Yechan Park
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yechan Park has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Chul Kim
Department of Bio and Brain Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, Republic of Korea
5 shared publications - Hongkyun Kim
Department of Bio and Brain Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, South Korea
3 shared publications - Minkyu Je
Korea Advanced Institute of Science and Technology (KAIST)
3 shared publications - Sohmyung Ha
New York University Abu Dhabi
2 shared publications - Changhoon Sung
Department of Bio and Brain Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, Republic of Korea
1 shared publication - Daehyeon Kwon
School of Electrical Engineering, Korea Advanced Institute of Science and Technology, Daejeon, South Korea
1 shared publication
Latest Publications
- 5 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (11) , 3966-3984
A Wireless Power and Data Transfer System for Medical Implants Using a Miniaturized Inductive Link With Frequency-Splitting Enhancement
This article presents an enhanced-frequency-splitting-based wireless power and data transfer (EFS-WPDT) system that simultaneously delivers power and forward data over a compact inductive link. For data transmission, the proposed system employs frequency-shift keying (FSK) based on frequency-splitting enhancement (FSE), which is enabled by dynamic link-load isolation (LLI) and time-interleaved $LC$ resonance. This approach effectively addresses the conventional tradeoffs among power delivered to the load (PDL), data rate (DR), and power transfer efficiency (PTE). The dynamic LLI decouples the load during each resonance phase, which is critical for enabling FSE, and is implemented using a quasi-resonant boost converter (QRBC) that provides a boosted and regulated output voltage. For time-interleaved operation, reliable peak detection is achieved by a body-tuned peak detector (BTPD), which maintains accurate timing across varying link conditions. A frequency-to-amplitude converter enhances sensitivity by amplifying envelope differences, enabling robust data demodulation even in the miniaturized link. The presented ICs, fabricated in a 180-nm bipolar-CMOS-DMOS (BCD) process, simultaneously achieve 60.2% overall PTE, 43.4-mW PDL, and 1-Mb/s DR with a sub-centimeter receiver (RX) coil. As a result, the figure of merit (FoM) for data transmission is improved to a level comparable to previous works using centimeter-scale links, while the FoM for power delivery is improved by $2.5\times $ compared to prior state-of-the-art systems, employing a single inductive link.
- 5 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (11) , 3966-3984
A Wireless Power and Data Transfer System for Medical Implants Using a Miniaturized Inductive Link With Frequency-Splitting Enhancement
This article presents an enhanced-frequency-splitting-based wireless power and data transfer (EFS-WPDT) system that simultaneously delivers power and forward data over a compact inductive link. For data transmission, the proposed system employs frequency-shift keying (FSK) based on frequency-splitting enhancement (FSE), which is enabled by dynamic link-load isolation (LLI) and time-interleaved $LC$ resonance. This approach effectively addresses the conventional tradeoffs among power delivered to the load (PDL), data rate (DR), and power transfer efficiency (PTE). The dynamic LLI decouples the load during each resonance phase, which is critical for enabling FSE, and is implemented using a quasi-resonant boost converter (QRBC) that provides a boosted and regulated output voltage. For time-interleaved operation, reliable peak detection is achieved by a body-tuned peak detector (BTPD), which maintains accurate timing across varying link conditions. A frequency-to-amplitude converter enhances sensitivity by amplifying envelope differences, enabling robust data demodulation even in the miniaturized link. The presented ICs, fabricated in a 180-nm bipolar-CMOS-DMOS (BCD) process, simultaneously achieve 60.2% overall PTE, 43.4-mW PDL, and 1-Mb/s DR with a sub-centimeter receiver (RX) coil. As a result, the figure of merit (FoM) for data transmission is improved to a level comparable to previous works using centimeter-scale links, while the FoM for power delivery is improved by $2.5\times $ compared to prior state-of-the-art systems, employing a single inductive link.
- 19 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (8) , 2568-2580
DiTTO: A Distance Adaptive Over 100-mW Wireless Power Transfer System With 1.695-Mb/s Uplink Telemetry and a Shared Inductor Two-Output Regulating Rectification
This article presents a wireless power transfer (WPT) system that incorporates a seamless uplink data telemetry and a simultaneous shared inductor dual-output (SIDO) regulating rectification (RR) under distance variation over a single WPT link. The proposed double charging keying (DCK) uplink data modulation method assisted by a dynamic zoom control breaks the trade-off between power delivery to the load (PDL) and uplink data such that the high data-rate uplink data telemetry no longer limits the amount of PDLs. Furthermore, DCK alleviates the design difficulty in simultaneous uplink data telemetry and RR. The dynamic ZOOM-based digital control algorithm is employed to ensure reliable uplink data telemetry and rapid transient response of SIDO-RR with two $\Delta \Sigma $ -loops under distance variations. This work achieves 1.695-Mb/s uplink data rate while delivering up to 108 mW to two independent loads over 10–42-mm single-link distance. The chip fabricated in standard 65-nm CMOS occupies 0.2-mm2 active area and its performance is validated through in vivo experiments.
- 19 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (8) , 2568-2580
DiTTO: A Distance Adaptive Over 100-mW Wireless Power Transfer System With 1.695-Mb/s Uplink Telemetry and a Shared Inductor Two-Output Regulating Rectification
This article presents a wireless power transfer (WPT) system that incorporates a seamless uplink data telemetry and a simultaneous shared inductor dual-output (SIDO) regulating rectification (RR) under distance variation over a single WPT link. The proposed double charging keying (DCK) uplink data modulation method assisted by a dynamic zoom control breaks the trade-off between power delivery to the load (PDL) and uplink data such that the high data-rate uplink data telemetry no longer limits the amount of PDLs. Furthermore, DCK alleviates the design difficulty in simultaneous uplink data telemetry and RR. The dynamic ZOOM-based digital control algorithm is employed to ensure reliable uplink data telemetry and rapid transient response of SIDO-RR with two $\Delta \Sigma $ -loops under distance variations. This work achieves 1.695-Mb/s uplink data rate while delivering up to 108 mW to two independent loads over 10–42-mm single-link distance. The chip fabricated in standard 65-nm CMOS occupies 0.2-mm2 active area and its performance is validated through in vivo experiments.
- 28 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (4) , 5576-5585
A 13.56-MHz Wireless Power Transfer System With a Wide Operating Distance and Load Range for Biometric Smartcards
This article presents a wireless power transfer system for an increased dynamic range of link distance and load with extended controllability of transmitting power. Under wide link distance and load variation, rectification and regulation in a single-stage to provide a stable 3 V DC voltage $V_\textrm {L}$ from a 13.56 MHz sinusoidal waveform at the receiver (RX) $LC$ tank is performed. For high end-to-end power transfer efficiency and robust operation under link and load variations, the transmitting power $P_\textrm {TX}$ is controlled by the reflected impedance from the (RX) to the transmitter (TX). To extend the controllability of the $P_\textrm {TX}$ , antennae with high quality factors and a series-connected RX $LC$ tank structure are applied. A working-only-when-needed rising edge detector and a $\Delta \Sigma$ -based falling edge detector for low power and accurate zero current detection are presented. A digital $\Delta \Sigma$ -based voltage regulation controller is adopted for stable DC supply with fast transient response. The implemented IC in a standard 65 nm CMOS process measures 0.14 mm $^{2}$ active silicon area. The proposed work operates under a wide range of link distance (30 mm to 185 mm) with a large load dynamic range (10000×, 60 $\Omega$ - 600 k $\Omega$ ).
- 28 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (4) , 5576-5585
A 13.56-MHz Wireless Power Transfer System With a Wide Operating Distance and Load Range for Biometric Smartcards
This article presents a wireless power transfer system for an increased dynamic range of link distance and load with extended controllability of transmitting power. Under wide link distance and load variation, rectification and regulation in a single-stage to provide a stable 3 V DC voltage $V_\textrm {L}$ from a 13.56 MHz sinusoidal waveform at the receiver (RX) $LC$ tank is performed. For high end-to-end power transfer efficiency and robust operation under link and load variations, the transmitting power $P_\textrm {TX}$ is controlled by the reflected impedance from the (RX) to the transmitter (TX). To extend the controllability of the $P_\textrm {TX}$ , antennae with high quality factors and a series-connected RX $LC$ tank structure are applied. A working-only-when-needed rising edge detector and a $\Delta \Sigma$ -based falling edge detector for low power and accurate zero current detection are presented. A digital $\Delta \Sigma$ -based voltage regulation controller is adopted for stable DC supply with fast transient response. The implemented IC in a standard 65 nm CMOS process measures 0.14 mm $^{2}$ active silicon area. The proposed work operates under a wide range of link distance (30 mm to 185 mm) with a large load dynamic range (10000×, 60 $\Omega$ - 600 k $\Omega$ ).
- 12 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 200-201
A 96.5%-Power-Efficiency Hybrid Buck-Boost Photovoltaic Energy Harvester Employing Adaptive FOCV MPPT Control for >98% MPPT Efficiency Across a 10,000× Dynamic Range
We present a photovoltaic (PV) energy harvesting (EH) system achieving both high maximum-power-point-tracking efficiency (ηMPPT) and high power-conversion efficiency (ηCONV) in an ultra-wide input power (PIN) range. Instead of a complex and power-hungry hybrid MPPT, an MPPT based on an adaptive fractional open-circuit voltage (FOCV) method is used to tune the fraction k based on PIN with little power overhead. Also, a hybrid topology is modified to work as a buck-boost converter to maintain high ηCONV at low PIN by combining three different control techniques. Zero-current-detection (ZCD) is performed with actively changing the tuning resolution to reduce control bit size and response time.
- 12 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 200-201
A 96.5%-Power-Efficiency Hybrid Buck-Boost Photovoltaic Energy Harvester Employing Adaptive FOCV MPPT Control for >98% MPPT Efficiency Across a 10,000× Dynamic Range
We present a photovoltaic (PV) energy harvesting (EH) system achieving both high maximum-power-point-tracking efficiency (ηMPPT) and high power-conversion efficiency (ηCONV) in an ultra-wide input power (PIN) range. Instead of a complex and power-hungry hybrid MPPT, an MPPT based on an adaptive fractional open-circuit voltage (FOCV) method is used to tune the fraction k based on PIN with little power overhead. Also, a hybrid topology is modified to work as a buck-boost converter to maintain high ηCONV at low PIN by combining three different control techniques. Zero-current-detection (ZCD) is performed with actively changing the tuning resolution to reduce control bit size and response time.
- 16 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 15 (6) , 1306-1319
A Wireless Power and Data Transfer IC for Neural Prostheses Using a Single Inductive Link With Frequency-Splitting Characteristic
This paper presents a frequency-splitting-based wireless power and data transfer IC that simultaneously delivers power and forward data over a single inductive link. For data transmission, frequency-shift keying (FSK) is utilized because the FSK modulation scheme supports continuous wireless power transmission without disruption of the carrier amplitude. Moreover, the link that manifests the frequency-splitting characteristic due to a close distance between coupled coils provides wide bandwidth for data delivery without degrading the quality factors of the coils. It results in large power delivery, high data rate, and high power transfer efficiency. The presented IC fabricated in a 180-nm BCD process simultaneously achieves up-to-115-mW wireless power delivery to the load and 2.5-Mb/s downlink data rate over the single inductive link. The measured overall power efficiency from the DC power supply at the transmitter module to the load at the receiver module reaches 56.7$\%$ at its maximum, and the bit error rate is lower than 10$^{-6}$ at 2.5 Mb/s. As a result, the figure of merit (FoM) for data transmission is enhanced by 2 times, and the FoM for power delivery is improved by 38.7 times compared to prior state-of-the-arts using a single inductive link.- 16 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 15 (6) , 1306-1319
A Wireless Power and Data Transfer IC for Neural Prostheses Using a Single Inductive Link With Frequency-Splitting Characteristic
This paper presents a frequency-splitting-based wireless power and data transfer IC that simultaneously delivers power and forward data over a single inductive link. For data transmission, frequency-shift keying (FSK) is utilized because the FSK modulation scheme supports continuous wireless power transmission without disruption of the carrier amplitude. Moreover, the link that manifests the frequency-splitting characteristic due to a close distance between coupled coils provides wide bandwidth for data delivery without degrading the quality factors of the coils. It results in large power delivery, high data rate, and high power transfer efficiency. The presented IC fabricated in a 180-nm BCD process simultaneously achieves up-to-115-mW wireless power delivery to the load and 2.5-Mb/s downlink data rate over the single inductive link. The measured overall power efficiency from the DC power supply at the transmitter module to the load at the receiver module reaches 56.7$\%$ at its maximum, and the bit error rate is lower than 10$^{-6}$ at 2.5 Mb/s. As a result, the figure of merit (FoM) for data transmission is enhanced by 2 times, and the FoM for power delivery is improved by 38.7 times compared to prior state-of-the-arts using a single inductive link.