Raúl Cervera-Marín
Raúl Cervera-Marín has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Carlos Alcaide
TEAM, Universitat Politcnica de Valncia, Valencia, Spain
7 shared publications - Vicente Enrique Boria
Universitat Politècnica de València
7 shared publications - Miguel Rodríguez Jodar
ESA-VSC European High Power RF Space Laboratory, Valencia, Spain
6 shared publications - Pablo Soto
TEAM, Universitat Politcnica de Valncia, Valencia, Spain
6 shared publications - César Miquel España
European Space Research and Technology Centre of the European Space Agency (ESTEC-ESA), Noordwijk, AG, The Netherlands
5 shared publications - David Raboso
European Space Agency, Noordwijk, The Netherlands
5 shared publications
Latest Publications
- Open Access
- 20 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (6) , 5422-5434
Accurate Multipactor Analysis of Passive Bandpass Waveguide Filters Under Modulated Signal Excitation
Multipactor is a key effect in satellite communication hardware, which can ultimately limit their power-handling capability and the overall system performance. For this reason, the industry is interested in predicting the multipactor power threshold during the design phase of on-board payloads. Although the techniques for computing this threshold for continuous-wave (CW) excitation are nowadays mature, its determination under modulated signal operation is still a complex task. For narrowband passive devices, the problem is even more intricate as the frequency dependence of the component response must also be taken into account. To address this scenario, the so-called sliced-spectrum multipactor analysis (SSMA) method is proposed in this article. This technique operates by segmenting the spectrum of the modulated signal into multiple spectral slices and then representing the signal as the sum of different carriers modulated by each of the segmented slices. This operation scheme enables the use of each spectral slice of the steady-state electromagnetic (EM) fields at its corresponding carrier frequency. As a result, an accurate and efficient multipactor analysis technique is developed. This new approach is rigorously validated using bandpass waveguide filter samples, allowing us to benchmark the multipactor power thresholds predicted by the SSMA technique against those provided by measurements and available state-of-the-art codes.
- 20 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (6) , 5422-5434
Open AccessAccurate Multipactor Analysis of Passive Bandpass Waveguide Filters Under Modulated Signal Excitation
Multipactor is a key effect in satellite communication hardware, which can ultimately limit their power-handling capability and the overall system performance. For this reason, the industry is interested in predicting the multipactor power threshold during the design phase of on-board payloads. Although the techniques for computing this threshold for continuous-wave (CW) excitation are nowadays mature, its determination under modulated signal operation is still a complex task. For narrowband passive devices, the problem is even more intricate as the frequency dependence of the component response must also be taken into account. To address this scenario, the so-called sliced-spectrum multipactor analysis (SSMA) method is proposed in this article. This technique operates by segmenting the spectrum of the modulated signal into multiple spectral slices and then representing the signal as the sum of different carriers modulated by each of the segmented slices. This operation scheme enables the use of each spectral slice of the steady-state electromagnetic (EM) fields at its corresponding carrier frequency. As a result, an accurate and efficient multipactor analysis technique is developed. This new approach is rigorously validated using bandpass waveguide filter samples, allowing us to benchmark the multipactor power thresholds predicted by the SSMA technique against those provided by measurements and available state-of-the-art codes.
- Open Access
- 13 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (10) , 5662-5669
Impact of Distortion on the Multipactor Threshold for Dual Carrier Digitally Modulated Signals
Multipactor under digitally modulated signals is a field of growing interest in the space industry. The need to operate with higher powers arises from the industry demand to increase data throughput, enabled by advances in space-born amplifiers. However, this often leads to signal distortion, which may alter the multipactor threshold measured in laboratory conditions. This work aims to characterize, through the combination of experimental tests and numerical simulations, how distortion affects the multipactor performance of microwave devices excited by modulated signals. To this end, several dual carrier modulated signals with different distortion levels are digitally created, simulated, and tested on the same multipactor sample. When the simulation configuration matches the laboratory conditions, an excellent degree of accuracy is reported. However, simulations also demonstrate that the nonzero time response of the sensors may play a crucial role in determining the measured threshold, suggesting that laboratory detectors may struggle to detect short-lived events. Numerical predictions also reveal how the thresholds linked to these events are affected by the degree of signal distortion.
- 13 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (10) , 5662-5669
Open AccessImpact of Distortion on the Multipactor Threshold for Dual Carrier Digitally Modulated Signals
Multipactor under digitally modulated signals is a field of growing interest in the space industry. The need to operate with higher powers arises from the industry demand to increase data throughput, enabled by advances in space-born amplifiers. However, this often leads to signal distortion, which may alter the multipactor threshold measured in laboratory conditions. This work aims to characterize, through the combination of experimental tests and numerical simulations, how distortion affects the multipactor performance of microwave devices excited by modulated signals. To this end, several dual carrier modulated signals with different distortion levels are digitally created, simulated, and tested on the same multipactor sample. When the simulation configuration matches the laboratory conditions, an excellent degree of accuracy is reported. However, simulations also demonstrate that the nonzero time response of the sensors may play a crucial role in determining the measured threshold, suggesting that laboratory detectors may struggle to detect short-lived events. Numerical predictions also reveal how the thresholds linked to these events are affected by the degree of signal distortion.
- Open Access
- 22 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (6) , 3177-3184
A Fast and Accurate Coarse Method for Multipactor Threshold Prediction of RF Filters Under Modulated Signal Excitation
Multipactor is a key high-power effect limiting the system performance for onboard satellite hardware. Although modern particle simulators admit arbitrary geometries and signals as inputs, their practical use is often limited to continuous-wave (CW) excitations. Unfortunately, the multipactor analysis for input-modulated signals normally leads to prohibitively large CPU times, as signal lengths are very large compared to the electron population’s evolution time. The Coarse Method is an elegant way of overcoming this limitation, providing a good estimate of the multipactor threshold in reduced CPU times. However, if the input signal is not preprocessed before being analyzed, the method is unable to account for the frequency dependence as it operates with electron dynamics information extracted at a single frequency, leading to biased predictions for narrowband samples as filters. This article proposes an extension to the original Coarse Method implementation by considering the sample response and the modulated signal spectral distribution to account for the frequency dependence. The resulting method is suitable for estimating the multipactor threshold of narrowband samples excited by modulated signals, while keeping the benefits in terms of simplicity, efficiency, and generality of the Coarse Method. The proposed approach is benchmarked against laboratory measurement results, as well as particle simulators and legacy Coarse Method predictions, revealing the advantages of the novel technique and its range of applications.
- 22 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (6) , 3177-3184
Open AccessA Fast and Accurate Coarse Method for Multipactor Threshold Prediction of RF Filters Under Modulated Signal Excitation
Multipactor is a key high-power effect limiting the system performance for onboard satellite hardware. Although modern particle simulators admit arbitrary geometries and signals as inputs, their practical use is often limited to continuous-wave (CW) excitations. Unfortunately, the multipactor analysis for input-modulated signals normally leads to prohibitively large CPU times, as signal lengths are very large compared to the electron population’s evolution time. The Coarse Method is an elegant way of overcoming this limitation, providing a good estimate of the multipactor threshold in reduced CPU times. However, if the input signal is not preprocessed before being analyzed, the method is unable to account for the frequency dependence as it operates with electron dynamics information extracted at a single frequency, leading to biased predictions for narrowband samples as filters. This article proposes an extension to the original Coarse Method implementation by considering the sample response and the modulated signal spectral distribution to account for the frequency dependence. The resulting method is suitable for estimating the multipactor threshold of narrowband samples excited by modulated signals, while keeping the benefits in terms of simplicity, efficiency, and generality of the Coarse Method. The proposed approach is benchmarked against laboratory measurement results, as well as particle simulators and legacy Coarse Method predictions, revealing the advantages of the novel technique and its range of applications.
- Open Access
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 5 (2) , 438-450
Multipactor Breakdown Threshold Estimation Based on Circuital Models and Particle Simulations for Multicarrier Signals in RF Filters
Multipactor is a harmful effect that may challenge the correct operation of satellite communication systems by limiting the system power-handling capability, and hence its overall performance. Therefore, the development of techniques for predicting the multipactor threshold is of great practical interest. For narrowband components, rough estimations can be obtained from experimental charts, normally resulting in conservative thresholds. More accurate predictions can be obtained with particle simulators, at the expense of a much higher computational effort. This study proposes an approach based on circuital models for swift and accurate multipactor threshold predictions, specifically addressing short-term discharges induced by multicarrier signals in narrowband samples. The use of reduced, but representative, electromagnetic (EM) models of the critical gap region is discussed in detail. Through the use of these models, it is possible to avoid simulating the complete structure, increasing the computational efficiency and enabling the fulfillment of the power requirements at early design stages. The proposed technique is validated through commercial particle simulators, showcasing its efficacy, efficiency, and key benefits.
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 5 (2) , 438-450
Open AccessMultipactor Breakdown Threshold Estimation Based on Circuital Models and Particle Simulations for Multicarrier Signals in RF Filters
Multipactor is a harmful effect that may challenge the correct operation of satellite communication systems by limiting the system power-handling capability, and hence its overall performance. Therefore, the development of techniques for predicting the multipactor threshold is of great practical interest. For narrowband components, rough estimations can be obtained from experimental charts, normally resulting in conservative thresholds. More accurate predictions can be obtained with particle simulators, at the expense of a much higher computational effort. This study proposes an approach based on circuital models for swift and accurate multipactor threshold predictions, specifically addressing short-term discharges induced by multicarrier signals in narrowband samples. The use of reduced, but representative, electromagnetic (EM) models of the critical gap region is discussed in detail. Through the use of these models, it is possible to avoid simulating the complete structure, increasing the computational efficiency and enabling the fulfillment of the power requirements at early design stages. The proposed technique is validated through commercial particle simulators, showcasing its efficacy, efficiency, and key benefits.
- Open Access
- 9 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (4) , 2638-2644
A Genetically Based Algorithm to Improve Execution Speed in Multipactor Simulations in Parallel-Plate Waveguides
This article presents an approach to enhance the convergence speed of Monte Carlo simulations for multipactor phenomena in parallel-plate geometries. Multipactor, a self-sustained electron discharge, may cause significantly harmful effects in electronic device operation. An adaptive genetic modification method is introduced to explore the parameter space of electron trajectories efficiently, leading to rapid identification of the critical combinations that induce population growth or decay. The proposed approach involves modifying key parameters, such as the initial phases and kinetic energies of individual particles, based on their performance in multipactor simulations. The reported results demonstrate a substantial improvement in convergence speed, achieving accurate results with fewer tracked particles. The adaptive genetic modification proves to be a promising technique for fast multipactor threshold predictions in parallel-plate configurations and has potential applications when analyzing electron-induced phenomena in a wide range of electronic systems.
- 9 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (4) , 2638-2644
Open AccessA Genetically Based Algorithm to Improve Execution Speed in Multipactor Simulations in Parallel-Plate Waveguides
This article presents an approach to enhance the convergence speed of Monte Carlo simulations for multipactor phenomena in parallel-plate geometries. Multipactor, a self-sustained electron discharge, may cause significantly harmful effects in electronic device operation. An adaptive genetic modification method is introduced to explore the parameter space of electron trajectories efficiently, leading to rapid identification of the critical combinations that induce population growth or decay. The proposed approach involves modifying key parameters, such as the initial phases and kinetic energies of individual particles, based on their performance in multipactor simulations. The reported results demonstrate a substantial improvement in convergence speed, achieving accurate results with fewer tracked particles. The adaptive genetic modification proves to be a promising technique for fast multipactor threshold predictions in parallel-plate configurations and has potential applications when analyzing electron-induced phenomena in a wide range of electronic systems.
- Open Access
- 23 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 2 (1) , 57-77
Multipactor Threshold Estimation Techniques Based on Circuit Models, Electromagnetic Fields, and Particle Simulators
Multipactor has become a keylimiting factor of the final performance of satellite communication systems, due to the increase in power levels and/or operating frequency bands. As a result, the critical components of these systems must meet demanding multipactor specifications which should be considered during the design process. This paper describes the different techniques available to predict the multipactor threshold power for radio frequency (RF) and microwave passive hardware under continuous wave (CW) excitation, from cumbersome particle simulations to fast approximate methods based on circuit models. All these techniques have been described and compared together for the first time, including also a detailed description of the configuration issues of commercial particle simulators required to obtain accurate multipactor threshold predictions. The techniques are applied to both wideband and narrowband application examples. The predictions have been compared with measured thresholds of manufactured samples obtained with a novel multipactor test bed, thus allowing to highlight the advantages and limitations of each technique and particle simulator. From this paper, it will be possible to choose the most suitable procedure (and an appropriate simulator, if needed) to obtain multipactor threshold prediction of passive hardware.
- 23 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 2 (1) , 57-77
Open AccessMultipactor Threshold Estimation Techniques Based on Circuit Models, Electromagnetic Fields, and Particle Simulators
Multipactor has become a keylimiting factor of the final performance of satellite communication systems, due to the increase in power levels and/or operating frequency bands. As a result, the critical components of these systems must meet demanding multipactor specifications which should be considered during the design process. This paper describes the different techniques available to predict the multipactor threshold power for radio frequency (RF) and microwave passive hardware under continuous wave (CW) excitation, from cumbersome particle simulations to fast approximate methods based on circuit models. All these techniques have been described and compared together for the first time, including also a detailed description of the configuration issues of commercial particle simulators required to obtain accurate multipactor threshold predictions. The techniques are applied to both wideband and narrowband application examples. The predictions have been compared with measured thresholds of manufactured samples obtained with a novel multipactor test bed, thus allowing to highlight the advantages and limitations of each technique and particle simulator. From this paper, it will be possible to choose the most suitable procedure (and an appropriate simulator, if needed) to obtain multipactor threshold prediction of passive hardware.
- Open Access
- 1 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (12) , 5429-5438
High Power RF Discharge Detection Technique Based on the In-Phase and Quadrature Signals
High power radio frequency (RF) breakdown testing is a subject of great relevance in the space industry, due to the increasing need of higher transmission power and smaller devices. This work presents a novel RF breakdown detection system, which monitors the same parameters as the microwave nulling system but with several advantages. Where microwave nulling--a de facto standard in RF breakdown testing--is narrowband and requires continuous tuning to keep its sensitivity, the proposed technique is broadband and maintains its performance for any RF signal. On top of that, defining the detection threshold is cumbersome due to the lack of an international standardized criterion. Small responses may appear in the detection system during the test and, sometimes, it is not possible to determine if these are an actual RF breakdown or random noise. This new detection system uses a larger analysis bandwidth, thus reducing the cases in which a small response is difficult to be classified. The proposed detection method represents a major step forward in high power testing as it runs without human intervention, warning the operator or decreasing the RF power automatically much faster than any human operator.
- 1 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (12) , 5429-5438
Open AccessHigh Power RF Discharge Detection Technique Based on the In-Phase and Quadrature Signals
High power radio frequency (RF) breakdown testing is a subject of great relevance in the space industry, due to the increasing need of higher transmission power and smaller devices. This work presents a novel RF breakdown detection system, which monitors the same parameters as the microwave nulling system but with several advantages. Where microwave nulling--a de facto standard in RF breakdown testing--is narrowband and requires continuous tuning to keep its sensitivity, the proposed technique is broadband and maintains its performance for any RF signal. On top of that, defining the detection threshold is cumbersome due to the lack of an international standardized criterion. Small responses may appear in the detection system during the test and, sometimes, it is not possible to determine if these are an actual RF breakdown or random noise. This new detection system uses a larger analysis bandwidth, thus reducing the cases in which a small response is difficult to be classified. The proposed detection method represents a major step forward in high power testing as it runs without human intervention, warning the operator or decreasing the RF power automatically much faster than any human operator.