Chen Li
Chen Li has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Xinquan Zhang
Institute of Standard Process and Material Design, AVIC The First Aircraft Institute, Xi’an 710089, China
3 shared publications - Hao Wang
Department of Materials Science and Engineering, Beihang University, Beijing, CHINA
2 shared publications - Lina Jia
School of Materials Science and Engineering Beihang University 100191 Beijing China
2 shared publications Chengtong Ye
Department of Materials Science and Engineering, Beihang University, Beijing, CHINA
1 shared publication- Chengtong Ye
Beihang Univ, Dept Mat Sci & Engn, Beijing 100191, Peoples R China
1 shared publication - Chuanwei Luo
School of Mechanical and Electrical Engineering, Central South University, Changsha 410083, China
1 shared publication
Latest Publications
- Open Access
Study on Rheological Behavior and Hot Processing Maps of a Novel Ultra-Low Carbon High-Strength Stainless Steel
This study investigated the hot deformation behavior of a novel ultra-low carbon high-strength stainless steel through single-pass isothermal hot compression tests using a Gleeble-3800 thermomechanical simulator. The hot deformation behavior were examined under deformation temperatures ranging from 900 to 1150 °C, true strains of 0.2 to 0.8, and strain rates of 0.01 to 10 s−1. The differences in recrystallization mechanisms under various strain rates were analyzed. Based on the Dynamic Materials Model (DMM) theory, hot processing maps at true strains of 0.2, 0.4, 0.6, and 0.8 were constructed. And the applicability of the Prasad and Murty instability criteria to this new steel was compared. The results indicate that different recrystallization mechanisms operate at different strain rates. Compared to the commonly used Prasad criterion, the Murty instability criterion aligns better with the experimental observations for this steel. The optimal hot processing window for this new steel is identified as a temperature range of 1100–1150 °C with strain rates of 0.1–1 s−1 and 10 s−1, which is consistent with the microstructure of the deformed specimens. This work offers fundamental insights into the microstructural evolution, which is essential for optimizing the hot-working properties of next-generation high-strength stainless steels.
Open AccessStudy on Rheological Behavior and Hot Processing Maps of a Novel Ultra-Low Carbon High-Strength Stainless Steel
This study investigated the hot deformation behavior of a novel ultra-low carbon high-strength stainless steel through single-pass isothermal hot compression tests using a Gleeble-3800 thermomechanical simulator. The hot deformation behavior were examined under deformation temperatures ranging from 900 to 1150 °C, true strains of 0.2 to 0.8, and strain rates of 0.01 to 10 s−1. The differences in recrystallization mechanisms under various strain rates were analyzed. Based on the Dynamic Materials Model (DMM) theory, hot processing maps at true strains of 0.2, 0.4, 0.6, and 0.8 were constructed. And the applicability of the Prasad and Murty instability criteria to this new steel was compared. The results indicate that different recrystallization mechanisms operate at different strain rates. Compared to the commonly used Prasad criterion, the Murty instability criterion aligns better with the experimental observations for this steel. The optimal hot processing window for this new steel is identified as a temperature range of 1100–1150 °C with strain rates of 0.1–1 s−1 and 10 s−1, which is consistent with the microstructure of the deformed specimens. This work offers fundamental insights into the microstructural evolution, which is essential for optimizing the hot-working properties of next-generation high-strength stainless steels.
- Open Access
Study on Quench Sensitivity during Isothermal Treatment of 7A65 Aluminum Alloy
The quenching sensitivity of 7A65 aluminum alloy was investigated using interrupted quenching experiments. The time–temperature transformation (TTT) and time–temperature performance (TTP) curves of the alloy were determined. The results indicate that the nose temperature is about 320 °C and the quenching sensitivity temperature range is from 240 °C to 360 °C. During the isothermal treatment, the supersaturated solid solution resolves to the equilibrium phase of η (MgZn2), and the precipitation rate is the largest at about 320 °C. Through transmission electron microscope (TEM) observation and X-ray diffraction (XRD) tests, it was found that with the extension of the isothermal holding time, the originally dispersed η’ phase gradually decreases until disappear, and the number of η phase increases and gradually grows up at the grain boundary or around the Al3Zr particles. The rod-like η phase at the grain boundary is distributed from discontinuous distribution to chain-like continuous distribution, and the precipitation free zone (PFZ) is gradually generated and widened as the holding time is extended. At the nose temperature, the driving force of nucleation is high, and the diffusion rate is fast, which promotes the precipitation and growth of η phases. The coarse η phase weakens the mechanical properties. According to the results, it is recommended to increase the cooling rate at the sensitivity temperature range to reduce the precipitation of the η phase and decrease the quenching cooling rate from solution temperature to 360 °C to reduce residual stresses in the components.
Open AccessStudy on Quench Sensitivity during Isothermal Treatment of 7A65 Aluminum Alloy
The quenching sensitivity of 7A65 aluminum alloy was investigated using interrupted quenching experiments. The time–temperature transformation (TTT) and time–temperature performance (TTP) curves of the alloy were determined. The results indicate that the nose temperature is about 320 °C and the quenching sensitivity temperature range is from 240 °C to 360 °C. During the isothermal treatment, the supersaturated solid solution resolves to the equilibrium phase of η (MgZn2), and the precipitation rate is the largest at about 320 °C. Through transmission electron microscope (TEM) observation and X-ray diffraction (XRD) tests, it was found that with the extension of the isothermal holding time, the originally dispersed η’ phase gradually decreases until disappear, and the number of η phase increases and gradually grows up at the grain boundary or around the Al3Zr particles. The rod-like η phase at the grain boundary is distributed from discontinuous distribution to chain-like continuous distribution, and the precipitation free zone (PFZ) is gradually generated and widened as the holding time is extended. At the nose temperature, the driving force of nucleation is high, and the diffusion rate is fast, which promotes the precipitation and growth of η phases. The coarse η phase weakens the mechanical properties. According to the results, it is recommended to increase the cooling rate at the sensitivity temperature range to reduce the precipitation of the η phase and decrease the quenching cooling rate from solution temperature to 360 °C to reduce residual stresses in the components.
- Open Access
Quenched Residual Stress Reduction in Pentagon-Curved Aluminum Alloy Forgings Using the Bulging Process
Quenched residual stress in pentagon-curved forgings (PCGs) often leads to severe deformation during subsequent machining operations. This study aims to mitigate the quenched residual stress in PCGs through the implementation of the bulging method. The edge distance ratio (e/D), a geometric characteristic of PCGs, is defined and considered in the established thermo-mechanical model, which incorporates the effects of quenched residual stress. Increasing e/D resulted in amplified maximum internal stresses and surface stresses. To address this issue, a bulging finite element (FE) model was developed to effectively alleviate the quenched residual stress. The stress reduction in surface stress and internal stress was qualified using average stress reduction () and peak stress reduction (), respectively. Notably, stress reduction exhibited an inverse relationship with e/D, indicating that decreasing e/D yields greater stress reduction. Furthermore, an overall stress reduction assessment was conducted for different bulging ratios, revealing that the stress reduction increased as the bulging ratio increased. A comprehensive comparison of different bulging ratios highlighted 2% as the most optimal bulging ratio for stress reduction in PCGs. X-ray diffraction measurement and the contour method were employed to determine surface stress and internal stress, respectively. The experimental results were in agreement with the simulation outcomes, validating the high accuracy of the FE model.Open AccessQuenched Residual Stress Reduction in Pentagon-Curved Aluminum Alloy Forgings Using the Bulging Process
Quenched residual stress in pentagon-curved forgings (PCGs) often leads to severe deformation during subsequent machining operations. This study aims to mitigate the quenched residual stress in PCGs through the implementation of the bulging method. The edge distance ratio (e/D), a geometric characteristic of PCGs, is defined and considered in the established thermo-mechanical model, which incorporates the effects of quenched residual stress. Increasing e/D resulted in amplified maximum internal stresses and surface stresses. To address this issue, a bulging finite element (FE) model was developed to effectively alleviate the quenched residual stress. The stress reduction in surface stress and internal stress was qualified using average stress reduction () and peak stress reduction (), respectively. Notably, stress reduction exhibited an inverse relationship with e/D, indicating that decreasing e/D yields greater stress reduction. Furthermore, an overall stress reduction assessment was conducted for different bulging ratios, revealing that the stress reduction increased as the bulging ratio increased. A comprehensive comparison of different bulging ratios highlighted 2% as the most optimal bulging ratio for stress reduction in PCGs. X-ray diffraction measurement and the contour method were employed to determine surface stress and internal stress, respectively. The experimental results were in agreement with the simulation outcomes, validating the high accuracy of the FE model. - Open Access
Effect of the Initial Texture, Recrystallization and Re-Dissolution Process on the Evolution of Texture during Solution Treatment of the 7A65 Hot Rolled Plate
The evolution of textures, the degree of recrystallization and the mechanical properties of 7A65 hot rolled plates during re-dissolution were studied with different thicknesses (25 mm, 65 mm, 120 mm) and different degrees of deformation. It was found that different plates exhibited different trends of re-dissolution because the degrees of deformation increased and the degrees of recrystallization were different during the solution treatment. With the increase of deformation and static recrystallization degrees, texture types changed from Cube, R-Cube to Brass, R, Cube and Copper during the re-dissolution process. The value of the Schmid factor was calculated and the value along the rolling direction was significantly larger than along the transverse direction, which led to a lower yield strength along the rolling direction. In terms of the average contribution of the yield strength, the strengthening of the grain boundary including LAGBs (low-angle grain boundaries) was found to play a more significant role than the effect of solid atoms and dislocation densities. Therefore, the 25 mm plate exhibits the best mechanical properties, with a yield strength of 565.7 MPa along the rolling direction.Open AccessEffect of the Initial Texture, Recrystallization and Re-Dissolution Process on the Evolution of Texture during Solution Treatment of the 7A65 Hot Rolled Plate
The evolution of textures, the degree of recrystallization and the mechanical properties of 7A65 hot rolled plates during re-dissolution were studied with different thicknesses (25 mm, 65 mm, 120 mm) and different degrees of deformation. It was found that different plates exhibited different trends of re-dissolution because the degrees of deformation increased and the degrees of recrystallization were different during the solution treatment. With the increase of deformation and static recrystallization degrees, texture types changed from Cube, R-Cube to Brass, R, Cube and Copper during the re-dissolution process. The value of the Schmid factor was calculated and the value along the rolling direction was significantly larger than along the transverse direction, which led to a lower yield strength along the rolling direction. In terms of the average contribution of the yield strength, the strengthening of the grain boundary including LAGBs (low-angle grain boundaries) was found to play a more significant role than the effect of solid atoms and dislocation densities. Therefore, the 25 mm plate exhibits the best mechanical properties, with a yield strength of 565.7 MPa along the rolling direction.