Yadong Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Yadong Han has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Desheng Rong
Faculty of Electrical and Control Engineering, Liaoning Technical University, Huludao, China
5 shared publications - Xuanjin Sun
Faculty of Electrical and Control Engineering, Liaoning Technical University, Huludao, China
5 shared publications - Zhongbao Lin
Faculty of Electrical and Control Engineering, Liaoning Technical University, Huludao, China
4 shared publications - Changxuan Li
Faculty of Electrical and Control Engineering, Liaoning Technical University, China
3 shared publications Changxuan Li
Faculty of Electrical and Control Engineering, Liaoning Technical University, Fuxin, China
2 shared publications- Dengxun Ma
Faculty of Electrical and Control Engineering, Liaoning Technical University, Huludao, China
1 shared publication
Latest Publications
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 15770-15785
High Step-Up Interleaved Soft-Switching Boost Converter Based on Coupled Inductors
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 15770-15785
High Step-Up Interleaved Soft-Switching Boost Converter Based on Coupled Inductors
- 10 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Novel Current Fed Dual Active Bridge Converter for Photovoltaic On-Board Charger and Its Control Strategy
Photovoltaic (PV) fluctuations can lead to DC link voltage fluctuations and pose challenges for wide load efficiency optimization. This article proposes a Novel Current Fed Dual Active Bridge (NCF-DAB) converter and its corresponding control strategy to address these issues in PV On-Board Charger. NCF-DAB utilizes an interleaved parallel boost and full bridge hybrid structure with an auxiliary inductor. Full range duty cycle control is adopted to maintain continuous operation and suppress DC link voltage fluctuations. Furthermore, full load range Zero Voltage Switching (ZVS) is realized by integrating phase shift control. A detailed analysis of the operating principle of NCF-DAB is given, and key parameter design are presented. To verify the proposed converter, an experimental prototype with 35 - 42 V input, 380-420V output, and 800W was constructed. Experimental results indicate that the peak efficiency of NCF-DAB reached 96.58%.
- 10 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Novel Current Fed Dual Active Bridge Converter for Photovoltaic On-Board Charger and Its Control Strategy
Photovoltaic (PV) fluctuations can lead to DC link voltage fluctuations and pose challenges for wide load efficiency optimization. This article proposes a Novel Current Fed Dual Active Bridge (NCF-DAB) converter and its corresponding control strategy to address these issues in PV On-Board Charger. NCF-DAB utilizes an interleaved parallel boost and full bridge hybrid structure with an auxiliary inductor. Full range duty cycle control is adopted to maintain continuous operation and suppress DC link voltage fluctuations. Furthermore, full load range Zero Voltage Switching (ZVS) is realized by integrating phase shift control. A detailed analysis of the operating principle of NCF-DAB is given, and key parameter design are presented. To verify the proposed converter, an experimental prototype with 35 - 42 V input, 380-420V output, and 800W was constructed. Experimental results indicate that the peak efficiency of NCF-DAB reached 96.58%.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (12) , 1-15
A Low Input Current Ripple Symmetric Bipolar Output Converter for Bipolar DC Distribution Systems
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (12) , 1-15
A Low Input Current Ripple Symmetric Bipolar Output Converter for Bipolar DC Distribution Systems
- Open Access
- 22 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 7, 157-172
OBC and APM Integration Topology and Decoupling Design for Solar Electric Vehicle
Integration of electric vehicle power conversion units presents a promising solution, yet introduces challenges including inter-port power coupling and compromised efficiency in integrated systems. This paper proposes a photovoltaic compatible integrated converter combining on-board charger (OBC) with auxiliary power module (APM), featuring cost effectiveness and high power density. Introduction of decoupling capacitor enables charging decoupling between high voltage battery (HVB) and low voltage battery (LVB), thereby simplifying multi-port energy management. Furthermore, minimum current ratio is employed to determine optimal phase shift, achieving minimized conduction losses during HVB charging while maintaining zero voltage switching (ZVS) for all switches. Comprehensive analysis of proposed converter is conducted, covering operational principles, steady-state performance, soft switching characteristics, efficiency and loss breakdown, along with control methodology. Experimental prototype rated at 500W for OBC and 300W for APM is implemented to validate converter performance. Experimental results demonstrate peak system efficiency of 95.3% during simultaneous HVB and LVB charging, and 93.16% during LVB charging alone, confirming effectiveness of proposed converter.
- 22 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 7, 157-172
Open AccessOBC and APM Integration Topology and Decoupling Design for Solar Electric Vehicle
Integration of electric vehicle power conversion units presents a promising solution, yet introduces challenges including inter-port power coupling and compromised efficiency in integrated systems. This paper proposes a photovoltaic compatible integrated converter combining on-board charger (OBC) with auxiliary power module (APM), featuring cost effectiveness and high power density. Introduction of decoupling capacitor enables charging decoupling between high voltage battery (HVB) and low voltage battery (LVB), thereby simplifying multi-port energy management. Furthermore, minimum current ratio is employed to determine optimal phase shift, achieving minimized conduction losses during HVB charging while maintaining zero voltage switching (ZVS) for all switches. Comprehensive analysis of proposed converter is conducted, covering operational principles, steady-state performance, soft switching characteristics, efficiency and loss breakdown, along with control methodology. Experimental prototype rated at 500W for OBC and 300W for APM is implemented to validate converter performance. Experimental results demonstrate peak system efficiency of 95.3% during simultaneous HVB and LVB charging, and 93.16% during LVB charging alone, confirming effectiveness of proposed converter.
- 11 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4679-4690
Expandable High Step-Up Soft-Switching Integrated Boost–SEPIC Converter With Y-Source Coupled Inductor
This article proposes a high step-up soft-switching integrated Boost-Sepic converter with a Y-source coupled inductor for interface circuit of renewable energy power generation systems. By combining the Boost converter, Sepic converter, and Y-source coupled inductor, the converter achieves a higher voltage gain. Additionally, it features low input current ripple and a common ground for both the input and output. A series of multiple switched capacitor units can be cascaded on the output side of the converter, allowing for enhanced flexibility and expandability. The output voltage is shared by three capacitors, which effectively reduces the voltage stress on the capacitors and reduces the size of the capacitors. In addition, the active clamping circuit effectively utilizes the leakage inductance energy, enabling zero-voltage switching (ZVS) for the switch and zero-current switching (ZCS) for the diode, thereby reducing the loss of the switching elements. Since the switch is positioned before the Y-source, the switch also has lower voltage stress and operates over the full duty cycle range. This article presents a detailed analysis of the operating principle and steady-state performance of the converter. A 400W experimental prototype was constructed to validate the correctness and feasibility of the theoretical analysis.
- 11 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4679-4690
Expandable High Step-Up Soft-Switching Integrated Boost–SEPIC Converter With Y-Source Coupled Inductor
This article proposes a high step-up soft-switching integrated Boost-Sepic converter with a Y-source coupled inductor for interface circuit of renewable energy power generation systems. By combining the Boost converter, Sepic converter, and Y-source coupled inductor, the converter achieves a higher voltage gain. Additionally, it features low input current ripple and a common ground for both the input and output. A series of multiple switched capacitor units can be cascaded on the output side of the converter, allowing for enhanced flexibility and expandability. The output voltage is shared by three capacitors, which effectively reduces the voltage stress on the capacitors and reduces the size of the capacitors. In addition, the active clamping circuit effectively utilizes the leakage inductance energy, enabling zero-voltage switching (ZVS) for the switch and zero-current switching (ZCS) for the diode, thereby reducing the loss of the switching elements. Since the switch is positioned before the Y-source, the switch also has lower voltage stress and operates over the full duty cycle range. This article presents a detailed analysis of the operating principle and steady-state performance of the converter. A 400W experimental prototype was constructed to validate the correctness and feasibility of the theoretical analysis.