Dewen Kong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dewen Kong has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Lingling Wang
College of Civil Engineering, Guizhou University, Guiyang, China
4 shared publications Jing Shu
College of Civil Engineering, Guizhou University, Guiyang, China
3 shared publicationsLingling Wang
College of Civil Engineering, Guizhou University, Guiyang, China
3 shared publications- Gengyin Cui
College of Civil Engineering, Guizhou University, Guiyang, China
2 shared publications Hongfang An
2 shared publicationsNinggui Hu
College of Civil Engineering Guizhou University Guiyang China
2 shared publications
Latest Publications
- 29 October 2025
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 40 (5) , 1349-1362
RSM-based Multi-objective Optimization of Desulfurized Gypsum-based Composites Properties
- 29 October 2025
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 40 (5) , 1349-1362
RSM-based Multi-objective Optimization of Desulfurized Gypsum-based Composites Properties
- 28 October 2025
- Published by Wiley in Structural Concrete
Experimental evaluation on interfacial bond performance between C30 phosphogypsum‐based concrete and steel tubular
Phosphogypsum‐based concrete filled steel tubular (PGBC‐FST) was designed to improve the interface bond property. The experimental and theoretical studies were conducted on the cement‐based concrete filled steel tubular (CBC‐FST) and PGBC‐FST to compare the interfacial bond properties. The bond mechanisms of PGBC‐FST were discussed by experimental F‐S curve, to verify the better bond properties of the PGBC‐FST structure. Moreover, the effects of cement substitution rate, raw phosphogypsum/hemihydrate phosphogypsum (RPG/HPG), and wall thickness of steel tubular on the average bond strength and critical relative slip of PGBC‐FST were discussed using a single‐factor experiment. Simultaneously, the prediction models of average bond strength and critical slip displacement of PGBC‐FST were presented depending on the effects of cement substitution rate, RPG/HPG and steel tubular wall thickness. The results showed that PGBC‐FST had a higher average bond strength than CBC‐FST, and the highest value was 1.149 MPa. The average bond strength of PGBC‐FST increased with the increase of the cement substitution rate of PGBC, increased first and then decreased with the increase of HPG dosage, and decreased with the decrease of steel tubular wall thickness. The bond stress on the outer wall of the PGBC‐FST steel tubular presented a “V” shape distribution below the critical sliding load, and produced stress redistribution after the overall relative slip. The prediction models of average bonding strength and critical relative slip of PGBC‐FST exhibited good accordance with experimental results.
- 28 October 2025
- Published by Wiley in Structural Concrete
Experimental evaluation on interfacial bond performance between C30 phosphogypsum‐based concrete and steel tubular
Phosphogypsum‐based concrete filled steel tubular (PGBC‐FST) was designed to improve the interface bond property. The experimental and theoretical studies were conducted on the cement‐based concrete filled steel tubular (CBC‐FST) and PGBC‐FST to compare the interfacial bond properties. The bond mechanisms of PGBC‐FST were discussed by experimental F‐S curve, to verify the better bond properties of the PGBC‐FST structure. Moreover, the effects of cement substitution rate, raw phosphogypsum/hemihydrate phosphogypsum (RPG/HPG), and wall thickness of steel tubular on the average bond strength and critical relative slip of PGBC‐FST were discussed using a single‐factor experiment. Simultaneously, the prediction models of average bond strength and critical slip displacement of PGBC‐FST were presented depending on the effects of cement substitution rate, RPG/HPG and steel tubular wall thickness. The results showed that PGBC‐FST had a higher average bond strength than CBC‐FST, and the highest value was 1.149 MPa. The average bond strength of PGBC‐FST increased with the increase of the cement substitution rate of PGBC, increased first and then decreased with the increase of HPG dosage, and decreased with the decrease of steel tubular wall thickness. The bond stress on the outer wall of the PGBC‐FST steel tubular presented a “V” shape distribution below the critical sliding load, and produced stress redistribution after the overall relative slip. The prediction models of average bonding strength and critical relative slip of PGBC‐FST exhibited good accordance with experimental results.
- 2 September 2025
- Published by Springer Nature in International Journal of Civil Engineering
- p. 1-16
Seismic Performance and Fracture Modes of New Phosphogypsum-Concrete Combined Wallboard
- 2 September 2025
- Published by Springer Nature in International Journal of Civil Engineering
- p. 1-16
Seismic Performance and Fracture Modes of New Phosphogypsum-Concrete Combined Wallboard
- 24 July 2025
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 40 (4) , 1078-1090
Effect Evaluation and Mechanism Analysis of β-Hemihydrate Phosphogypsum on Performances of Red Mud Concretes
- 24 July 2025
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 40 (4) , 1078-1090
Effect Evaluation and Mechanism Analysis of β-Hemihydrate Phosphogypsum on Performances of Red Mud Concretes
- 13 May 2024
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 26 (4) , 2175-2186
Green-brick preparation method for the resource utilization of sewage sludge and phosphogypsum with a low heavy-metal pollution risk
- 13 May 2024
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 26 (4) , 2175-2186
Green-brick preparation method for the resource utilization of sewage sludge and phosphogypsum with a low heavy-metal pollution risk
- 6 December 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 411
The effects of admixtures on the durability properties of phosphogypsum-based cementitious materials
- 6 December 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 411
The effects of admixtures on the durability properties of phosphogypsum-based cementitious materials
- Open Access
Effects of Different Admixtures on the Mechanical and Thermal Insulation Properties of Desulfurization Gypsum-Based Composites
The single-factor experiments are designed to quantitatively investigate the effects of silica fume, mineral powder, and fly ash on the mechanical and thermal insulation properties of desulfurization gypsum-based composites (DGCs). The effect mechanism is discussed from the microscopic morphology of the internal structure, and the corresponding relationship between the strength and thermal conductivity of this material is evaluated by the regression model. The results show that the admixture of silica fume, mineral powder, and fly ash improves the strengths and thermal insulation properties of DGCs, with the order of influence silica fume > mineral powder > fly ash. The optimal 28 d compressive strength and thermal conductivity are 34.17 MPa and 0.2146 W/(m·K), respectively, at a silica fume dosage of 35%. The enhancement effects on the strength and thermal insulation performance of DGCs are attributed to the increase in the hydration products C-S-H gel and Aft. Moreover, the thermal conductivity linearly decreases with the increase in the compressive strength of DGC after adding silica fume, mineral powder, and fly ash. The linear regression models exhibit good precision for evaluating the corresponding relationships between the compressive strength and thermal conductivity of DGCs with different admixtures.
Open AccessEffects of Different Admixtures on the Mechanical and Thermal Insulation Properties of Desulfurization Gypsum-Based Composites
The single-factor experiments are designed to quantitatively investigate the effects of silica fume, mineral powder, and fly ash on the mechanical and thermal insulation properties of desulfurization gypsum-based composites (DGCs). The effect mechanism is discussed from the microscopic morphology of the internal structure, and the corresponding relationship between the strength and thermal conductivity of this material is evaluated by the regression model. The results show that the admixture of silica fume, mineral powder, and fly ash improves the strengths and thermal insulation properties of DGCs, with the order of influence silica fume > mineral powder > fly ash. The optimal 28 d compressive strength and thermal conductivity are 34.17 MPa and 0.2146 W/(m·K), respectively, at a silica fume dosage of 35%. The enhancement effects on the strength and thermal insulation performance of DGCs are attributed to the increase in the hydration products C-S-H gel and Aft. Moreover, the thermal conductivity linearly decreases with the increase in the compressive strength of DGC after adding silica fume, mineral powder, and fly ash. The linear regression models exhibit good precision for evaluating the corresponding relationships between the compressive strength and thermal conductivity of DGCs with different admixtures.
- 30 May 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 392
Effects of hybrid fibers on properties of desulfurized gypsum-based composite cementitious materials
- 30 May 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 392
Effects of hybrid fibers on properties of desulfurized gypsum-based composite cementitious materials
- Open Access
Performance Study and Multi-Index Synergistic Effect Analysis of Phosphogypsum-Based Composite Cementitious Material
The application of phosphogypsum in building materials can consume waste phosphogypsum and reduce ecological pressure. In this study, building phosphogypsum was used as the base material, and fly ash, lime, cement, and other materials were added to explore the performance of phosphogypsum-based cementitious composite building materials via orthogonal experimental method. Variance analysis and multiple regression analysis were used to summarize the performance variation of these phosphogypsum-based composite cementitious materials. This work demonstrates that the building phosphogypsum content and the water-cement mass ratio are significant factors affecting the thermal conductivity and mechanical properties of these materials scanning electron microscopy (SEM) analysis showed that the mechanical properties and thermal insulation properties of the prepared phosphogypsum-based composite cementitious materials were good in the C-S-H gel system and ettringite formation uniform specimens. Regression analysis showed a significant relationship between the building phosphogypsum content, fly ash content in the supplementary cementitious material, lime content, water-cement mass ratio, compressive strength, and thermal conductivity. The compressive strength and the thermal conductivity were analyzed by the index membership degree. The comprehensive performance of the phosphogypsum-based composite cementitious materials was evaluated, and basic theoretical research into the use of the phosphogypsum-based composite cementitious materials in a building non-load-bearing wall was carried out.
Open AccessPerformance Study and Multi-Index Synergistic Effect Analysis of Phosphogypsum-Based Composite Cementitious Material
The application of phosphogypsum in building materials can consume waste phosphogypsum and reduce ecological pressure. In this study, building phosphogypsum was used as the base material, and fly ash, lime, cement, and other materials were added to explore the performance of phosphogypsum-based cementitious composite building materials via orthogonal experimental method. Variance analysis and multiple regression analysis were used to summarize the performance variation of these phosphogypsum-based composite cementitious materials. This work demonstrates that the building phosphogypsum content and the water-cement mass ratio are significant factors affecting the thermal conductivity and mechanical properties of these materials scanning electron microscopy (SEM) analysis showed that the mechanical properties and thermal insulation properties of the prepared phosphogypsum-based composite cementitious materials were good in the C-S-H gel system and ettringite formation uniform specimens. Regression analysis showed a significant relationship between the building phosphogypsum content, fly ash content in the supplementary cementitious material, lime content, water-cement mass ratio, compressive strength, and thermal conductivity. The compressive strength and the thermal conductivity were analyzed by the index membership degree. The comprehensive performance of the phosphogypsum-based composite cementitious materials was evaluated, and basic theoretical research into the use of the phosphogypsum-based composite cementitious materials in a building non-load-bearing wall was carried out.
- Open Access
- 1 March 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (3) , 035506
Effect of the phosphogypsum calcination time on the compressive mechanical properties of phosphogypsum-based composite cementitious materials
In this study, phosphogypsum-based composite cementitious materials (PGCMs) were prepared by adding fixed proportions of additives to calcined phosphogypsum (PG). Samples with dimensions of 40 × 40 × 80 mm and 150 × 150 × 300 mm were used to study the effect of the PG calcination time on the PGCM compressive strength, stress–strain relationship, and failure mode and its mechanism. The test results indicated that the PGCM compressive strength gradually increased as the calcination time increased. When the PG calcination time was 180 min, the compressive strengths of the smaller and larger samples increased by 3 and 3.6 times, respectively, compared with the strengths at a calcination time of 20 min. The main reason for the strength increase was the formation of ettringite and hydrated calcium sulfate dihydrate in the PGCM gel system. Additionally, the PGCM compressive strength was significantly related to the sample size, and its reduction coefficient was between 0.60 and 0.69 at different PG calcination times. As the PG calcination time increased, the peak stress of the PGCM stress–strain curve and the corresponding axial strain increased gradually; moreover, brittle failure became more evident.
- 1 March 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (3) , 035506
Open AccessEffect of the phosphogypsum calcination time on the compressive mechanical properties of phosphogypsum-based composite cementitious materials
In this study, phosphogypsum-based composite cementitious materials (PGCMs) were prepared by adding fixed proportions of additives to calcined phosphogypsum (PG). Samples with dimensions of 40 × 40 × 80 mm and 150 × 150 × 300 mm were used to study the effect of the PG calcination time on the PGCM compressive strength, stress–strain relationship, and failure mode and its mechanism. The test results indicated that the PGCM compressive strength gradually increased as the calcination time increased. When the PG calcination time was 180 min, the compressive strengths of the smaller and larger samples increased by 3 and 3.6 times, respectively, compared with the strengths at a calcination time of 20 min. The main reason for the strength increase was the formation of ettringite and hydrated calcium sulfate dihydrate in the PGCM gel system. Additionally, the PGCM compressive strength was significantly related to the sample size, and its reduction coefficient was between 0.60 and 0.69 at different PG calcination times. As the PG calcination time increased, the peak stress of the PGCM stress–strain curve and the corresponding axial strain increased gradually; moreover, brittle failure became more evident.