Nabarun Biswas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nabarun Biswas has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Prasun Chakraborti
Mechanical Engineering Department, National Institute of Technology Agartala, Agartala, Tripura, India
3 shared publications- Suman Kumar Mandal
NIT Agartala
3 shared publications - Biplab Bhattacharjee
Affiliation Department of Mechanical Engineering, Faculty of Engineering and Technology, SRM Institute of Science and Technology, Chennai, TamilNadu, India
2 shared publications Kishan Choudhuri
NIT Agartala
2 shared publications- Srijit Biswas
NIT Agartala
2 shared publications - Ankuran Saha
National Institute of Technology Agartala, Barjala
1 shared publication
Latest Publications
- 13 April 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 238 (10) , 1187-1197
Evaluation of the performance characteristics of aerostatic bearing with porous alumina (Al2O3) membrane using theoretical and experimental methods
Instruments with high levels of precision commonly use aerostatic bearings. Moreover, the use of porous (Al2O3 membrane) material validates that the pressure is spread uniformly throughout the air film region. The impression of applied load on the thickness of the air film of the aerostatic bearings was evaluated using a certain experimental technique. As the applied load rises, the thickness of the air film expands, and as the compressive stress rises, it contracts. The theoretical model parameters were set using the experimental stipulations. It was discovered that the theoretical model and the experimental data were consistent. The pressure gradient induced in the air film and the air bearings’ capacity for carrying loads were calculated using a theoretical simulation. The results of theoretical modeling and experimental comparison of the different characteristics of porous (Al2O3 membrane) aerostatic bearings based on stiffness and load-carrying capacity are graphically illustrated in this study. Porous aerostatic bearings with Al2O3 membranes have a number of potential applications, including high-speed spindles, precision instruments, microelectromechanical systems, vacuum pumps, cryogenic applications, etc.
- 13 April 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 238 (10) , 1187-1197
Evaluation of the performance characteristics of aerostatic bearing with porous alumina (Al2O3) membrane using theoretical and experimental methods
Instruments with high levels of precision commonly use aerostatic bearings. Moreover, the use of porous (Al2O3 membrane) material validates that the pressure is spread uniformly throughout the air film region. The impression of applied load on the thickness of the air film of the aerostatic bearings was evaluated using a certain experimental technique. As the applied load rises, the thickness of the air film expands, and as the compressive stress rises, it contracts. The theoretical model parameters were set using the experimental stipulations. It was discovered that the theoretical model and the experimental data were consistent. The pressure gradient induced in the air film and the air bearings’ capacity for carrying loads were calculated using a theoretical simulation. The results of theoretical modeling and experimental comparison of the different characteristics of porous (Al2O3 membrane) aerostatic bearings based on stiffness and load-carrying capacity are graphically illustrated in this study. Porous aerostatic bearings with Al2O3 membranes have a number of potential applications, including high-speed spindles, precision instruments, microelectromechanical systems, vacuum pumps, cryogenic applications, etc.
- 18 October 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 239 (4) , 2001-2011
Parametric optimisation on the performance of the journal bearing using Taguchi approach
Hydrodynamic journal bearings are widely used to support high-speed rotating equipment due to their excellent strength and load-bearing capacity. Therefore, bearings are essential mechanical elements to improve the quality of rotating equipment. Bearing performance depends on various factors but pressure and frictional torque plays a vital role in load carrying capacity of bearing. In this present work, both experimental and analytical approach of a typical journal bearing has been carried out to determine the optimal performance of the bearing. Taguchi-based optimisation method has been proposed for journal bearing. Taguchi L27 orthogonal array has been planned to study peak pressure and frictional torque with three input parameters speed, load and viscosity index. The result shows that loading criterion influences much on performance of bearing. The experimental data is obtained from a journal bearing test rig and the analytical data are generated by MINITAB 18. From the experiment, it can be confirmed that speed – 2000 rpm, load – 600 N and viscosity index – 150 are the ideal process parameters for lower peak pressure and less frictional torque.
- 18 October 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 239 (4) , 2001-2011
Parametric optimisation on the performance of the journal bearing using Taguchi approach
Hydrodynamic journal bearings are widely used to support high-speed rotating equipment due to their excellent strength and load-bearing capacity. Therefore, bearings are essential mechanical elements to improve the quality of rotating equipment. Bearing performance depends on various factors but pressure and frictional torque plays a vital role in load carrying capacity of bearing. In this present work, both experimental and analytical approach of a typical journal bearing has been carried out to determine the optimal performance of the bearing. Taguchi-based optimisation method has been proposed for journal bearing. Taguchi L27 orthogonal array has been planned to study peak pressure and frictional torque with three input parameters speed, load and viscosity index. The result shows that loading criterion influences much on performance of bearing. The experimental data is obtained from a journal bearing test rig and the analytical data are generated by MINITAB 18. From the experiment, it can be confirmed that speed – 2000 rpm, load – 600 N and viscosity index – 150 are the ideal process parameters for lower peak pressure and less frictional torque.
- Open Access
- 1 February 2023
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1110 (1) , 012073
CFD Analysis of water-based slipper bearing
The leakage across the slipper land of a swashplate type axial piston pump is inherent in almost all the commercially available designs. This occurs due to the back flow of each piston through its orifice and gap between the slipper and swashplate. This flow phenomenon is studied in detail in the present work. To optimize pump performance with a reduced leakage, it is critical to know the fluid dynamics within the pump passages. In this paper, a three-dimensional CFD methodology has been created and employed to predict the pump performance in terms of pressure field, velocity vectors, and the flow pattern to understand pump flow. The methodology is established in the commercially available code ANSYS FLUENT 16.0 which supports the existence of complicated geometry in the form of narrow orifices and gaps between rotating and stationary walls. Slipper leakages, velocity and pressure fields are computed using simple algorithm approach at different designs and operating conditions. Experimental data of the film thickness is used in the present simulation. The effect of different piston pressure, slipper velocity, oil viscosity, slipper orifice diameter and slipper pool inner diameter is studied. Investigations of this kind may help for the development and design of slippers.
- 1 February 2023
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1110 (1) , 012073
Open AccessCFD Analysis of water-based slipper bearing
The leakage across the slipper land of a swashplate type axial piston pump is inherent in almost all the commercially available designs. This occurs due to the back flow of each piston through its orifice and gap between the slipper and swashplate. This flow phenomenon is studied in detail in the present work. To optimize pump performance with a reduced leakage, it is critical to know the fluid dynamics within the pump passages. In this paper, a three-dimensional CFD methodology has been created and employed to predict the pump performance in terms of pressure field, velocity vectors, and the flow pattern to understand pump flow. The methodology is established in the commercially available code ANSYS FLUENT 16.0 which supports the existence of complicated geometry in the form of narrow orifices and gaps between rotating and stationary walls. Slipper leakages, velocity and pressure fields are computed using simple algorithm approach at different designs and operating conditions. Experimental data of the film thickness is used in the present simulation. The effect of different piston pressure, slipper velocity, oil viscosity, slipper orifice diameter and slipper pool inner diameter is studied. Investigations of this kind may help for the development and design of slippers.
- 6 December 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 236 (3) , 1229-1238
Application of nanofluids on various performance characteristics of hydrodynamic journal bearing—A review
Bearings are designed to support the loads normally applied to the shaft, while allowing relative movement between two machine elements. Journal or sliding bearings are perhaps the most well-known sorts of hydrodynamic bearings. The journal bearings contain no rolling elements and these bearings’ design and construction are simple, but their operation and theory are complex. Due to this and other advantages, journal bearings are much preferred in engineering applications. Simultaneously, the associated research and development have resulted in reasonable progress and therefore, a thorough review of these is earnestly felt. The static and dynamic characteristics of hydrodynamic journal bearings mainly depend on the lubricant viscosity and other factors such as load, speed, friction, and eccentricity. The review analysis focused on nanofluid lubricated hydrodynamic journal bearings are one of the rare topics of interest among tribologists. The use of a nanofluid as a lubricant is very important as it significantly improves the performance characteristics of the investigated bearing. The aggregation of nanoparticles in lubricants available commercially can cause a sharp increase in pressure drop and significantly improve the lubricant viscosity, which leads to an increase in load-carrying capacity. The tribological properties of various lubricants/base oils can be augmented by nanoparticles containing the lubricant. Studies have shown that compared to other conventional engine oils the load-carrying capacity is increased with nanoparticles containing the lubricant.
- 6 December 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 236 (3) , 1229-1238
Application of nanofluids on various performance characteristics of hydrodynamic journal bearing—A review
Bearings are designed to support the loads normally applied to the shaft, while allowing relative movement between two machine elements. Journal or sliding bearings are perhaps the most well-known sorts of hydrodynamic bearings. The journal bearings contain no rolling elements and these bearings’ design and construction are simple, but their operation and theory are complex. Due to this and other advantages, journal bearings are much preferred in engineering applications. Simultaneously, the associated research and development have resulted in reasonable progress and therefore, a thorough review of these is earnestly felt. The static and dynamic characteristics of hydrodynamic journal bearings mainly depend on the lubricant viscosity and other factors such as load, speed, friction, and eccentricity. The review analysis focused on nanofluid lubricated hydrodynamic journal bearings are one of the rare topics of interest among tribologists. The use of a nanofluid as a lubricant is very important as it significantly improves the performance characteristics of the investigated bearing. The aggregation of nanoparticles in lubricants available commercially can cause a sharp increase in pressure drop and significantly improve the lubricant viscosity, which leads to an increase in load-carrying capacity. The tribological properties of various lubricants/base oils can be augmented by nanoparticles containing the lubricant. Studies have shown that compared to other conventional engine oils the load-carrying capacity is increased with nanoparticles containing the lubricant.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1754, 030002
Performance & stability analysis of a three lobe journal bearing with varying parameters: Experiments and analysis
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1754, 030002
Performance & stability analysis of a three lobe journal bearing with varying parameters: Experiments and analysis