Özlem Coşkun
Özlem Coşkun has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Alihan Kumtepe
Kalyon PV, Turkey
2 shared publications - Mehmet Sankir
Micro and Nanotechnology Graduate Program, TOBB University of Economics and Technology, Ankara, Turkey
2 shared publications - Meriç Çalişkan Arslan
Kalyon PV, Başkent OSB Sadi Türk Bulvarı 23 Malıköy
2 shared publications - Çağrı Taha Delikanlı
Kalyon PV
2 shared publications Alaa Osman
Institute for Solar Energy Research Hamelin (ISFH)
1 shared publication- Ali Bozbey
TOBB Economical and Technological University
1 shared publication
Latest Publications
- Open Access
- 10 September 2026
- Published by TIB Open Publishing in SiliconPV Conference Proceedings
- Vol. 4
Study of Light-Induced Changes in the Optoelectronic Quality of Ga-Doped Silicon Wafers
Light-induced degradation (LID) of boron-doped (B-doped) Czochralski silicon (Cz-Si) due to the formation of boron-oxygen (B-O) defects is a very well-known phenomenon that limits the stability of solar cells. To overcome the detrimental effects of B-O defects, the silicon industry has adopted gallium-doped wafers. However, it has been reported that Ga-doped Cz-Si-based solar cells are affected by light and elevated temperature induced degradation (LeTID), and the origin of this phenomenon at wafer level remains unclear. In this work we investigate light-induced changes in Ga-doped p-type Cz-Si wafers of different resistivities and compare them to the well-known degradation response of B-doped substrates. Through controlled illumination–temperature experiments and photoconductance-based carrier lifetime measurements, we analyse the evolution of minority carrier lifetime and the metastable nature of the lifetime-limiting defects. It was found that upon light-soaking at room temperature for 24 hours, Ga-doped wafers exhibit an average increment in the carrier lifetime, but a drop is observed under dark annealing at 200 ºC for 10 min. This behavior, which has an opposite dynamic to the traditional B-O activation/deactivation process in B-doped wafers, might suggest the existence of a metastable defect in Ga-doped samples. By applying a higher temperature during the light-soaking step, the average carrier lifetime values of Ga-doped samples decrease around 30%, and no recovery is observed under dark annealing conditions at 70 or 200 ºC. Moreover, our results of cyclability suggest that the defects dynamic in Ga-doped Cz-Si is not reversible. The results provide new insights into the mechanisms governing stability in Ga-doped silicon at bare wafer level and their implications for reliable, high-efficiency solar cell manufacturing.
- 10 September 2026
- Published by TIB Open Publishing in SiliconPV Conference Proceedings
- Vol. 4
Open AccessStudy of Light-Induced Changes in the Optoelectronic Quality of Ga-Doped Silicon Wafers
Light-induced degradation (LID) of boron-doped (B-doped) Czochralski silicon (Cz-Si) due to the formation of boron-oxygen (B-O) defects is a very well-known phenomenon that limits the stability of solar cells. To overcome the detrimental effects of B-O defects, the silicon industry has adopted gallium-doped wafers. However, it has been reported that Ga-doped Cz-Si-based solar cells are affected by light and elevated temperature induced degradation (LeTID), and the origin of this phenomenon at wafer level remains unclear. In this work we investigate light-induced changes in Ga-doped p-type Cz-Si wafers of different resistivities and compare them to the well-known degradation response of B-doped substrates. Through controlled illumination–temperature experiments and photoconductance-based carrier lifetime measurements, we analyse the evolution of minority carrier lifetime and the metastable nature of the lifetime-limiting defects. It was found that upon light-soaking at room temperature for 24 hours, Ga-doped wafers exhibit an average increment in the carrier lifetime, but a drop is observed under dark annealing at 200 ºC for 10 min. This behavior, which has an opposite dynamic to the traditional B-O activation/deactivation process in B-doped wafers, might suggest the existence of a metastable defect in Ga-doped samples. By applying a higher temperature during the light-soaking step, the average carrier lifetime values of Ga-doped samples decrease around 30%, and no recovery is observed under dark annealing conditions at 70 or 200 ºC. Moreover, our results of cyclability suggest that the defects dynamic in Ga-doped Cz-Si is not reversible. The results provide new insights into the mechanisms governing stability in Ga-doped silicon at bare wafer level and their implications for reliable, high-efficiency solar cell manufacturing.
- 8 July 2026
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 306
Stability of Ga-doped Cz-Si solar cells under PV-module field conditions
- 8 July 2026
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 306
Stability of Ga-doped Cz-Si solar cells under PV-module field conditions
- Open Access
- 27 November 2025
- Published by EDP Sciences in EPJ Photovoltaics
- Vol. 16, 30
Industrial implementation of 24%-efficient POLO IBC solar cells and future upgrade to 26%-efficient POLO 2 IBC
IBC solar cells have gained tremendous interest in the PV industry as next-generation technology. ISFH has developed a lean manufacturing process sequence for POLO IBC solar cells applying p-type Cz wafers, an Al-BSF base contact and local PECVD deposition of the SiO x N y /n-type polysilicon emitter through a glass shadow mask. In this paper, we report a new best POLO IBC cell efficiency of 24.5% processed at ISFH on M2 wafer size. In 2024, we started to transfer the POLO IBC process from the ISFH SolarTeC to the Kalyon PV manufacturing line using their M10 sized p-type Ga-doped Cz wafers and cell production tools. With Kalyon PV's wet chemistry and PECVD AlO x /SiN tools good surface passivation is demonstrated by obtaining an iV oc up to 727 mV using textured, rear side polished AlO x /SiN passivated test wafers. Kalyon PV targets to process first M10-sized POLO IBC solar cells till end of 2025. However, the POLO IBC efficiency will be limited to below 25.5% by the carrier recombination at the Al-BSF base contact. To overcome this limitation aiming at n-type poly / p-type polysilicon POLO 2 IBC cell efficiencies beyond 26%, EnPV and ISFH optimized a carrier selective SiO x /p-type polysilicon layer stack yielding a new best median saturation current density J 0 = 4 ± 1 fA/cm 2 using industrial tools for the wet chemically grown SiO x and the in-situ doped p-type polysilicon layer. ISFH is applying the SiO x /p-type polysilicon layer stack to develop a novel industrial processing sequence for the POLO 2 IBC solar cell. We deposit both polysilicon layers in-situ-doped full-area and laser-structure both polysilicon polarities. Using lab-type tools and p-type float zone (FZ) wafers, a small-area POLO 2 IBC solar cell with 25.5% efficiency has been developed at ISFH. Using M2-sized n-type Cz wafers, a novel IBC trench patterning process, and solely industrial processing tools in the ISFH SolarTeC targeting very cost-effective processes for etch barrier formation, laser structuring, and polysilicon etching, we obtain a measured implied V oc = 735 mV of POLO 2 IBC cells processed without metal contacts. Since the polysilicon contacts minimize carrier recombination at metal contacts, the implied V oc value demonstrates the high V oc potential of this promising new POLO 2 IBC manufacturing process thereby indicating a conversion efficiency potential above 26%.
- 27 November 2025
- Published by EDP Sciences in EPJ Photovoltaics
- Vol. 16, 30
Open AccessIndustrial implementation of 24%-efficient POLO IBC solar cells and future upgrade to 26%-efficient POLO 2 IBC
IBC solar cells have gained tremendous interest in the PV industry as next-generation technology. ISFH has developed a lean manufacturing process sequence for POLO IBC solar cells applying p-type Cz wafers, an Al-BSF base contact and local PECVD deposition of the SiO x N y /n-type polysilicon emitter through a glass shadow mask. In this paper, we report a new best POLO IBC cell efficiency of 24.5% processed at ISFH on M2 wafer size. In 2024, we started to transfer the POLO IBC process from the ISFH SolarTeC to the Kalyon PV manufacturing line using their M10 sized p-type Ga-doped Cz wafers and cell production tools. With Kalyon PV's wet chemistry and PECVD AlO x /SiN tools good surface passivation is demonstrated by obtaining an iV oc up to 727 mV using textured, rear side polished AlO x /SiN passivated test wafers. Kalyon PV targets to process first M10-sized POLO IBC solar cells till end of 2025. However, the POLO IBC efficiency will be limited to below 25.5% by the carrier recombination at the Al-BSF base contact. To overcome this limitation aiming at n-type poly / p-type polysilicon POLO 2 IBC cell efficiencies beyond 26%, EnPV and ISFH optimized a carrier selective SiO x /p-type polysilicon layer stack yielding a new best median saturation current density J 0 = 4 ± 1 fA/cm 2 using industrial tools for the wet chemically grown SiO x and the in-situ doped p-type polysilicon layer. ISFH is applying the SiO x /p-type polysilicon layer stack to develop a novel industrial processing sequence for the POLO 2 IBC solar cell. We deposit both polysilicon layers in-situ-doped full-area and laser-structure both polysilicon polarities. Using lab-type tools and p-type float zone (FZ) wafers, a small-area POLO 2 IBC solar cell with 25.5% efficiency has been developed at ISFH. Using M2-sized n-type Cz wafers, a novel IBC trench patterning process, and solely industrial processing tools in the ISFH SolarTeC targeting very cost-effective processes for etch barrier formation, laser structuring, and polysilicon etching, we obtain a measured implied V oc = 735 mV of POLO 2 IBC cells processed without metal contacts. Since the polysilicon contacts minimize carrier recombination at metal contacts, the implied V oc value demonstrates the high V oc potential of this promising new POLO 2 IBC manufacturing process thereby indicating a conversion efficiency potential above 26%.
- 8 December 2021
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 5 (12) , 125403
Efficiency enhancement in photoelectrochemical water splitting: Defect passivation and boosted charge transfer kinetics of zinc oxide nanostructures via chalcopyrite/chalcogenide mix sensitization
ZnO thin films in nanorod (NR) and nanoflower (NF) morphologies were used as photoelectrode scaffolds for efficient visible-light-driven photoelectrochemical (PEC) water splitting process, where their decoration with copper indium gallium sulfide (CIGS) and indium sulfide () layers resulted in significant PEC performance enhancement. ZnO NF/CIGS/ photoelectrodes exhibited a remarkably high PEC efficiency ( applied bias photon-to-current efficiency, 83% incident photon-to-current efficiency) due to the negligible dark current, while ZnO NR/CIGS/ generated a photocurrent density of at 0.4 V (vs Ag/AgCl), being one of the highest performances reported in the literature for copper-based chalcopyrite photoelectrodes so far. The interfacial photoelectrode-electrolyte charge transport dynamics, investigated via intensity-modulated photocurrent spectroscopy, exhibited a sevenfold increase in charge transfer efficiencies with a significant drop in surface recombination kinetics for ZnO NF after CIGS/ decoration. The obtained results show consistency with numerically modeled electric field distribution profiles and electron paramagnetic resonance results of ZnO NF, rationalizing the enhanced charge transfer rates for decorated samples and confirming the defect passivating nature of CIGS/.- 8 December 2021
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 5 (12) , 125403
Efficiency enhancement in photoelectrochemical water splitting: Defect passivation and boosted charge transfer kinetics of zinc oxide nanostructures via chalcopyrite/chalcogenide mix sensitization
ZnO thin films in nanorod (NR) and nanoflower (NF) morphologies were used as photoelectrode scaffolds for efficient visible-light-driven photoelectrochemical (PEC) water splitting process, where their decoration with copper indium gallium sulfide (CIGS) and indium sulfide () layers resulted in significant PEC performance enhancement. ZnO NF/CIGS/ photoelectrodes exhibited a remarkably high PEC efficiency ( applied bias photon-to-current efficiency, 83% incident photon-to-current efficiency) due to the negligible dark current, while ZnO NR/CIGS/ generated a photocurrent density of at 0.4 V (vs Ag/AgCl), being one of the highest performances reported in the literature for copper-based chalcopyrite photoelectrodes so far. The interfacial photoelectrode-electrolyte charge transport dynamics, investigated via intensity-modulated photocurrent spectroscopy, exhibited a sevenfold increase in charge transfer efficiencies with a significant drop in surface recombination kinetics for ZnO NF after CIGS/ decoration. The obtained results show consistency with numerically modeled electric field distribution profiles and electron paramagnetic resonance results of ZnO NF, rationalizing the enhanced charge transfer rates for decorated samples and confirming the defect passivating nature of CIGS/.