Xuanjin Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Xuanjin Sun has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Desheng Rong
Faculty of Electrical and Control Engineering, Liaoning Technical University, Huludao, China
12 shared publications - Chao Li
Faculty of Electrical and Control Engineering, Liaoning Technical University, Huludao, China
7 shared publications - Hongzhu Li
Faculty of Electrical and Control Engineering of Liaoning Technical University, Huludao, China
5 shared publications - Yadong Han
Faculty of Electrical and Control Engineering, Liaoning Technical University, Huludao, China
5 shared publications - Zhongbao Lin
Faculty of Electrical and Control Engineering, Liaoning Technical University, Huludao, China
5 shared publications Ning Wang
School of Mechanical Electronic and Information Engineering, China University of Mining and Technology, Beijing, China
4 shared publications
Latest Publications
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 15770-15785
High Step-Up Interleaved Soft-Switching Boost Converter Based on Coupled Inductors
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 15770-15785
High Step-Up Interleaved Soft-Switching Boost Converter Based on Coupled Inductors
- 10 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Novel Current Fed Dual Active Bridge Converter for Photovoltaic On-Board Charger and Its Control Strategy
Photovoltaic (PV) fluctuations can lead to DC link voltage fluctuations and pose challenges for wide load efficiency optimization. This article proposes a Novel Current Fed Dual Active Bridge (NCF-DAB) converter and its corresponding control strategy to address these issues in PV On-Board Charger. NCF-DAB utilizes an interleaved parallel boost and full bridge hybrid structure with an auxiliary inductor. Full range duty cycle control is adopted to maintain continuous operation and suppress DC link voltage fluctuations. Furthermore, full load range Zero Voltage Switching (ZVS) is realized by integrating phase shift control. A detailed analysis of the operating principle of NCF-DAB is given, and key parameter design are presented. To verify the proposed converter, an experimental prototype with 35 - 42 V input, 380-420V output, and 800W was constructed. Experimental results indicate that the peak efficiency of NCF-DAB reached 96.58%.
- 10 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Novel Current Fed Dual Active Bridge Converter for Photovoltaic On-Board Charger and Its Control Strategy
Photovoltaic (PV) fluctuations can lead to DC link voltage fluctuations and pose challenges for wide load efficiency optimization. This article proposes a Novel Current Fed Dual Active Bridge (NCF-DAB) converter and its corresponding control strategy to address these issues in PV On-Board Charger. NCF-DAB utilizes an interleaved parallel boost and full bridge hybrid structure with an auxiliary inductor. Full range duty cycle control is adopted to maintain continuous operation and suppress DC link voltage fluctuations. Furthermore, full load range Zero Voltage Switching (ZVS) is realized by integrating phase shift control. A detailed analysis of the operating principle of NCF-DAB is given, and key parameter design are presented. To verify the proposed converter, an experimental prototype with 35 - 42 V input, 380-420V output, and 800W was constructed. Experimental results indicate that the peak efficiency of NCF-DAB reached 96.58%.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (12) , 1-15
A Low Input Current Ripple Symmetric Bipolar Output Converter for Bipolar DC Distribution Systems
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (12) , 1-15
A Low Input Current Ripple Symmetric Bipolar Output Converter for Bipolar DC Distribution Systems
- Open Access
- 22 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 7, 157-172
OBC and APM Integration Topology and Decoupling Design for Solar Electric Vehicle
Integration of electric vehicle power conversion units presents a promising solution, yet introduces challenges including inter-port power coupling and compromised efficiency in integrated systems. This paper proposes a photovoltaic compatible integrated converter combining on-board charger (OBC) with auxiliary power module (APM), featuring cost effectiveness and high power density. Introduction of decoupling capacitor enables charging decoupling between high voltage battery (HVB) and low voltage battery (LVB), thereby simplifying multi-port energy management. Furthermore, minimum current ratio is employed to determine optimal phase shift, achieving minimized conduction losses during HVB charging while maintaining zero voltage switching (ZVS) for all switches. Comprehensive analysis of proposed converter is conducted, covering operational principles, steady-state performance, soft switching characteristics, efficiency and loss breakdown, along with control methodology. Experimental prototype rated at 500W for OBC and 300W for APM is implemented to validate converter performance. Experimental results demonstrate peak system efficiency of 95.3% during simultaneous HVB and LVB charging, and 93.16% during LVB charging alone, confirming effectiveness of proposed converter.
- 22 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 7, 157-172
Open AccessOBC and APM Integration Topology and Decoupling Design for Solar Electric Vehicle
Integration of electric vehicle power conversion units presents a promising solution, yet introduces challenges including inter-port power coupling and compromised efficiency in integrated systems. This paper proposes a photovoltaic compatible integrated converter combining on-board charger (OBC) with auxiliary power module (APM), featuring cost effectiveness and high power density. Introduction of decoupling capacitor enables charging decoupling between high voltage battery (HVB) and low voltage battery (LVB), thereby simplifying multi-port energy management. Furthermore, minimum current ratio is employed to determine optimal phase shift, achieving minimized conduction losses during HVB charging while maintaining zero voltage switching (ZVS) for all switches. Comprehensive analysis of proposed converter is conducted, covering operational principles, steady-state performance, soft switching characteristics, efficiency and loss breakdown, along with control methodology. Experimental prototype rated at 500W for OBC and 300W for APM is implemented to validate converter performance. Experimental results demonstrate peak system efficiency of 95.3% during simultaneous HVB and LVB charging, and 93.16% during LVB charging alone, confirming effectiveness of proposed converter.
- 25 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (1) , 1970-1980
High Step-Up Dual Coupled-Inductors Interleaved Quadratic DC–DC Converter With Common Ground and Low Input Current Ripple for Fuel Cell Electric Vehicles
In this article, a novel interleaved quadratic dc–dc converter with dual coupled inductors has been proposed for fuel cell electric vehicles (FCEVs). The proposed converter is generated by cascading two boost converters and integrating a coupled-inductor multiplier cell and an output filter. The quadratic voltage gain is achieved and it can be increased by the turns ratio without the need of extreme duty cycle. The output filter capacitor is clamped at the input to achieve an input and output common ground. Furthermore, the two primary windings and the load are connected at the input to share the current, and very low input current ripple is achieved by using interleaved control. Diode-capacitor branch of the topology is multiplexed as the passive clamp branch to effectively reduce the voltage stress of the switches. The currents of the switching devices are limited by the leakage inductance during the mode conversions, which effectively alleviates the hard-switching problem. This article also gives the key performance of the proposed converter and compares it with other high step-up converters. Finally, a 400-W prototype is built to verify the theoretical analysis.
- 25 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (1) , 1970-1980
High Step-Up Dual Coupled-Inductors Interleaved Quadratic DC–DC Converter With Common Ground and Low Input Current Ripple for Fuel Cell Electric Vehicles
In this article, a novel interleaved quadratic dc–dc converter with dual coupled inductors has been proposed for fuel cell electric vehicles (FCEVs). The proposed converter is generated by cascading two boost converters and integrating a coupled-inductor multiplier cell and an output filter. The quadratic voltage gain is achieved and it can be increased by the turns ratio without the need of extreme duty cycle. The output filter capacitor is clamped at the input to achieve an input and output common ground. Furthermore, the two primary windings and the load are connected at the input to share the current, and very low input current ripple is achieved by using interleaved control. Diode-capacitor branch of the topology is multiplexed as the passive clamp branch to effectively reduce the voltage stress of the switches. The currents of the switching devices are limited by the leakage inductance during the mode conversions, which effectively alleviates the hard-switching problem. This article also gives the key performance of the proposed converter and compares it with other high step-up converters. Finally, a 400-W prototype is built to verify the theoretical analysis.
- 23 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (2) , 2355-2366
A High Step-Up Quadratic DC–DC Converter-Based Y-Source Coupled Inductor With Quasi-Resonance Operation
This article proposes a high step-up quadratic dc–dc converter-based Y-source coupled inductor (YSCI) with quasi-resonance operation, which integrates a modified quadratic Boost-Sepic converter, switched capacitor, and YSCI to achieve high voltage gain with reduced voltage stress across semiconductors. The leakage inductor of YSCI limits the current change rate, achieving zero current switching (ZCS) turn-on for the switches and mitigating reverse recovery of diodes. Simultaneously, it facilitates quasi-resonant operation, which contributes to ZCS turn-off for diodes. Moreover, the switched capacitor is integrated with passive clamped circuit to reduce the voltage rating across the output capacitor. Additionally, the leakage energy stored in the leakage inductor is absorbed by the switched capacitor, thereby limiting voltage spikes across the semiconductors. The input inductors of modified quadratic Boost-Sepic converter ensure the continuous input current. The operation principles, steady-state analysis, and design considerations of the proposed converter are detailed. Finally, the theoretical analysis is validated through the construction of a 400 W experimental prototype with input and output voltages of 24 and 400 V, respectively.
- 23 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (2) , 2355-2366
A High Step-Up Quadratic DC–DC Converter-Based Y-Source Coupled Inductor With Quasi-Resonance Operation
This article proposes a high step-up quadratic dc–dc converter-based Y-source coupled inductor (YSCI) with quasi-resonance operation, which integrates a modified quadratic Boost-Sepic converter, switched capacitor, and YSCI to achieve high voltage gain with reduced voltage stress across semiconductors. The leakage inductor of YSCI limits the current change rate, achieving zero current switching (ZCS) turn-on for the switches and mitigating reverse recovery of diodes. Simultaneously, it facilitates quasi-resonant operation, which contributes to ZCS turn-off for diodes. Moreover, the switched capacitor is integrated with passive clamped circuit to reduce the voltage rating across the output capacitor. Additionally, the leakage energy stored in the leakage inductor is absorbed by the switched capacitor, thereby limiting voltage spikes across the semiconductors. The input inductors of modified quadratic Boost-Sepic converter ensure the continuous input current. The operation principles, steady-state analysis, and design considerations of the proposed converter are detailed. Finally, the theoretical analysis is validated through the construction of a 400 W experimental prototype with input and output voltages of 24 and 400 V, respectively.
- 11 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4679-4690
Expandable High Step-Up Soft-Switching Integrated Boost–SEPIC Converter With Y-Source Coupled Inductor
This article proposes a high step-up soft-switching integrated Boost-Sepic converter with a Y-source coupled inductor for interface circuit of renewable energy power generation systems. By combining the Boost converter, Sepic converter, and Y-source coupled inductor, the converter achieves a higher voltage gain. Additionally, it features low input current ripple and a common ground for both the input and output. A series of multiple switched capacitor units can be cascaded on the output side of the converter, allowing for enhanced flexibility and expandability. The output voltage is shared by three capacitors, which effectively reduces the voltage stress on the capacitors and reduces the size of the capacitors. In addition, the active clamping circuit effectively utilizes the leakage inductance energy, enabling zero-voltage switching (ZVS) for the switch and zero-current switching (ZCS) for the diode, thereby reducing the loss of the switching elements. Since the switch is positioned before the Y-source, the switch also has lower voltage stress and operates over the full duty cycle range. This article presents a detailed analysis of the operating principle and steady-state performance of the converter. A 400W experimental prototype was constructed to validate the correctness and feasibility of the theoretical analysis.
- 11 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4679-4690
Expandable High Step-Up Soft-Switching Integrated Boost–SEPIC Converter With Y-Source Coupled Inductor
This article proposes a high step-up soft-switching integrated Boost-Sepic converter with a Y-source coupled inductor for interface circuit of renewable energy power generation systems. By combining the Boost converter, Sepic converter, and Y-source coupled inductor, the converter achieves a higher voltage gain. Additionally, it features low input current ripple and a common ground for both the input and output. A series of multiple switched capacitor units can be cascaded on the output side of the converter, allowing for enhanced flexibility and expandability. The output voltage is shared by three capacitors, which effectively reduces the voltage stress on the capacitors and reduces the size of the capacitors. In addition, the active clamping circuit effectively utilizes the leakage inductance energy, enabling zero-voltage switching (ZVS) for the switch and zero-current switching (ZCS) for the diode, thereby reducing the loss of the switching elements. Since the switch is positioned before the Y-source, the switch also has lower voltage stress and operates over the full duty cycle range. This article presents a detailed analysis of the operating principle and steady-state performance of the converter. A 400W experimental prototype was constructed to validate the correctness and feasibility of the theoretical analysis.
- 17 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (9) , 9160-9171
A High Step-Up Cuk-Boost Converter Based on Coupled Inductor With Continuous Ports Currents and Current Sharing Design
A high step-up Cuk-Boost converter based on coupled inductors for renewable energy systems has been proposed in this article. Higher voltage gains and continuous input and output ports currents are achieved by utilizing topology integration technique and coupled inductor multiplier technique. The low current ripple in the input side is employed by driving the two switches in an interleaved manner. The energy generated by the leakage inductance is absorbed by the passive clamp circuit, which reduces the voltage spike of the switches. The current sharing between the two switches is achieved. In addition, the zero-current switching (ZCS) of the switches is achieved and the reverse recovery problem of the diodes is alleviated. The operation principles and performance of the proposed converter are analyzed in detail at full duty cycle range. Meanwhile, the current equalization design and the design reference of the components are given. Finally, a 400 W, 28–42 V input, 400 V output experimental prototype is built to verify the theoretical analysis.
- 17 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (9) , 9160-9171
A High Step-Up Cuk-Boost Converter Based on Coupled Inductor With Continuous Ports Currents and Current Sharing Design
A high step-up Cuk-Boost converter based on coupled inductors for renewable energy systems has been proposed in this article. Higher voltage gains and continuous input and output ports currents are achieved by utilizing topology integration technique and coupled inductor multiplier technique. The low current ripple in the input side is employed by driving the two switches in an interleaved manner. The energy generated by the leakage inductance is absorbed by the passive clamp circuit, which reduces the voltage spike of the switches. The current sharing between the two switches is achieved. In addition, the zero-current switching (ZCS) of the switches is achieved and the reverse recovery problem of the diodes is alleviated. The operation principles and performance of the proposed converter are analyzed in detail at full duty cycle range. Meanwhile, the current equalization design and the design reference of the components are given. Finally, a 400 W, 28–42 V input, 400 V output experimental prototype is built to verify the theoretical analysis.
- 10 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (3) , 7463-7474
A Novel Nonisolated Dual-Input High Step-Up DC-DC Converter With Three-Winding Coupled Inductor for Electric Vehicle Charging Station
Dual-input DC-DC converters are increasingly recognized as integrated systems for various applications, such as electric vehicle charging station and distributed energy systems, due to the compact size and cost-effectiveness. Therefore, a novel dual-input single-output high step-up DC-DC converter with three-winding coupled inductor (DISO-TWCI), which secondary and tertiary windings are integrated with switched capacitor, is proposed to achieve a high voltage conversion ratio without an extremely duty cycle. And the diode-capacitor clamp circuit is utilized to minimize the voltage spikes across switches, which is beneficial for selecting switches with low voltage ratings. Moreover, the switches can achieve the Zero Current Switching (ZCS) with the help of leakage inductor from TWCI. By integrating the passive clamp network, the number of components in DISO-TWCI can be reduced, significantly enhancing its performance. The operating principles, steady-state analysis, design and performance analysis of DISO-TWCI are described in detail. Finally, the theoretical correctness is verified by building an experimental prototype with switching frequency of 100 kHz. The rated power is 400 W with 24-24V input and 400V output.
- 10 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (3) , 7463-7474
A Novel Nonisolated Dual-Input High Step-Up DC-DC Converter With Three-Winding Coupled Inductor for Electric Vehicle Charging Station
Dual-input DC-DC converters are increasingly recognized as integrated systems for various applications, such as electric vehicle charging station and distributed energy systems, due to the compact size and cost-effectiveness. Therefore, a novel dual-input single-output high step-up DC-DC converter with three-winding coupled inductor (DISO-TWCI), which secondary and tertiary windings are integrated with switched capacitor, is proposed to achieve a high voltage conversion ratio without an extremely duty cycle. And the diode-capacitor clamp circuit is utilized to minimize the voltage spikes across switches, which is beneficial for selecting switches with low voltage ratings. Moreover, the switches can achieve the Zero Current Switching (ZCS) with the help of leakage inductor from TWCI. By integrating the passive clamp network, the number of components in DISO-TWCI can be reduced, significantly enhancing its performance. The operating principles, steady-state analysis, design and performance analysis of DISO-TWCI are described in detail. Finally, the theoretical correctness is verified by building an experimental prototype with switching frequency of 100 kHz. The rated power is 400 W with 24-24V input and 400V output.