Aditi Thanki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aditi Thanki has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Han Haitjema
KU Leuven
4 shared publications Abdellatif Bey-Temsamani
2 shared publicationsAnn Witvrouw
2 shared publications- Ann Witvrouw
IMEC, Leuven, Belgium
2 shared publications - Abdellatif Bey-Temsamani
Flanders Make, Gaston Geenslaan 8, 3001 Heverlee, Belgium
1 shared publication - Adam Thompson
University of Nottingham
1 shared publication
Latest Publications
- Open Access
Optimisation of Imaging Confocal Microscopy for Topography Measurements of Metal Additive Surfaces
Additive manufactured surfaces, especially metal powder bed fusion surfaces, present unique challenges for measurement because of their complex topographies. To address these measurement challenges, optimisation of the measurement process is required. Using a statistical approach, sensitivity analyses were performed on measurement settings found on a commercial programmable array scanning confocal microscope. The instrument measurement process parameters were compared by their effects on three quality indicators: the areal surface texture parameter Sa, measurement noise, and number of non-measured points. An analysis was performed using a full factorial design of experiments for both the top and side surfaces of test surfaces made from Inconel 718 and Ti-6Al-4V using powder bed fusion. The results indicated that measurements of metal additive surfaces are robust to changes in the measurement control parameters for Sa, with variations within 5% of the mean parameter value for the same objective, surface, and measured area. The number of non-measured points and the measurement noise were more varied and were affected by the choice of measurement control parameters, but such changes could be predicted by the statistical models. The contribution offered by this work is an increased understanding of imaging confocal microscopy measurement of metal additive surfaces, along with the establishment of good practice guidance for measurements.
Open AccessOptimisation of Imaging Confocal Microscopy for Topography Measurements of Metal Additive Surfaces
Additive manufactured surfaces, especially metal powder bed fusion surfaces, present unique challenges for measurement because of their complex topographies. To address these measurement challenges, optimisation of the measurement process is required. Using a statistical approach, sensitivity analyses were performed on measurement settings found on a commercial programmable array scanning confocal microscope. The instrument measurement process parameters were compared by their effects on three quality indicators: the areal surface texture parameter Sa, measurement noise, and number of non-measured points. An analysis was performed using a full factorial design of experiments for both the top and side surfaces of test surfaces made from Inconel 718 and Ti-6Al-4V using powder bed fusion. The results indicated that measurements of metal additive surfaces are robust to changes in the measurement control parameters for Sa, with variations within 5% of the mean parameter value for the same objective, surface, and measured area. The number of non-measured points and the measurement noise were more varied and were affected by the choice of measurement control parameters, but such changes could be predicted by the statistical models. The contribution offered by this work is an increased understanding of imaging confocal microscopy measurement of metal additive surfaces, along with the establishment of good practice guidance for measurements.
- Open Access
- 28 September 2022
- Published by Springer Nature in Research Square
Off-axis high-speed camera-based real-time monitoring and simulation study for laser powder bed fusion of 316L stainless steel
In-situ monitoring and post-process metrology form a basis to better understand the fundamental physics involved in the Laser Powder Bed Fusion (LPBF) process and ultimately to determine its stability. By utilizing high-speed imaging, various process signatures are produced during single track formation of 316L stainless steel with various combinations of laser power and scan speed. In this study, we evaluate whether these signatures can be used to detect the onset of potential defects. To identify process signatures, image segmentation and feature detection are applied to the monitoring data along the line scans. The process signatures determined in the current study are mainly related to the features like the process zone length-to-width ratio, process zone area, process zone mean intensity, spatter speed and number of spatters. It is shown that the scan speed has a significant impact on the process stability and spatter formation during single track fusion. Simulations with similar processing conditions were also performed to predict melt pool geometric features. Post-process characterization techniques such as X-ray computed tomography and 2.5-D surface topography measurement were carried out for a quality check of the line track. An attempt was made to correlate physics-based features with process-related defects and a correlation between the number of keyhole porosities and the number of spatters was observed for the line tracks.
- 28 September 2022
- Published by Springer Nature in Research Square
Open AccessOff-axis high-speed camera-based real-time monitoring and simulation study for laser powder bed fusion of 316L stainless steel
In-situ monitoring and post-process metrology form a basis to better understand the fundamental physics involved in the Laser Powder Bed Fusion (LPBF) process and ultimately to determine its stability. By utilizing high-speed imaging, various process signatures are produced during single track formation of 316L stainless steel with various combinations of laser power and scan speed. In this study, we evaluate whether these signatures can be used to detect the onset of potential defects. To identify process signatures, image segmentation and feature detection are applied to the monitoring data along the line scans. The process signatures determined in the current study are mainly related to the features like the process zone length-to-width ratio, process zone area, process zone mean intensity, spatter speed and number of spatters. It is shown that the scan speed has a significant impact on the process stability and spatter formation during single track fusion. Simulations with similar processing conditions were also performed to predict melt pool geometric features. Post-process characterization techniques such as X-ray computed tomography and 2.5-D surface topography measurement were carried out for a quality check of the line track. An attempt was made to correlate physics-based features with process-related defects and a correlation between the number of keyhole porosities and the number of spatters was observed for the line tracks.
- 28 February 2022
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 10 (1) , 015025
Stylus tip radius and wear estimation using the Rsk or the Rp and Rv parameter of a sine wave (Type C1) standard
Determination of the stylus tip radius and its wear or damage is a classical problem in tactile surface topography measurements. The determination of the stylus geometry may be tedious and inconvenient, therefore we looked for an easily applicable method. This study shows that the Rsk parameter and the difference between the Rv and Rp parameter may indicate the stylus tip radius as well as wear when using a sine-wave profile material measure, which is commonly supplied with a roughness tester for calibrating and/or adjusting the vertical amplification coefficient. This effect is derived from theoretical calculations on real and simulated styli and specimens and verified experimentally using two commonly used specimens and stylus tips with radii of nominally 1, 2, 5, and 10 µm. When using a standardized stylus with a nominal 2 µm tip radius and 60° cone angle on a typical C1 reference specimen with nominal parameters Ra = 3 µm and RSm = 100 µm, the Rsk value should be approximately −0.01. Any stylus wear will decrease the measured Rsk value. When the Rsk value decreases to a value of −0.06 or lower it may be time for closer inspection and/or replacement of the stylus.
- 28 February 2022
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 10 (1) , 015025
Stylus tip radius and wear estimation using the Rsk or the Rp and Rv parameter of a sine wave (Type C1) standard
Determination of the stylus tip radius and its wear or damage is a classical problem in tactile surface topography measurements. The determination of the stylus geometry may be tedious and inconvenient, therefore we looked for an easily applicable method. This study shows that the Rsk parameter and the difference between the Rv and Rp parameter may indicate the stylus tip radius as well as wear when using a sine-wave profile material measure, which is commonly supplied with a roughness tester for calibrating and/or adjusting the vertical amplification coefficient. This effect is derived from theoretical calculations on real and simulated styli and specimens and verified experimentally using two commonly used specimens and stylus tips with radii of nominally 1, 2, 5, and 10 µm. When using a standardized stylus with a nominal 2 µm tip radius and 60° cone angle on a typical C1 reference specimen with nominal parameters Ra = 3 µm and RSm = 100 µm, the Rsk value should be approximately −0.01. Any stylus wear will decrease the measured Rsk value. When the Rsk value decreases to a value of −0.06 or lower it may be time for closer inspection and/or replacement of the stylus.
- Open Access
- 7 January 2022
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 33 (4) , 045602
3D total variation denoising in X-CT imaging applied to pore extraction in additively manufactured parts
X-ray computed tomography (X-CT) plays an important role in non-destructive quality inspection and process evaluation in metal additive manufacturing, as several types of defects such as keyhole and lack of fusion pores can be observed in these 3D images as local changes in material density. Segmentation of these defects often relies on threshold methods applied to the reconstructed attenuation values of the 3D image voxels. However, the segmentation accuracy is affected by unavoidable X-CT reconstruction features such as partial volume effects, voxel noise and imaging artefacts. These effects create false positives, difficulties in threshold value selection and unclear or jagged defect edges. In this paper, we present a new X-CT defect segmentation method based on preprocessing the X-CT image with a 3D total variation denoising method. By comparing the changes in the histogram, threshold selection can be significantly better, and the resulting segmentation is of much higher quality. We derive the optimal algorithm parameter settings and demonstrate robustness for deviating settings. The technique is presented on simulated data sets, compared between low- and high-quality X-CT scans, and evaluated with optical microscopy after destructive tests.
- 7 January 2022
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 33 (4) , 045602
Open Access3D total variation denoising in X-CT imaging applied to pore extraction in additively manufactured parts
X-ray computed tomography (X-CT) plays an important role in non-destructive quality inspection and process evaluation in metal additive manufacturing, as several types of defects such as keyhole and lack of fusion pores can be observed in these 3D images as local changes in material density. Segmentation of these defects often relies on threshold methods applied to the reconstructed attenuation values of the 3D image voxels. However, the segmentation accuracy is affected by unavoidable X-CT reconstruction features such as partial volume effects, voxel noise and imaging artefacts. These effects create false positives, difficulties in threshold value selection and unclear or jagged defect edges. In this paper, we present a new X-CT defect segmentation method based on preprocessing the X-CT image with a 3D total variation denoising method. By comparing the changes in the histogram, threshold selection can be significantly better, and the resulting segmentation is of much higher quality. We derive the optimal algorithm parameter settings and demonstrate robustness for deviating settings. The technique is presented on simulated data sets, compared between low- and high-quality X-CT scans, and evaluated with optical microscopy after destructive tests.
- Open Access
- 20 December 2021
- Published by Springer Nature in Research Square
Melt Pool Features Analysis Using a High Speed Coaxial Monitoring System for Laser Powder Bed Fusion of Ti-6Al-4V Grade 23
In laser powder bed fusion (LPBF), defects such as pores or cracks can seriously affect the final part quality and lifetime. Keyhole porosity, being one type of porosity defects in LPBF, results from excessive energy density which may be due to changes in process parameters (laser power and scan speed) and/or result from the part’s geometry and/or hatching strategies. To study the possible occurrence of keyhole pores, experimental work as well as simulations were carried out for optimum and high volumetric energy density conditions in Ti-6Al-4V grade 23. By decreasing the scanning speed from 1000 mm/s to 500 mm/s for a fixed laser power of 170 W, keyhole porosities are formed and later observed by X-ray computed tomography. Melt pool images are recorded in real-time during the LPBF process by using a high speed coaxial Near-Infrared (NIR) camera monitoring system. The recorded images are then pre-processed using a set of image processing steps to generate binary images. From the binary images, geometrical features of the melt pool and features that characterize the spatter particles formation and ejection from the melt pool are calculated. The experimental data clearly show spatter patterns in case of keyhole porosity formation at low scan speed. A correlation between the number of pores and the amount of spatter is observed. Besides the experimental work, a previously developed, high fidelity finite volume numerical model was used to simulate the melt pool dynamics with similar process parameters as in the experiment. Simulation results illustrate and confirm the keyhole porosity formation by decreasing laser scan speed.
- 20 December 2021
- Published by Springer Nature in Research Square
Open AccessMelt Pool Features Analysis Using a High Speed Coaxial Monitoring System for Laser Powder Bed Fusion of Ti-6Al-4V Grade 23
In laser powder bed fusion (LPBF), defects such as pores or cracks can seriously affect the final part quality and lifetime. Keyhole porosity, being one type of porosity defects in LPBF, results from excessive energy density which may be due to changes in process parameters (laser power and scan speed) and/or result from the part’s geometry and/or hatching strategies. To study the possible occurrence of keyhole pores, experimental work as well as simulations were carried out for optimum and high volumetric energy density conditions in Ti-6Al-4V grade 23. By decreasing the scanning speed from 1000 mm/s to 500 mm/s for a fixed laser power of 170 W, keyhole porosities are formed and later observed by X-ray computed tomography. Melt pool images are recorded in real-time during the LPBF process by using a high speed coaxial Near-Infrared (NIR) camera monitoring system. The recorded images are then pre-processed using a set of image processing steps to generate binary images. From the binary images, geometrical features of the melt pool and features that characterize the spatter particles formation and ejection from the melt pool are calculated. The experimental data clearly show spatter patterns in case of keyhole porosity formation at low scan speed. A correlation between the number of pores and the amount of spatter is observed. Besides the experimental work, a previously developed, high fidelity finite volume numerical model was used to simulate the melt pool dynamics with similar process parameters as in the experiment. Simulation results illustrate and confirm the keyhole porosity formation by decreasing laser scan speed.
- Open Access
- 1 March 2019
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 24 (3)
Study of keyhole-porosities in selective laser melting using X-ray computed tomography
The Largest Portal of Nondestructive Testing (NDT) Open Access Archive, Conference Proceedings, Journal Articles, News, Products, Services. Professional Networking, Exhibition, Forums, Jobs
- 1 March 2019
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 24 (3)
Open AccessStudy of keyhole-porosities in selective laser melting using X-ray computed tomography
The Largest Portal of Nondestructive Testing (NDT) Open Access Archive, Conference Proceedings, Journal Articles, News, Products, Services. Professional Networking, Exhibition, Forums, Jobs