Ivanna Slobodianiuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ivanna Slobodianiuk has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Victor Maiboroda
КПІ ім. Ігоря Сікорського
3 shared publications - Dmytro Dzhulii
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute
2 shared publications - Yurii Besarabets
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute
2 shared publications Kostiantyn Zastavskyi
1 shared publicationKristina Poznjak
Technical University of Ukraine «Igor Sikorsky Kyiv Polytechnic Institute
1 shared publication- Nataliia Havrushkevych
КПІ ім. Ігоря Сікорського
1 shared publication
Latest Publications
- Open Access
- 14 May 2024
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Біомедична інженерія і технологія
- No. 14,p. 8-17
ВИГОТОВЛЕННЯ ПРОТЕЗІВ НИЖНІХ КІНЦІВОК: ВИКЛИКИ, АНАЛІЗ ТА МОЖЛИВІ РІШЕННЯ
Наразі наша країна стикається з багатьма викликами, на які ми спрямовуємо максимальні зусилля та увагу для їх вирішення. Серед головних завдань - відновлення людських ресурсів, економічна реабілітація після конфлікту, соціальна реінтеграція постраждалих від військових дій та забезпечення повноцінного життя. У прифронтових зонах, особливо там, де проходять активні бойові дії, багато людей стикаються з ризиком серйозних травм. Наслідком цього може бути повна або часткова втрата кінцівок. Це ставить перед медичною та науковою спільнотами складні завдання щодо забезпечення необхідної підтримки і реабілітації постраждалим. Тож у даній статті увага зосереджується на важливості виробництва куксоприймачів, які є ключовими компонентами в конструкції протезів нижніх кінцівок. Основна увага приділяється необхідності персоналізації та точності у їх виробництві, особливо в контексті зростаючої кількості ампутацій, що вимагає ревізії та оптимізації застарілих технологічних процесів. Авторами було переглянуто існуючі підходи та інноваційні методи, зокрема адитивні технології, які можуть сприяти ефективнішому виробництву та покращенню якості протезних виробів. Також у статті обговорюються різні матеріали для гільз, методи фіксації та вплив цих аспектів на комфорт та функціональність протезів. Дослідження і рекомендації, представлені в статті, мають на меті сприяти подальшому розвитку галузі протезування в Україні, покращенню якості життя постраждалих та їхній соціальній адаптації та реінтеграції. Важливою частиною аналізу є розгляд основних параметрів, які впливають на ефективність і прийнятність протезів. Запропоновано інженерні підходи, спрямовані на розв'язання цих критичних проблем
- 14 May 2024
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Біомедична інженерія і технологія
- No. 14,p. 8-17
Open AccessВИГОТОВЛЕННЯ ПРОТЕЗІВ НИЖНІХ КІНЦІВОК: ВИКЛИКИ, АНАЛІЗ ТА МОЖЛИВІ РІШЕННЯ
Наразі наша країна стикається з багатьма викликами, на які ми спрямовуємо максимальні зусилля та увагу для їх вирішення. Серед головних завдань - відновлення людських ресурсів, економічна реабілітація після конфлікту, соціальна реінтеграція постраждалих від військових дій та забезпечення повноцінного життя. У прифронтових зонах, особливо там, де проходять активні бойові дії, багато людей стикаються з ризиком серйозних травм. Наслідком цього може бути повна або часткова втрата кінцівок. Це ставить перед медичною та науковою спільнотами складні завдання щодо забезпечення необхідної підтримки і реабілітації постраждалим. Тож у даній статті увага зосереджується на важливості виробництва куксоприймачів, які є ключовими компонентами в конструкції протезів нижніх кінцівок. Основна увага приділяється необхідності персоналізації та точності у їх виробництві, особливо в контексті зростаючої кількості ампутацій, що вимагає ревізії та оптимізації застарілих технологічних процесів. Авторами було переглянуто існуючі підходи та інноваційні методи, зокрема адитивні технології, які можуть сприяти ефективнішому виробництву та покращенню якості протезних виробів. Також у статті обговорюються різні матеріали для гільз, методи фіксації та вплив цих аспектів на комфорт та функціональність протезів. Дослідження і рекомендації, представлені в статті, мають на меті сприяти подальшому розвитку галузі протезування в Україні, покращенню якості життя постраждалих та їхній соціальній адаптації та реінтеграції. Важливою частиною аналізу є розгляд основних параметрів, які впливають на ефективність і прийнятність протезів. Запропоновано інженерні підходи, спрямовані на розв'язання цих критичних проблем
- Open Access
- 1 October 2022
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 2,p. 16-22
INVESTIGATION OF THE DRAG FORCES ARISING IN THE MAGNETO-ABRASIVE TOOL DURING THE FINISHING OF CYLINDRICAL PARTS IN THE ANNULAR BATH
The method has been developed and systematic studies have been carried out to measure the drag forces, that exerted by a magneto-abrasive tool on machined cylindrical parts with a diameter of 16 mm and the height of 30 mm, made of para-, ferro- and diamagnetic materials, in an annular working zone with the diameter of 200 mm with the working height of 30 mm at machining speeds in the range of 1 - 3 m / s, magnetic induction in the working areas varying in the range of 0.2 - 0.25 T. It is shown that the drag forces significantly depend on the magnetic and rheological properties of the magneto-abrasive tool. During magneto-abrasive finishing (MAF), the drag force for non-magnetic parts is almost the same and does not depend on the machining speed, and with an increase in magnetic induction in the working areas, its linear growth takes place. The coefficient of magnification of drag force determined by the magnetic field, for powders with a particle size of 400/315 µm is 960 N/T, and for a size of 200/100 µm it is 720 N/T. It is shown that the drag forces during the MAF of ferromagnetic parts vary in the range from 160 to 220 N and are 1.2–1.45 times higher than for non-magnetic parts, which is due to the action of forces of magnetic origin, the features of the interaction of structural elements of MAT with machined surfaces and the formation of blocking up zones between the surface of the part and the pole pieces of the annular bath. The periodic change in the drag forces of the MAT of the workpiece was established near their average value, and at elevated MAF speeds of more than 2–2.5 m/s, instabilities were recorded associated with a periodic decrease in the oscillation amplitudes of the drag forces as a result of rearrangement, changes in the dimensions and volumes of the structural elements of the magneto-abrasive tool and the conditions of their interaction with the machined surfaces.
- 1 October 2022
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 2,p. 16-22
Open AccessINVESTIGATION OF THE DRAG FORCES ARISING IN THE MAGNETO-ABRASIVE TOOL DURING THE FINISHING OF CYLINDRICAL PARTS IN THE ANNULAR BATH
The method has been developed and systematic studies have been carried out to measure the drag forces, that exerted by a magneto-abrasive tool on machined cylindrical parts with a diameter of 16 mm and the height of 30 mm, made of para-, ferro- and diamagnetic materials, in an annular working zone with the diameter of 200 mm with the working height of 30 mm at machining speeds in the range of 1 - 3 m / s, magnetic induction in the working areas varying in the range of 0.2 - 0.25 T. It is shown that the drag forces significantly depend on the magnetic and rheological properties of the magneto-abrasive tool. During magneto-abrasive finishing (MAF), the drag force for non-magnetic parts is almost the same and does not depend on the machining speed, and with an increase in magnetic induction in the working areas, its linear growth takes place. The coefficient of magnification of drag force determined by the magnetic field, for powders with a particle size of 400/315 µm is 960 N/T, and for a size of 200/100 µm it is 720 N/T. It is shown that the drag forces during the MAF of ferromagnetic parts vary in the range from 160 to 220 N and are 1.2–1.45 times higher than for non-magnetic parts, which is due to the action of forces of magnetic origin, the features of the interaction of structural elements of MAT with machined surfaces and the formation of blocking up zones between the surface of the part and the pole pieces of the annular bath. The periodic change in the drag forces of the MAT of the workpiece was established near their average value, and at elevated MAF speeds of more than 2–2.5 m/s, instabilities were recorded associated with a periodic decrease in the oscillation amplitudes of the drag forces as a result of rearrangement, changes in the dimensions and volumes of the structural elements of the magneto-abrasive tool and the conditions of their interaction with the machined surfaces.
- Open Access
- 28 July 2022
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1,p. 66-73
SPECIFIC FEATURES OF MAGNETO-ABRASIVE MACHINING OF CARBIDE TOOLS WITH PROTECTIVE CHAMFERS ON THE CUTTING EDGES
To ensure the durability and working ability of cutting tools, especially carbide, it is promising to form a rational microgeometry of working surfaces, in particular, the shape and geometry of cutting edges, as well as their hardening. For this, it is necessary to carry out additional machining of the tool after its sharpening operation. The magneto-abrasive machining method in conditions of large working gaps with a rational ratio of the impact and frictional interaction of the magneto-abrasive tool with the machined elements makes it possible to form microgeometry and strengthen both the cutting edges and the working surfaces. To ensure effective machining, it is necessary to determine the regularities of forming the microgeometry of the cutting edges with pre-made protective chamfers. The paper presents the results of a complex study of the magneto-abrasive machining process of carbide not sharpened inserts with protective chamfers on the cutting edges made at different angles. It was shown that the process of edge rounding is linearly related to the duration of magneto-abrasive machining. Moreover, the rate of increase in the size of the radius of cutting edges rounding with protective chamfers increases linearly with an increase in the angle of inclination of the chamfers, all other process conditions being equal. The physical description of the hardening mechanism of the surface layer of the working elements of the carbide cutting tool was proposed. It was shown that the hardening process is associated with the rational imposition of forces arising as a result of the frictional and impact interaction of the particles and the formations of the magneto-abrasive tool with the machined surfaces. It was found that the nature of the change in surface hardness obtained after magneto-abrasive machining on the protective chamfers has the wavy shape depending on the time of the process. The greatest increase in surface hardness takes place on chamfers made at angles of 10 ° and 20 ° and is explained by the value of the ratio between the forces of normal and tangential origin arising from the contact of the magneto-abrasive tool with the machined surfaces.
- 28 July 2022
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1,p. 66-73
Open AccessSPECIFIC FEATURES OF MAGNETO-ABRASIVE MACHINING OF CARBIDE TOOLS WITH PROTECTIVE CHAMFERS ON THE CUTTING EDGES
To ensure the durability and working ability of cutting tools, especially carbide, it is promising to form a rational microgeometry of working surfaces, in particular, the shape and geometry of cutting edges, as well as their hardening. For this, it is necessary to carry out additional machining of the tool after its sharpening operation. The magneto-abrasive machining method in conditions of large working gaps with a rational ratio of the impact and frictional interaction of the magneto-abrasive tool with the machined elements makes it possible to form microgeometry and strengthen both the cutting edges and the working surfaces. To ensure effective machining, it is necessary to determine the regularities of forming the microgeometry of the cutting edges with pre-made protective chamfers. The paper presents the results of a complex study of the magneto-abrasive machining process of carbide not sharpened inserts with protective chamfers on the cutting edges made at different angles. It was shown that the process of edge rounding is linearly related to the duration of magneto-abrasive machining. Moreover, the rate of increase in the size of the radius of cutting edges rounding with protective chamfers increases linearly with an increase in the angle of inclination of the chamfers, all other process conditions being equal. The physical description of the hardening mechanism of the surface layer of the working elements of the carbide cutting tool was proposed. It was shown that the hardening process is associated with the rational imposition of forces arising as a result of the frictional and impact interaction of the particles and the formations of the magneto-abrasive tool with the machined surfaces. It was found that the nature of the change in surface hardness obtained after magneto-abrasive machining on the protective chamfers has the wavy shape depending on the time of the process. The greatest increase in surface hardness takes place on chamfers made at angles of 10 ° and 20 ° and is explained by the value of the ratio between the forces of normal and tangential origin arising from the contact of the magneto-abrasive tool with the machined surfaces.
- Open Access
- 1 January 2021
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 3(25),p. 9-16
ЗАСТОСУВАННЯ МАГНІТНО-АБРАЗИВНОГО ОБРОБЛЕННЯ СТОМАТОЛОГІЧНОГО ІНСТРУМЕНТУ БАГАТОРАЗОВОГО ВИКОРИСТАННЯ ДЛЯ ВІДНОВЛЕННЯ ЙОГО ВЛАСТИВОСТЕЙ
На основі аналізу особливостей процесу експлуатації та подальшого циклу оброблення стоматологічних борфрез багаторазового використання представлено обґрунтування можливості застосування на етапі передстерилізаціного очищення методу магнітно-абразивного оброблення поверхонь робочих частин твердосплавних борів кулеподібної форми. Виконано аналіз стану поверхні та параметрів шорсткості робочих поверхонь борфрез до та після магнітно-абразивного оброблення. Надані рекомендації щодо часу оброблення та діапазонів розмірів різальних кромок борів, що забезпечують збільшення термінів експлуатації.
- 1 January 2021
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 3(25),p. 9-16
Open AccessЗАСТОСУВАННЯ МАГНІТНО-АБРАЗИВНОГО ОБРОБЛЕННЯ СТОМАТОЛОГІЧНОГО ІНСТРУМЕНТУ БАГАТОРАЗОВОГО ВИКОРИСТАННЯ ДЛЯ ВІДНОВЛЕННЯ ЙОГО ВЛАСТИВОСТЕЙ
На основі аналізу особливостей процесу експлуатації та подальшого циклу оброблення стоматологічних борфрез багаторазового використання представлено обґрунтування можливості застосування на етапі передстерилізаціного очищення методу магнітно-абразивного оброблення поверхонь робочих частин твердосплавних борів кулеподібної форми. Виконано аналіз стану поверхні та параметрів шорсткості робочих поверхонь борфрез до та після магнітно-абразивного оброблення. Надані рекомендації щодо часу оброблення та діапазонів розмірів різальних кромок борів, що забезпечують збільшення термінів експлуатації.