Burak Uzal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Burak Uzal has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Cengiz Duran Atiş
Department of Civil Engineering, Erciyes University, Kayseri 38039, Turkey
2 shared publications - Hediye Yorulmaz
Civil Engineering Department, Abdullah Gül University, Kayseri, Turkey
2 shared publications - Kimberly E. Kurtis
Georgia Institute of Technology
2 shared publications Okan Karahan
2 shared publications- Angus P. Wilkinson
School of Chemistry and Biochemistry, Georgia Institute of Technology, Atlanta, Georgia 30332-0400, United States
1 shared publication - Bo Rider
School of Civil and Environmental Engineering Georgia Institute of Technology Atlanta Georgia USA gatech.edu
1 shared publication
Latest Publications
- 26 May 2026
- Published by Emerald Publishing in Advances in Cement Research
- Vol. 38 (10) , 649-661
Effects of alkanolamines on calcium sulfoaluminate belite cement hydration and fresh properties
Calcium sulfoaluminate belite cements have found widespread use in specialised applications but have not been applied broadly due to rapid setting times. Conventional set retarders such as citric and tartaric acids modify hydration kinetics, introducing ancillary effects that alkanolamines may avoid. This study examined the effects of three alkanolamines, triisopropanolamine (TIPA), triethanolamine (TEA) and diisopropanolamine (DIPA), on early hydration at 0.02% dosage; TIPA was also tested across a broader dosage range. Reaction kinetics and phase evolution were examined in pastes by calorimetry, thermogravimetric analysis (TGA) and in situ quantitative X-ray diffraction (QXRD) for 72 h of hydration, along with setting time and amplitude-sweep rheometry. Calorimetry showed that TEA and DIPA delayed and reduced the main cement hydration peak, while all alkanolamines delayed and enhanced the shoulder and secondary hydration peaks. In situ QXRD and TGA suggested that alkanolamines decrease ettringite and alumina gel formation by 24 h and may lead to poorly crystallised ettringite that cannot be quantified by QXRD. Alkanolamine-containing samples demonstrated increased storage and loss moduli and extended linear viscoelastic ranges. A consistent grouping of similar behaviour emerged: control/TIPA versus TEA/DIPA, suggesting distinct mechanisms. Finally, among the alkanolamines, TEA was the most effective, increasing the setting time by 18 min.
- 26 May 2026
- Published by Emerald Publishing in Advances in Cement Research
- Vol. 38 (10) , 649-661
Effects of alkanolamines on calcium sulfoaluminate belite cement hydration and fresh properties
Calcium sulfoaluminate belite cements have found widespread use in specialised applications but have not been applied broadly due to rapid setting times. Conventional set retarders such as citric and tartaric acids modify hydration kinetics, introducing ancillary effects that alkanolamines may avoid. This study examined the effects of three alkanolamines, triisopropanolamine (TIPA), triethanolamine (TEA) and diisopropanolamine (DIPA), on early hydration at 0.02% dosage; TIPA was also tested across a broader dosage range. Reaction kinetics and phase evolution were examined in pastes by calorimetry, thermogravimetric analysis (TGA) and in situ quantitative X-ray diffraction (QXRD) for 72 h of hydration, along with setting time and amplitude-sweep rheometry. Calorimetry showed that TEA and DIPA delayed and reduced the main cement hydration peak, while all alkanolamines delayed and enhanced the shoulder and secondary hydration peaks. In situ QXRD and TGA suggested that alkanolamines decrease ettringite and alumina gel formation by 24 h and may lead to poorly crystallised ettringite that cannot be quantified by QXRD. Alkanolamine-containing samples demonstrated increased storage and loss moduli and extended linear viscoelastic ranges. A consistent grouping of similar behaviour emerged: control/TIPA versus TEA/DIPA, suggesting distinct mechanisms. Finally, among the alkanolamines, TEA was the most effective, increasing the setting time by 18 min.
- Open Access
- 1 January 2026
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2026 (1)
Evaluation of Machine‐Learned Oscillatory Rheology to Design Blended Cement Systems for 3D Printing
For successful construction, three‐dimensional concrete printing (3DCP) demands tailored fresh‐state properties balancing pumpability, extrudability, and buildability. In this work, machine learning was applied to predict testability and printability of Portland‐limestone cement–metakaolin (PLC‐MK) mixtures; testability was defined as the ability to form a homogeneous mixture, while printability represented the quality of the 3DCP forms. It was hypothesized that printability could be related to storage modulus, viscosity, flow onset stress, and open time, and a dataset of 54 PLC‐MK mixtures with a water–binder ratio of 0.30–0.45, metakaolin fraction up to 30% by weight, and polycarboxylate superplasticizer dosage up to 0.4% by weight of binder was generated to explore the dependence of composition on rheology. From such data, a hierarchical machine learning framework incorporating physicochemical domain knowledge was developed to classify testability and identify mixtures with rheological parameters associated with printability. Such mixtures had a water–binder ratio of 0.30–0.34 with either high metakaolin and superplasticizer content (21%–30% and 0.35%–0.37%, respectively) or low metakaolin and superplasticizer content (6%–12% and 0.17%–0.18%, respectively). To test the transferability of paste‐scale rheological descriptors to mortar‐scale printing behavior, two candidate mixtures were selected for validation. A low metakaolin–low superplasticizer mortar exhibited filament tearing during printing, while a high metakaolin–high superplasticizer mortar was difficult to extrude and displayed behavior consistent with apparent shear thickening. Although the hierarchical machine learning framework successfully predicted the targeted oscillatory rheological properties, the validation experiments revealed important limitations in translating those paste‐scale descriptors directly to mortar‐scale printing performance. The results indicate that oscillatory rheology, while informative for mixture characterization, does not fully capture the extrusion‐related phenomena governing printability. Nevertheless, hierarchical machine learning successfully modeled the composition–property relationships in PLC‐MK blends and provides a framework for future mixture design as characterization methods for extrusion and printing continue to develop.
- 1 January 2026
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2026 (1)
Open AccessEvaluation of Machine‐Learned Oscillatory Rheology to Design Blended Cement Systems for 3D Printing
For successful construction, three‐dimensional concrete printing (3DCP) demands tailored fresh‐state properties balancing pumpability, extrudability, and buildability. In this work, machine learning was applied to predict testability and printability of Portland‐limestone cement–metakaolin (PLC‐MK) mixtures; testability was defined as the ability to form a homogeneous mixture, while printability represented the quality of the 3DCP forms. It was hypothesized that printability could be related to storage modulus, viscosity, flow onset stress, and open time, and a dataset of 54 PLC‐MK mixtures with a water–binder ratio of 0.30–0.45, metakaolin fraction up to 30% by weight, and polycarboxylate superplasticizer dosage up to 0.4% by weight of binder was generated to explore the dependence of composition on rheology. From such data, a hierarchical machine learning framework incorporating physicochemical domain knowledge was developed to classify testability and identify mixtures with rheological parameters associated with printability. Such mixtures had a water–binder ratio of 0.30–0.34 with either high metakaolin and superplasticizer content (21%–30% and 0.35%–0.37%, respectively) or low metakaolin and superplasticizer content (6%–12% and 0.17%–0.18%, respectively). To test the transferability of paste‐scale rheological descriptors to mortar‐scale printing behavior, two candidate mixtures were selected for validation. A low metakaolin–low superplasticizer mortar exhibited filament tearing during printing, while a high metakaolin–high superplasticizer mortar was difficult to extrude and displayed behavior consistent with apparent shear thickening. Although the hierarchical machine learning framework successfully predicted the targeted oscillatory rheological properties, the validation experiments revealed important limitations in translating those paste‐scale descriptors directly to mortar‐scale printing performance. The results indicate that oscillatory rheology, while informative for mixture characterization, does not fully capture the extrusion‐related phenomena governing printability. Nevertheless, hierarchical machine learning successfully modeled the composition–property relationships in PLC‐MK blends and provides a framework for future mixture design as characterization methods for extrusion and printing continue to develop.
- 20 November 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 409
Reaction kinetics and properties of pumice-based geopolymer systems cured at room temperature
- 20 November 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 409
Reaction kinetics and properties of pumice-based geopolymer systems cured at room temperature
- 16 December 2021
- Published by Tulpar Academic Publishing in Challenge Journal of Concrete Research Letters
- Vol. 12 (4) , 125
Effects of dry particle coating with nano- and microparticles on early compressive strength of portland cement pastes
It is known that nano-and microparticles have been very popular in recent years since their advantages. However, due to the very small size of such materials, they have very high tendency to agglomeration particularly for nanoparticles. Therefore, it is critical that they are properly distributed in the system to which they are added. This paper investigated the effects of dry particle coating with nano-and microparticles to solve the agglomeration problem. For a clear evaluation, paste samples were preferred to detemine the compressive strength. Nano-SiO2 and nano-CaCO3, micro-CaCO3 and micro-SiO2, also known as silica fume, were selected as particulate additives. It was studied by the addition of various percentages (0.3, 0.7, 1, 2, 3 and 5%) of nano-and microparticles in cementitious systems, replacing cement by weight with and without dry particle coating. Dry particle coating was made by using a high-speed paddle mixer. Portland cement and additive particles were mixed at 1500 rpm for 30 seconds in high-speed powder mixer designed for this purpose. The 3-day compressive strength of the cement-based samples to which particles were added at the specified rates was determined and the effect of the dry particle coating on the early strength was investigated. According to the results, it was observed that the production of paste with the dry particle coating technique gave higher compressive strength compared to the production of paste directly in early period. Especially with dry particle coating, compressive strength increased more than 100% in paste samples containing 0.3% nano-SiO2 compared to direct addition without coating.
- 16 December 2021
- Published by Tulpar Academic Publishing in Challenge Journal of Concrete Research Letters
- Vol. 12 (4) , 125
Effects of dry particle coating with nano- and microparticles on early compressive strength of portland cement pastes
It is known that nano-and microparticles have been very popular in recent years since their advantages. However, due to the very small size of such materials, they have very high tendency to agglomeration particularly for nanoparticles. Therefore, it is critical that they are properly distributed in the system to which they are added. This paper investigated the effects of dry particle coating with nano-and microparticles to solve the agglomeration problem. For a clear evaluation, paste samples were preferred to detemine the compressive strength. Nano-SiO2 and nano-CaCO3, micro-CaCO3 and micro-SiO2, also known as silica fume, were selected as particulate additives. It was studied by the addition of various percentages (0.3, 0.7, 1, 2, 3 and 5%) of nano-and microparticles in cementitious systems, replacing cement by weight with and without dry particle coating. Dry particle coating was made by using a high-speed paddle mixer. Portland cement and additive particles were mixed at 1500 rpm for 30 seconds in high-speed powder mixer designed for this purpose. The 3-day compressive strength of the cement-based samples to which particles were added at the specified rates was determined and the effect of the dry particle coating on the early strength was investigated. According to the results, it was observed that the production of paste with the dry particle coating technique gave higher compressive strength compared to the production of paste directly in early period. Especially with dry particle coating, compressive strength increased more than 100% in paste samples containing 0.3% nano-SiO2 compared to direct addition without coating.
- 1 November 2011
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 63 (11) , 837-846
Some characteristics of fibre-reinforced semi-lightweight concrete with unexpanded perlite
Lightweight aggregate concrete is not a new invention of modern concrete technology, but dates back even to before the Christian era. Natural aggregates like scoria or pumice were utilised in masterpieces such as Babylon of the Sumerians, Hagia Sophia in Istanbul or the Pantheon of the Romans. The demand for lightweight aggregate concrete increased over time because of its advantages, specifically properties such as its thermal insulating properties and low density. It has also become an important structural material in off-shore construction during recent years. A comprehensive study was carried out in METU Mechanics of Materials Laboratory in order to investigate some characteristics of fibre-reinforced semi-lightweight concrete for seismic strengthening purposes of reinforced concrete framed structures. Semi-lightweight concrete containing unexpanded perlite, both as lightweight aggregate and as a supplementary cementing material, was reinforced by polypropylene and steel fibres, separately. Compressive strength, split tensile strength and modulus of elasticity measurements were carried out on cylinder specimens. Steel-mesh-reinforced semi-lightweight concrete plates were also tested as reference specimens for the toughness test and the results were compared with those for fibre-reinforced semi-lightweight concrete plates. Cylinder test results indicated a considerable increase in 28-day compressive strength in the case of unexpanded perlite powder replacement; while providing lower tensile strength and modulus of elasticity. Toughness test results indicated the superiority of polypropylene fibre-reinforced semi-lightweight concrete for seismic strengthening purposes in the case of fibre utilisation.
- 1 November 2011
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 63 (11) , 837-846
Some characteristics of fibre-reinforced semi-lightweight concrete with unexpanded perlite
Lightweight aggregate concrete is not a new invention of modern concrete technology, but dates back even to before the Christian era. Natural aggregates like scoria or pumice were utilised in masterpieces such as Babylon of the Sumerians, Hagia Sophia in Istanbul or the Pantheon of the Romans. The demand for lightweight aggregate concrete increased over time because of its advantages, specifically properties such as its thermal insulating properties and low density. It has also become an important structural material in off-shore construction during recent years. A comprehensive study was carried out in METU Mechanics of Materials Laboratory in order to investigate some characteristics of fibre-reinforced semi-lightweight concrete for seismic strengthening purposes of reinforced concrete framed structures. Semi-lightweight concrete containing unexpanded perlite, both as lightweight aggregate and as a supplementary cementing material, was reinforced by polypropylene and steel fibres, separately. Compressive strength, split tensile strength and modulus of elasticity measurements were carried out on cylinder specimens. Steel-mesh-reinforced semi-lightweight concrete plates were also tested as reference specimens for the toughness test and the results were compared with those for fibre-reinforced semi-lightweight concrete plates. Cylinder test results indicated a considerable increase in 28-day compressive strength in the case of unexpanded perlite powder replacement; while providing lower tensile strength and modulus of elasticity. Toughness test results indicated the superiority of polypropylene fibre-reinforced semi-lightweight concrete for seismic strengthening purposes in the case of fibre utilisation.