Zhe Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhe Zhao has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
Xiumin Yu
4 shared publicationsDecheng Li
Jilin University (JLU) - State Key Laboratory of Automotive Simulation and Control
3 shared publicationsPing Sun
3 shared publicationsTianqi Wang
3 shared publicationsWeibo Shi
3 shared publicationsYaodong Du
3 shared publications
Latest Publications
- Open Access
- 12 May 2026
- Published by Elsevier in SSRN Electronic Journal
Numerical and Experimental Study on Combustion and Emission Characteristics of Bio-ethanol/Gasoline/HHO Compound Supply Engine
At present, although bio-ethanol has become a widely used renewable energy source, it is still unable to fully replace fossil fuels in power systems. The key issue lies in the fact that its high latent heat of vaporization significantly deteriorates the combustion environment within the cylinder; however, the blended combustion of hydrogen-based fuels holds promise for resolving this critical issue. This paper presents simulation and experimental studies conducted on a gasoline port injection + bio-ethanol direct injection + HHO negative pressure inhalation (GPI+BEDI+HNPI) engine. The study investigates the optimizing effects of different fuel supply strategy coupling schemes (BEDIr, BEDIT, HNPIv) on the engine’s combustion and emission characteristics. The results indicate that earlier BEDIT and HNPI coupling can effectively mitigate the negative effects of a larger BEDIr on engine power performance, the combustion process, and combustion stability, while also improving the engine’s tolerance to a larger BEDIr. While HNPI can effectively cut HC and CO emissions, it results in a rise in NOx emissions. Increasing the BEDIr helps mitigate this issue. Overall, the fuel supply strategy “HNPIv = 16 L/min + BEDIr = 60% + 300°CA BTDC ≤ BEDIT ≤ 350°CA BTDC” enables the engine to achieve relatively ideal emission levels while maintaining combustion characteristics.
- 12 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNumerical and Experimental Study on Combustion and Emission Characteristics of Bio-ethanol/Gasoline/HHO Compound Supply Engine
At present, although bio-ethanol has become a widely used renewable energy source, it is still unable to fully replace fossil fuels in power systems. The key issue lies in the fact that its high latent heat of vaporization significantly deteriorates the combustion environment within the cylinder; however, the blended combustion of hydrogen-based fuels holds promise for resolving this critical issue. This paper presents simulation and experimental studies conducted on a gasoline port injection + bio-ethanol direct injection + HHO negative pressure inhalation (GPI+BEDI+HNPI) engine. The study investigates the optimizing effects of different fuel supply strategy coupling schemes (BEDIr, BEDIT, HNPIv) on the engine’s combustion and emission characteristics. The results indicate that earlier BEDIT and HNPI coupling can effectively mitigate the negative effects of a larger BEDIr on engine power performance, the combustion process, and combustion stability, while also improving the engine’s tolerance to a larger BEDIr. While HNPI can effectively cut HC and CO emissions, it results in a rise in NOx emissions. Increasing the BEDIr helps mitigate this issue. Overall, the fuel supply strategy “HNPIv = 16 L/min + BEDIr = 60% + 300°CA BTDC ≤ BEDIT ≤ 350°CA BTDC” enables the engine to achieve relatively ideal emission levels while maintaining combustion characteristics.
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Study on the Effect of Secondary Injection on the Combustion and Emission of N-Butanol Engine
N-butanol, as a biological alternative fuel containing oxygen, has similar physical and chemical properties to gasoline, and has a wide range of sources, which has attracted more and more attention and research. Direct injection technology has been widely used in the field of internal combustion engine due to its advantages of flexibility and control ability. In this paper, the secondary injection of n-butanol engine under the mode of in-cylinder direct injection is discussed to organize the stratified combustion of the mixture, optimize the combustion to improve the thermal efficiency and reduce the emission. A 4-cylinder four-stroke spark ignition(SI) engine was selected to carry out the secondary injection experiment of n-butanol under the excess air ratio(λ) of 1, engine speed of 1500r/min, and low load, and the variables were the second injection ratio and timing. The results show that the secondary injection of n-butanol can achieve stratified combustion of the mixture, but only at a specific second injection timing such as 100°CA BTDC or 125°CA BTDC the combustion effect is the best, small second injection ratio can optimize combustion, improve BTE, reduce HC and CO emissions. When the second injection ratio is greater than 60%, it results in incomplete fuel combustion, a 3% to 4% reduction in thermal efficiency and an increase in emissions. Coefficient of variations(COV) was increased by secondary injection, but the effect was insignificant in small injection ratio, and it will increase with the increase of second injection ratio.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessStudy on the Effect of Secondary Injection on the Combustion and Emission of N-Butanol Engine
N-butanol, as a biological alternative fuel containing oxygen, has similar physical and chemical properties to gasoline, and has a wide range of sources, which has attracted more and more attention and research. Direct injection technology has been widely used in the field of internal combustion engine due to its advantages of flexibility and control ability. In this paper, the secondary injection of n-butanol engine under the mode of in-cylinder direct injection is discussed to organize the stratified combustion of the mixture, optimize the combustion to improve the thermal efficiency and reduce the emission. A 4-cylinder four-stroke spark ignition(SI) engine was selected to carry out the secondary injection experiment of n-butanol under the excess air ratio(λ) of 1, engine speed of 1500r/min, and low load, and the variables were the second injection ratio and timing. The results show that the secondary injection of n-butanol can achieve stratified combustion of the mixture, but only at a specific second injection timing such as 100°CA BTDC or 125°CA BTDC the combustion effect is the best, small second injection ratio can optimize combustion, improve BTE, reduce HC and CO emissions. When the second injection ratio is greater than 60%, it results in incomplete fuel combustion, a 3% to 4% reduction in thermal efficiency and an increase in emissions. Coefficient of variations(COV) was increased by secondary injection, but the effect was insignificant in small injection ratio, and it will increase with the increase of second injection ratio.
- 1 January 2022
- Published by Elsevier in Journal of Cleaner Production
- Vol. 331
Experimental study on combustion and emission of an SI engine with ethanol /gasoline combined injection and EGR
- 1 January 2022
- Published by Elsevier in Journal of Cleaner Production
- Vol. 331
Experimental study on combustion and emission of an SI engine with ethanol /gasoline combined injection and EGR
- Open Access
- 20 September 2021
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 6 (39) , 25749-25761
Effects of Water Ratio in Hydrous Ethanol on the Combustion and Emissions of a Hydrous Ethanol/Gasoline Combined Injection Engine under Different Excess Air Ratios
Ethanol is usually combined with gasoline to manufacture ethanol–gasoline with excellent combustion characteristics. However, extracting water from hydrous ethanol to manufacture anhydrous ethanol consumed much energy, which increases the production cost of ethanol–gasoline. Many researchers have studied the combustion and emissions of hydrous ethanol–gasoline to explore the application of hydrous ethanol–gasoline as the fuel for spark-ignition engines. Most previous studies changed the hydrous ethanol ratio with fixed purity in hydrous ethanol–gasoline to study the effects of hydrous ethanol. Different from previous studies, this paper studied the effects of water ratio (Wr) in hydrous ethanol on the combustion and emissions of a hydrous ethanol/gasoline combined injection engine under different excess air ratio (λ) values. The ratios of ethanol and gasoline keep constant, while the purity of hydrous ethanol changes during the research. The experiment adopted the combined injection mode with hydrous ethanol direct injection plus gasoline port injection; the direct injection ratio was 20%. The experiment set three λ (0.9, 1, and 1.2) and five Wrs (0, 5, 10, 15, and 20%). The test engine’s speed was 1500 rpm, and the intake manifold absolute pressure was 48 kPa. Results showed that water inhibited combustion, prolonged CA 0-10 and CA 10-90, reduced Pmax and Tmax, and delayed APmax; larger λ made the deterioration on combustion more obvious, and the smaller λ had a larger tolerance to water. Water could increase torque and improve emissions, but different parameters corresponded to different optimal Wrs. For torque, the optimal Wr was 5%. For HC emissions, the optimal Wr was 0%; for CO emissions, the optimal value was 5%; and for NOx emissions, the best value was 20%. The best Wr was 10% for particle number (PN) emissions. Under the optimal Wr condition, when λ values were 0.9, 1, and 1.2, compared with pure gasoline, the torque increased by 7.5, 5.54, and 5.31%; HC emissions decreased by 21.37, 23.43, and 26.58%; NOx emissions decreased by 4.26, 11.47, and 12.55%; CO emissions decreased by 17.51, 34.56, −50%; and the total PN emissions decreased by 87.64, 89.64, and 76.07%.
- 20 September 2021
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 6 (39) , 25749-25761
Open AccessEffects of Water Ratio in Hydrous Ethanol on the Combustion and Emissions of a Hydrous Ethanol/Gasoline Combined Injection Engine under Different Excess Air Ratios
Ethanol is usually combined with gasoline to manufacture ethanol–gasoline with excellent combustion characteristics. However, extracting water from hydrous ethanol to manufacture anhydrous ethanol consumed much energy, which increases the production cost of ethanol–gasoline. Many researchers have studied the combustion and emissions of hydrous ethanol–gasoline to explore the application of hydrous ethanol–gasoline as the fuel for spark-ignition engines. Most previous studies changed the hydrous ethanol ratio with fixed purity in hydrous ethanol–gasoline to study the effects of hydrous ethanol. Different from previous studies, this paper studied the effects of water ratio (Wr) in hydrous ethanol on the combustion and emissions of a hydrous ethanol/gasoline combined injection engine under different excess air ratio (λ) values. The ratios of ethanol and gasoline keep constant, while the purity of hydrous ethanol changes during the research. The experiment adopted the combined injection mode with hydrous ethanol direct injection plus gasoline port injection; the direct injection ratio was 20%. The experiment set three λ (0.9, 1, and 1.2) and five Wrs (0, 5, 10, 15, and 20%). The test engine’s speed was 1500 rpm, and the intake manifold absolute pressure was 48 kPa. Results showed that water inhibited combustion, prolonged CA 0-10 and CA 10-90, reduced Pmax and Tmax, and delayed APmax; larger λ made the deterioration on combustion more obvious, and the smaller λ had a larger tolerance to water. Water could increase torque and improve emissions, but different parameters corresponded to different optimal Wrs. For torque, the optimal Wr was 5%. For HC emissions, the optimal Wr was 0%; for CO emissions, the optimal value was 5%; and for NOx emissions, the best value was 20%. The best Wr was 10% for particle number (PN) emissions. Under the optimal Wr condition, when λ values were 0.9, 1, and 1.2, compared with pure gasoline, the torque increased by 7.5, 5.54, and 5.31%; HC emissions decreased by 21.37, 23.43, and 26.58%; NOx emissions decreased by 4.26, 11.47, and 12.55%; CO emissions decreased by 17.51, 34.56, −50%; and the total PN emissions decreased by 87.64, 89.64, and 76.07%.