Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Akin Akinci has a total of 52 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Corrosion Behavior of Shot-Peened Ti6Al4V Alloy Produced via Pressure-Assisted Sintering

    by Egemen Avcu, Eray Abakay, Yasemin Yıldıran Avcu, Emirhan Çalım, İdris Gökalp, Eleftherios Iakovakis, Funda Gül Koç, Ridvan Yamanoglu, Akın Akıncı, Mert Guney

    For the first time, the present study investigates the corrosion, surface, and subsurface properties of a shot-peened Ti6Al4V powder metallurgical alloy produced via pressure-assisted sintering. Shot peening yielded a fine-grained microstructure beneath the surface down to 100 microns, showing that it caused severe plastic deformation. XRD analysis revealed that the sizes of the crystallites in unpeened and shot-peened Ti6Al4V alloy samples were 48.59 nm and 27.26 nm, respectively, indicating a substantial reduction in crystallite size with shot peening. Cross-sectional hardness maps of shot-peened samples showed a work-hardened surface layer, indicating a ~17% increase in near-surface hardness relative to unpeened samples. Three-dimensional surface topographies showed that shot peening yielded uniform peaks and valleys, with a maximum peak height of 4.83 μm and depth of 6.56 μm. With shot peening, the corrosion potential shifted from −0.386 V to −0.175 V, showing that the passive layer developed faster and was more stable than the unpeened sample, improving corrosion resistance. As determined via XRD analysis, the increased grain refinement (i.e., the number of grain boundaries) and the subsequent accumulation of TiO2 and Al5Ti3V2 compounds through shot peening also suggested the effective formation of a protective passive layer. As demonstrated via electrochemical impedance spectroscopy, the formation of this passive film improved the corrosion resistance of the alloy. The findings will likely advance surface engineering and corrosion research, enabling safer and more productive shot peening in corrosion-critical applications.


  • Open Access

    Comparison of Tribological Behaviours of Nano SiO2 and ZrO2 Reinforced Polyester Matrix Composite Materials

    by Muhammet Ayçi̇çEk, Sedef Çakir Ayçi̇çEk, Neslihan Özsoy, Murat Özsoy, Akın AKINCI

    This paper aimed to examine and develop the tribological behaviour by adding nano reinforcements into the polyester matrix. Nanocomposite materials were obtained by adding nano-sized, 0.5%, 1%, 2% SiO2 and ZrO2 reinforcements to isophthalic polyester. These materials were mixed with mechanical and ultrasonic methods and poured into open moulds. The coefficient of friction and wear rates were obtained using the pin-on-disc test device. Optical and SEM surface images of the composites were examined. The experiments were conducted at room temperature and an average of 70% humidity. Tribological studies were made under a load of 2, 5, 10N and at a sliding speed of 0.5 and 0.1 m/s. It was seen that the nano reinforcements to the polyester matrix improved the tribological properties of the material.


  • Effect of cutting parameters on surface roughness of waste-filled composite at milling

    by Murat Ozsoy, Neslihan Ozsoy, Cumhur Kılıç, Akın Akıncı

    Industrial waste is a problem for companies as well as for the environment. In recent years, an alternative solution to this problem has been found – the use of waste in the production of new composite materials. It is not enough to produce only the composite. The machinability of the composite produced should also be investigated. This study obtained the new composite material using industrial waste produced by glass fibre-reinforced plastic pipes. The terephthalic resin was used as a matrix material. The waste powder was used as a filling material in the ratio of 30, 40 and 50% by weight compared to the matrix material. The machinability of produced composites was investigated according to three parameters with three levels. According to the experimental results, the optimum cutting parameters are obtained, depending on surface roughness.


  • Drilling of new vinyl ester matrixed waste-filled composite: statistical approach

    by Neslihan Ozsoy, Murat Ozsoy, Cihat Arda, Akın Akıncı

    Due to the increase in industrialisation and urbanisation in the world, pollution rates are increasing day by day. The world may become uninhabitable soon due to the increasing pollution rates. Thus, the issue of recycling waste generated during production has gained great importance, and many studies have been initiated on the recycling of waste materials. In this study, the waste generated during wet cutting of glass-fibre-reinforced polyester pipe produced by Subor Company was used as reinforcement in new vinyl ester matrixed composite material. To transform this developed composite material into an industrial product, some of its properties should be investigated. In this study, the optimisation of cutting parameters for drilling in composite materials was investigated. Four parameters (waste ratio, tool type, cutting speed, feed per tooth) were chosen. The cutting force was measured in the vertical direction during drilling. Analysis of variance (Anova) was done to find the effect of parameters. According to Anova results, feed per tooth was the most effective parameter on cutting force.

  • Open Access

    Using Foamed Polypropylene to Reduce Weight and Injection Molding Cycle Time in Toyota CH-R SUV Door Panel Production

    by Sedef Çakir, Muhammet Ayçi̇çEk, Neslihan Özsoy, Murat Özsoy, Mert Usta, Akın AKINCI

    In recent years, new technologies that encourage the use of cheaper and less raw materials have emerged in the automotive industry, with the increase in raw material costs as a result of the consumption of natural raw material resources and the occurrence of environmental problems. In this study, it was aimed to lighten the door panel and reduce the injection cycle time by using foam in the door panel production of Toyota CH-R model car. Injection parameters such as barrel temperature, injection speed, injection back pressure, holding pressure and holding time were changed. 1%, 1.5% and 2% by weight chemical foaming agent (CFA) was added to the polypropylene (PP) matrix. Approximately 4% lightening and 5.5 sec/shot injection cycle time reduction was achieved with the use of foaming agents. In addition, it was observed that cell morphologies, mechanical properties and sample weights changed due to changes in parameters and CFA ratio by weight.


  • Nano dolgulu polimer esaslı hidrofobik kaplamanın yüzey özelliklerinin incelenmesi

    by Cem Mehmetalioğlu, Uğursoy Olgun, Şaduman Şen, Uğur Şen, Akın Akıncı, Ebru Akcan, Arzu Özüyağlı

    Tr en Bu çalışmada ETİAL 171 numaralı alüminyum alaşımlı yüzeylere Trimethoxymethylsilane (MTMS), TetraethylorthoSilicate (TEOS), asetik asit ve saf suyun mol oranları sırasıyla 1:0,04:0,34:1,59 olacak şekilde sol-gel yöntemi kullanılarak kaplanmıştır. Kaplamalar titanyumdioksit (TiO2) nano toz katkısı kullanılarak üretilmiştir. Üretilen kaplamaların yüzey analizleri optik mikroskop, ıslatma açısı, kalınlık ölçümü cihazları kullanılarak ve cross-cut test kiti ile yapışma adezyonu belirlenmiştir. Islatma açısı 145,5° olan hidrofobik özelliklere sahip kaplama üretilmiştir. In this study ETIAL 171 to aluminum alloy surfaces were coated using the sol-gel process the molar ratio of Trimethoxymethylsilane (MTMS), TetraethylorthoSilicate (TEOS), acetic acid and pure water 1: 0.04: 0.34: 1.59. Coatings are manufactured using nano-additive powders titanium dioxide (TiO2). Optical microscope, contact angle, thickness measurement, cross cut test kit devices were used for tests. Coatings produced with hydrophobic properties.


  • Friction and Wear Behavior of Zinc Borate Filled Polycarbonate Composites

    by Akin Akinci

    The friction and wear performance of pure polycarbonate (PC) and 2.5, 5, 10, and 30% zinc borate-filled (by wt) PC composites were comparatively evaluated under dry sliding conditions. Wear tests were performed at room temperature under the loads of 5, 10, and 20 N and at the sliding speeds of 0.5, 1.0, and 1.5 m/s. The coefficients of friction of the composites were significantly influenced by an increase in zinc borate content. The friction coefficient of PC was decreased from 0.457 to 0.160 with an increase in zinc borate content, depending on applied loads and sliding speeds. The results showed that the wear rates of pure PC and zinc borate-filled composites decreased with an increase in loads. The wear rates of zinc borate-filled composites were significantly affected from zinc borate content. The wear rate of PC decreased from 9.4 × 10−5 to 6.8 × 10−6 mm3/m with an increase in zinc borate content depending on applied loads.


  • Dry sliding friction and wear behavior of self-lubricating wollastonite filled polycarbonate composites

    by Akin Akinci

    Purpose: – The purpose of this paper is to investigate the friction and wear performance of pure polycarbonate (PC) and 5-30 per cent wollastonite-filled (by weight) PC were comparatively evaluated under dry sliding conditions. Wear tests were carried out at room temperature under the loads of 5-20 N and at the sliding speeds of 0.5-1.5 m/s. Design/methodology/approach: – The microstructures of the wollastonite, pure PC and composites were examined by optical microscopy, scanning electron microscopy, energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) analysis. The friction and wear tests were realized using a pin-on-disk arrangement against the hardened AISI 4140 steel. Findings: – The result of this study indicated that the coefficients of friction wear rate of the materials were significantly influenced by an increase in wollastonite content. The friction coefficient of the PC was getting decreased from 0.457 to 0.198 with an increase in wollastonite content, depending on applied loads and sliding speeds. On the other hand, the results showed that the wear rates of pure PC and wollastonite-filled PCs decreased with an increase in loads. The wear rate of the PC decreased from 1.2 × 10−6 to 8.7 × 10−6 mm3/m with an increase in wollastonite content, depending on applied loads. Originality/value: – There are many reports which deal with the friction and wear performance of the polymers and polymer composites. However, the effect of wollastonite effect on tribological performance of PC has up to now not been extensively researched.