Vafa Marzang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Interests
Vafa Marzang has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Atif Iqbal
Department of Electrical Engineering, Qatar University, Doha, Qatar
5 shared publications - Shirazul Islam
Department of Electrical Engineering, Qatar University, Doha, Qatar
5 shared publications - Dong Cao
Department of Electrical and Computer Engineering, University of Dayton, Dayton, OH, USA
4 shared publications Hasan Mehrjerdi
Department of Electrical and Computer Engineering, George Washington University, Washington, DC, USA
3 shared publications- Peyman Alavi
School of Electrical Engineering and Computer Science, Penn State University, State College, PA, USA
3 shared publications - Seyed Majid Hashemzadeh
College of Electrical Engineering and New Energy, China Three Gorges University, Yichang, China
3 shared publications
Latest Publications
- Open Access
- 8 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 1225-1242
A Quadratic Non-Isolated High Step-Up Single-Input Dual-Output DC–DC Topology Based on Coupled Inductors with Low Input Current Ripple
This paper presents a new flexible high step-up DC-DC converter based on coupled inductors (CI), which operates as a Single-Input Dual-Output (SIDO) or Single-Input Single-Output (SISO) converter. The proposed SIDO (or SISO) topology includes two CI, two independent switches, four (three) diodes, and five (four) capacitors. The proposed converter produces high DC output voltages at a low value of duty cycles and low voltage stress across the power MOSFETs. The CIs' turn ratios give another freedom factor to increase the output voltages and decrease the switches' stress. The proposed converter ensures low input current ripple by designing the first coupled inductor's turn ratios. The converter's operation is analyzed at three zones of the switches' duty cycles, and the optimum zone is detected to enhance the converter's efficiency. Dynamic modeling, control strategy, and decoupling of dual output topology are thoroughly investigated. A comparison of the proposed converter with other SIDO/SISO topologies reported in the literature is provided, and the critical features of the proposed converter are highlighted. Finally, these features are proven based on a prototype at power rating and switching frequency of 500W and 50 kHz, in which the highest efficiency is measured at 200W and equals 96.4%.
- 8 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 1225-1242
Open AccessA Quadratic Non-Isolated High Step-Up Single-Input Dual-Output DC–DC Topology Based on Coupled Inductors with Low Input Current Ripple
This paper presents a new flexible high step-up DC-DC converter based on coupled inductors (CI), which operates as a Single-Input Dual-Output (SIDO) or Single-Input Single-Output (SISO) converter. The proposed SIDO (or SISO) topology includes two CI, two independent switches, four (three) diodes, and five (four) capacitors. The proposed converter produces high DC output voltages at a low value of duty cycles and low voltage stress across the power MOSFETs. The CIs' turn ratios give another freedom factor to increase the output voltages and decrease the switches' stress. The proposed converter ensures low input current ripple by designing the first coupled inductor's turn ratios. The converter's operation is analyzed at three zones of the switches' duty cycles, and the optimum zone is detected to enhance the converter's efficiency. Dynamic modeling, control strategy, and decoupling of dual output topology are thoroughly investigated. A comparison of the proposed converter with other SIDO/SISO topologies reported in the literature is provided, and the critical features of the proposed converter are highlighted. Finally, these features are proven based on a prototype at power rating and switching frequency of 500W and 50 kHz, in which the highest efficiency is measured at 200W and equals 96.4%.
- 7 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Consumer Electronics
- Vol. 71 (3) , 7947-7958
An Extendable High Step-Up Quadratic Boost Topology Having Low Voltage Stress on MOSFETs
A generalized quadratic boost converter topology has been proposed in the paper which offers large voltage gain with less voltage stresses at the switches. The proposed converter includes a basic unit cell having capacitors and diodes. By repeating the sequence of these units, the desired gain in voltage of the cascaded diode-capacitor-based quadratic boost converter (CDCQBC) is ensured with less voltage stress appearing at the switches. The converter’s cost becomes lower because the required switches is having lesser voltage rating. The available voltage gain of the converter makes CDCQBC a viable option to boost the voltage of renewable energy-based sources like solar photovoltaic (PV) sources, fuel cells, etc. The performance of this converter in continuous mode od conduction has been analyzed. Further, the effect of nonidealities of the elements included in CBHIC on efficiency and the voltage gain of this converter has been studied. The assessment of the proposed CDCQBC is done with various state-of-the-art quadratic boost converters reported in the literature and the main features of this converter are enlightened. To validate the findings, a lab prototype of the proposed converter having a power rating of 400 W has been developed and the experimental analysis are include
- 7 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Consumer Electronics
- Vol. 71 (3) , 7947-7958
An Extendable High Step-Up Quadratic Boost Topology Having Low Voltage Stress on MOSFETs
A generalized quadratic boost converter topology has been proposed in the paper which offers large voltage gain with less voltage stresses at the switches. The proposed converter includes a basic unit cell having capacitors and diodes. By repeating the sequence of these units, the desired gain in voltage of the cascaded diode-capacitor-based quadratic boost converter (CDCQBC) is ensured with less voltage stress appearing at the switches. The converter’s cost becomes lower because the required switches is having lesser voltage rating. The available voltage gain of the converter makes CDCQBC a viable option to boost the voltage of renewable energy-based sources like solar photovoltaic (PV) sources, fuel cells, etc. The performance of this converter in continuous mode od conduction has been analyzed. Further, the effect of nonidealities of the elements included in CBHIC on efficiency and the voltage gain of this converter has been studied. The assessment of the proposed CDCQBC is done with various state-of-the-art quadratic boost converters reported in the literature and the main features of this converter are enlightened. To validate the findings, a lab prototype of the proposed converter having a power rating of 400 W has been developed and the experimental analysis are include
- 10 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4617-4634
500-kW Resonant Switched-Capacitor Converter for 1600-V Electric Trucks and Electric Aircraft Powertrain Application
Hybrid/Battery power electric trucks or aircrafts draw more attention nowadays since they can eliminate greenhouse gases emission and other harmful gases to human health. For such a megawatt level electric power train design, a 1600 V system is more attractive due to the use of lighter, thinner wiring and potential much faster battery charging speeds, compared with the traditional 400 V or 800 V voltage bus. In this paper, a 500 kW three-phase interleaved resonant switched capacitor dc-dc converter is proposed and developed for such 1600 V applications. The operating principle is discussed, a detailed power loss analysis is provided, including MOSFETs losses, passive components losses, and busbar losses. An effective high-power testing method has also been proposed to validate the proposed converter’s performance at the rated voltage and rated current. Both of the simulation and experimental results are provided, indicating a peak efficiency of 99.1% and an efficiency of 98.7% at full load conditions of 500 kW hardware prototype.
- 10 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4617-4634
500-kW Resonant Switched-Capacitor Converter for 1600-V Electric Trucks and Electric Aircraft Powertrain Application
Hybrid/Battery power electric trucks or aircrafts draw more attention nowadays since they can eliminate greenhouse gases emission and other harmful gases to human health. For such a megawatt level electric power train design, a 1600 V system is more attractive due to the use of lighter, thinner wiring and potential much faster battery charging speeds, compared with the traditional 400 V or 800 V voltage bus. In this paper, a 500 kW three-phase interleaved resonant switched capacitor dc-dc converter is proposed and developed for such 1600 V applications. The operating principle is discussed, a detailed power loss analysis is provided, including MOSFETs losses, passive components losses, and busbar losses. An effective high-power testing method has also been proposed to validate the proposed converter’s performance at the rated voltage and rated current. Both of the simulation and experimental results are provided, indicating a peak efficiency of 99.1% and an efficiency of 98.7% at full load conditions of 500 kW hardware prototype.
- 4 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (2) , 1891-1904
A New Quadratic High Step-Up DC–DC Converter Based on Coupled Inductors for Renewable Energy Applications
This paper presents a high-step-up DC-DC topology. This circuit configuration yields a quadratic output voltage while maintaining low voltage stress on power MOSFETs. The configuration features a common ground connection among the input and output ports, with the sources of the switches directly linked to the ground. It has two switches, three diodes, four capacitors, and two coupled inductors. The first coupled inductor has three windings to increase voltage gain and limit input current ripple. The second one has two windings to increase voltage gain. Steady-state analysis is conducted to determine output voltage and voltage stress across power MOSFETs. The suggested topology’s key feature is its soft input current ripple, which is achieved using a coupled inductor configuration. A comparison section highlights its features compared to the state-of-the-art topologies reported in this paper. In addition, graphical voltage gain and voltage stress of power MOSFETs compared with other structures are added. The final step includes the development of a laboratory prototype, which operates under duty cycle variations of 0.3-0.6 for a wide input voltage range of 18-48 V. The prototype is tested for a maximum output power of 400W and a switching frequency of 50 kHz.
- 4 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (2) , 1891-1904
A New Quadratic High Step-Up DC–DC Converter Based on Coupled Inductors for Renewable Energy Applications
This paper presents a high-step-up DC-DC topology. This circuit configuration yields a quadratic output voltage while maintaining low voltage stress on power MOSFETs. The configuration features a common ground connection among the input and output ports, with the sources of the switches directly linked to the ground. It has two switches, three diodes, four capacitors, and two coupled inductors. The first coupled inductor has three windings to increase voltage gain and limit input current ripple. The second one has two windings to increase voltage gain. Steady-state analysis is conducted to determine output voltage and voltage stress across power MOSFETs. The suggested topology’s key feature is its soft input current ripple, which is achieved using a coupled inductor configuration. A comparison section highlights its features compared to the state-of-the-art topologies reported in this paper. In addition, graphical voltage gain and voltage stress of power MOSFETs compared with other structures are added. The final step includes the development of a laboratory prototype, which operates under duty cycle variations of 0.3-0.6 for a wide input voltage range of 18-48 V. The prototype is tested for a maximum output power of 400W and a switching frequency of 50 kHz.
- 2 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (1) , 1359-1375
A High Conversion Ratio Matrix Autotransformer Switched-Capacitor Converter for 48 V Datacenter Application
This article proposes a matrix autotransformer switched-capacitor dc–dc converter (MASC) that converts 48 to 3.2 V for datacenter applications. The proposed MASC is similar to the series capacitor buck with integrated inductors; however, it works at resonant mode to achieve zero voltage switching switching. The operating principle and the power losses of the proposed circuit including both of the autotransformer and semiconductor devices are analyzed. Compared with a switched-tank converter with the same conversion ratio, the power loss of semiconductor devices can be reduced by 68%. Furthermore, compared with an LLC converter with an isolated matrix transformer, the copper loss of the proposed matrix autotransformer can be reduced by 50%. Finally, a hardware prototype has been designed and developed, both simulation and experimental results have been provided to demonstrate the feasibility and validity of the proposed circuit.
- 2 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (1) , 1359-1375
A High Conversion Ratio Matrix Autotransformer Switched-Capacitor Converter for 48 V Datacenter Application
This article proposes a matrix autotransformer switched-capacitor dc–dc converter (MASC) that converts 48 to 3.2 V for datacenter applications. The proposed MASC is similar to the series capacitor buck with integrated inductors; however, it works at resonant mode to achieve zero voltage switching switching. The operating principle and the power losses of the proposed circuit including both of the autotransformer and semiconductor devices are analyzed. Compared with a switched-tank converter with the same conversion ratio, the power loss of semiconductor devices can be reduced by 68%. Furthermore, compared with an LLC converter with an isolated matrix transformer, the copper loss of the proposed matrix autotransformer can be reduced by 50%. Finally, a hardware prototype has been designed and developed, both simulation and experimental results have been provided to demonstrate the feasibility and validity of the proposed circuit.
- Open Access
- 15 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 89488-89505
Distributed Secondary Controller to Minimize Circulating Current Flowing Among Sources in DC Microgrid
In the islanded mode of operation of a DC microgrid, the main objective is to achieve proportional sharing of load power among sources and to maintain the source voltage within the specified limit. The droop control technique is widely used to achieve these objectives. Nevertheless, the performance of the traditional droop control technique becomes poor in the case of DC Microgrid including sources having unequal values of nominal voltages. The difference in nominal voltages arises due to errors in the measurement of the voltage feedback signal. The unequal values of nominal voltages lead to errors in the proportional sharing of the load current among the source converters. The mismatch in nominal voltages leads to a flow of circulating current among sources. To minimize this circulating current flowing among the sources, various distributed secondary controllers are suggested in the literature. However, these controllers require prior information of circulating current flowing among sources or accurate measurement of line parameters. Further, the applicability of these controllers is valid for the radial configuration of the DC microgrid. To resolve these issues, a distributed secondary controller is proposed in this paper which shifts the droop characteristics of the source parallel to the voltage axis. The proposed controller does not require prior information of circulating current and no estimation of line parameters. The proposed controller requires the evaluation of proportional current to minimize the circulating current. The proportional value of current for a given source is calculated using the formation of power ratings of sources and initial values of their droop gains. The proposed controller ensures the accurate sharing of the load current among source converters in case of a microgrid having sources of unequal capacity or communication link failure. Further, the voltage regulation is maintained within the defined limit. A small signal model is derived to show the effect of the variation of parameters of the proposed controller on the stability of the DC microgrid. The efficacy of the proposed controller is validated with the help of results capture using the Controller Hardware-in-Loop (CHIL) approach which includes a Real-Time Digital Simulator (RTDS) and Digital Signal Processor (DSP).
- 15 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 89488-89505
Open AccessDistributed Secondary Controller to Minimize Circulating Current Flowing Among Sources in DC Microgrid
In the islanded mode of operation of a DC microgrid, the main objective is to achieve proportional sharing of load power among sources and to maintain the source voltage within the specified limit. The droop control technique is widely used to achieve these objectives. Nevertheless, the performance of the traditional droop control technique becomes poor in the case of DC Microgrid including sources having unequal values of nominal voltages. The difference in nominal voltages arises due to errors in the measurement of the voltage feedback signal. The unequal values of nominal voltages lead to errors in the proportional sharing of the load current among the source converters. The mismatch in nominal voltages leads to a flow of circulating current among sources. To minimize this circulating current flowing among the sources, various distributed secondary controllers are suggested in the literature. However, these controllers require prior information of circulating current flowing among sources or accurate measurement of line parameters. Further, the applicability of these controllers is valid for the radial configuration of the DC microgrid. To resolve these issues, a distributed secondary controller is proposed in this paper which shifts the droop characteristics of the source parallel to the voltage axis. The proposed controller does not require prior information of circulating current and no estimation of line parameters. The proposed controller requires the evaluation of proportional current to minimize the circulating current. The proportional value of current for a given source is calculated using the formation of power ratings of sources and initial values of their droop gains. The proposed controller ensures the accurate sharing of the load current among source converters in case of a microgrid having sources of unequal capacity or communication link failure. Further, the voltage regulation is maintained within the defined limit. A small signal model is derived to show the effect of the variation of parameters of the proposed controller on the stability of the DC microgrid. The efficacy of the proposed controller is validated with the help of results capture using the Controller Hardware-in-Loop (CHIL) approach which includes a Real-Time Digital Simulator (RTDS) and Digital Signal Processor (DSP).
- Open Access
- 10 October 2022
- Published by Elsevier in Energy Reports
- Vol. 8, 12699-12711
A high step-up DC–DC converter based on ASL and VMC for renewable energy applications
- 10 October 2022
- Published by Elsevier in Energy Reports
- Vol. 8, 12699-12711
Open AccessA high step-up DC–DC converter based on ASL and VMC for renewable energy applications
- 3 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (6) , 6899-6912
Analysis, Design, and Investigation of a Soft-Switched Buck Converter With High Efficiency
In this article, a new simple buck converter with zero voltage switching (ZVS) performance and almost zero output current ripple is proposed. The proposed structure's auxiliary circuit contains a capacitor and an inductor without any switches, which makes it possible to minimize the switching losses and eliminate other additional losses. The main power diode also turns off under zero current switching condition and the reverse recovery losses of the power diode is minimized. Eliminating the switching losses and the reverse recovery losses allows the converter to operate with high power efficiency, which makes it a good option for high power efficiency-required applications. In this article, five operational modes are explained. The design section includes the designing criteria of the components. Also, the efficiency analysis, control system for stabilizing the output voltage, and applying a variable inductor to ensure the soft-switching operation are analyzed. The comparison results are also discussed. Moreover, an experimental prototype of the proposed structure at 200 W output power and 75 kHz frequency is built to prove the above-mentioned advantages. Finally, the soft-switching waveforms are obtained for different output powers with various duty cycles and equal switching frequency to verify the ZVS performance of the converter at different loads and changes in input voltage and duty cycle.
- 3 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (6) , 6899-6912
Analysis, Design, and Investigation of a Soft-Switched Buck Converter With High Efficiency
In this article, a new simple buck converter with zero voltage switching (ZVS) performance and almost zero output current ripple is proposed. The proposed structure's auxiliary circuit contains a capacitor and an inductor without any switches, which makes it possible to minimize the switching losses and eliminate other additional losses. The main power diode also turns off under zero current switching condition and the reverse recovery losses of the power diode is minimized. Eliminating the switching losses and the reverse recovery losses allows the converter to operate with high power efficiency, which makes it a good option for high power efficiency-required applications. In this article, five operational modes are explained. The design section includes the designing criteria of the components. Also, the efficiency analysis, control system for stabilizing the output voltage, and applying a variable inductor to ensure the soft-switching operation are analyzed. The comparison results are also discussed. Moreover, an experimental prototype of the proposed structure at 200 W output power and 75 kHz frequency is built to prove the above-mentioned advantages. Finally, the soft-switching waveforms are obtained for different output powers with various duty cycles and equal switching frequency to verify the ZVS performance of the converter at different loads and changes in input voltage and duty cycle.
- 3 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (11) , 11023-11034
An Ultra High Step-Up Dual-Input Single-Output DC–DC Converter Based on Coupled Inductor
This article introduces a new coupled inductor based dual-input ultra-high step-up dc–dc converter with a high voltage conversion ratio, low voltage stress across semiconductor components, and high efficiency features. The coupled inductor and voltage multiplier circuit (VMC) techniques have been utilized to enhance the voltage gain. The blocking voltages of power switches are clamped by VMC at low values and can be controlled via the turn ratio of the coupled inductors that decreases the voltage rate of power switches and converter's cost. The presented dual-input structure can transfer power to the load from two independent voltage sources. Besides, the inputs and output ports are common ground, which can reduce the electromagnetic interference influences. Operation modes delineation, steady-state analysis, and comparison section are provided for describing the proposed structure performance. Finally, to confirm the effectiveness of the presented topology, experimental waveforms with a 200 W output power at 50 kHz switching frequency are presented.
- 3 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (11) , 11023-11034
An Ultra High Step-Up Dual-Input Single-Output DC–DC Converter Based on Coupled Inductor
This article introduces a new coupled inductor based dual-input ultra-high step-up dc–dc converter with a high voltage conversion ratio, low voltage stress across semiconductor components, and high efficiency features. The coupled inductor and voltage multiplier circuit (VMC) techniques have been utilized to enhance the voltage gain. The blocking voltages of power switches are clamped by VMC at low values and can be controlled via the turn ratio of the coupled inductors that decreases the voltage rate of power switches and converter's cost. The presented dual-input structure can transfer power to the load from two independent voltage sources. Besides, the inputs and output ports are common ground, which can reduce the electromagnetic interference influences. Operation modes delineation, steady-state analysis, and comparison section are provided for describing the proposed structure performance. Finally, to confirm the effectiveness of the presented topology, experimental waveforms with a 200 W output power at 50 kHz switching frequency are presented.