through SLM/LMD composite additive manufacturing technology and the addition of nano-TiC particles.
- 1 December 2021
- Published by IOP Publishing in Materials Research Express
- Vol. 8 (12) , 126521
Open AccessEffect of nano TiC on microstructure and microhardness of composite additive manufacturing 316L stainless steel
The lower surface hardness limits the further application of 316 L stainless steel. In this study, selective laser melting (SLM)/laser metal deposition (LMD) composite additive manufacturing technology was used to prepare five kinds of 316L-nano-TiC cermet strengthening layers on the surface of 316L stainless steel, and to study the effect of nano-TiC particle content on the microstructure and the influence of microhardness. Use Laser microscope, scanning electron microscope (SEM), X-ray diffractometer (XRD) to analyze the structure, element distribution and phase composition of the strengthening layer. The hardness of the strengthened layer was analyzed using a Vickers micro-hardness tester. The study found that the composite SLM/LMD formed samples changed continuously from LMD forming to SLM forming, showing good metallurgical bonding. Diffusion of TiC particles was observed in the SLM strengthening layer, and TiC phase was detected in the strengthening layer. Compared with the 316L matrix, the microhardness of the strengthened layer is significantly improved. When 50 wt% TiC is added, the average hardness of the strengthened layer is 1.9 times that of the 316L matrix, and the highest is 408.9 HV. The results of this study show that the strengthening layer manufactured by composite additive materials can effectively improve the hardness of the 316L stainless steel matrix. As the content of nano-TiC in the preset powder increases, the microhardness of the strengthening layer first increases and then decreases, and the hardness of the 50wt% TiC strengthening layer is the highest. There are distributed nano-TiC particles in the structure of the strengthening layer, and the distribution of nano-TiC particles in the 50wt% TiC strengthening layer is more uniform than other samples. This research provides a new reference for the strengthening of 316L stainless steel through SLM/LMD composite additive manufacturing technology and the addition of nano-TiC particles.