LSLea Stoilov

Lea Stoilov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Lea Stoilov has a total of 9 co-authors. Here are the top co-authors by number of shared publications:

  • Dominik Kraus

    Department of Prosthodontics, Preclinical Education and Material Sciences, University Hospital, Faculty of Medicine, University of Bonn, Welschnonnenstr. 17, 53111 Bonn, Germany

    2 shared publications
  • Milan Stoilov

    Department of Prosthodontics, Preclinical Education and Dental Materials Science, University of Bonn, 53111 Bonn, Germany

    2 shared publications
  • Helmut Stark

    Department of Prosthodontics, Preclinical Education and Dental Materials Science, University Hospital Bonn, 53111 Bonn, Germany

    1 shared publication
  • Helmut Stark

    Department of Prosthodontics, Preclinical Education and Dental Materials Science, University of Bonn, 53111 Bonn, Germany

    1 shared publication
  • Jochen Winter

    Oral Cell Biology Group, Department of Periodontology, Operative and Preventive Dentistry, University Hospital, Medical Faculty, University of Bonn, Welschnonnenstr. 17, 53111 Bonn, Germany

    1 shared publication
  • Markus Klemmer

    Department of Prosthodontics, Preclinical Education and Dental Materials Science, University Hospital Bonn, 53111 Bonn, Germany

    1 shared publication

Latest Publications

  • Open Access

    Effects of Different Titanium Surface Treatments on Adhesion, Proliferation and Differentiation of Bone Cells: An In Vitro Study

    by Milan Stoilov, Lea Stoilov, Norbert Enkling, Helmut Stark, Jochen Winter, Michael Marder, Dominik Kraus

    The objective of this study was to evaluate the impacts of different sandblasting procedures in acid etching of Ti6Al4V surfaces on osteoblast cell behavior, regarding various physicochemical and topographical parameters. Furthermore, differences in osteoblast cell behavior between cpTi and Ti6Al4V SA surfaces were evaluated. Sandblasting and subsequent acid etching of cpTi and Ti6Al4V discs was performed with Al2O3 grains of different sizes and with varying blasting pressures. The micro- and nano-roughness of the experimental SA surfaces were analyzed via confocal, atomic force and scanning electron microscopy. Surface free energy and friction coefficients were determined. hFOB 1.19 cells were seeded to evaluate adhesion, proliferation and osteoblastic differentiation for up to 12 d via crystal violet assays, MTT assays, ALP activity assays and Alizarin Red staining assays. Differences in blasting procedures had significant impacts on surface macro- and micro-topography. The crystal violet assay revealed a significant inverse relationship between blasting grain size and hFOB cell growth after 7 days. This trend was also visible in the Alizarin Red assays staining after 12 d: there was significantly higher biomineralization visible in the group that was sandblasted with smaller grains (F180) when compared to standard-grain-size groups (F70). SA samples treated with reduced blasting pressure exhibited lower hFOB adhesion and growth capabilities at initial (2 h) and later time points for up to 7 days, when compared to the standard SA surface, even though micro-roughness and other relevant surface parameters were similar. Overall, etched-only surfaces consistently exhibited equivalent or higher adhesion, proliferation and differentiation capabilities when compared to all other sandblasted and etched surfaces. No differences were found between cpTi and Ti6Al4V SA surfaces. Subtle modifications in the blasting protocol for Ti6Al4V SA surfaces significantly affect the proliferative and differentiation behavior of human osteoblasts. Surface roughness parameters are not sufficient to predict osteoblast behavior on etched Ti6Al4V surfaces.


  • Open Access

    Comparison of Digital Self-Assessment Systems and Faculty Feedback for Tooth Preparation in a Preclinical Simulation

    by Milan Stoilov, Lea Trebess, Markus Klemmer, Helmut Stark, Norbert Enkling, Dominik Kraus

    Background: Regarding the new dental licensing regulations in Germany (AOZ), this study evaluated the effectiveness of two different digital tooth preparation validation systems in comparison to traditional faculty feedback. Methods: Participants were randomly divided into groups: Faculty Feedback (FF: n = 33), PrepCheck® (PC: n = 32) and Dental Teacher™ (n = 32). Students had the task to prepare tooth 16 for a retentive full-cast crown. Preparations could be repeated as often as desired. Feedback was provided either by faculty staff or by digital validation systems only. Exams were conducted and graded by two independent and experienced examiners. A survey was performed to evaluate the assessment concepts. Results: No statistical difference in examination performance between groups could be observed. Nevertheless, the survey showed participants preferred consulting the faculty staff rather than the digital validation systems. Students preferred practising with DT rather than with PC. Conclusions: Although both classical and digital methods showed comparable results regarding the preparation examination performance, direct feedback by the faculty staff is still appreciated by the students. A combination of both methods is mandatory since demonstration and advice by the teacher is needed. However, digital tooth preparation validation systems are predestined for free practice sessions, providing self-assessment.