Alona Dzevochko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alona Dzevochko has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Oleksandr Dzevochko
National Technical University “Kharkiv Polytechnic Institute
6 shared publications - Mykhaylo Podustov
Національний технічний університет «Харківський політехнічний інститут
4 shared publications - Alevtyna Pereverzieva
National Technical University “Kharkiv Polytechnic Institute
2 shared publications - Yuriy Dotsenko
Ukrainian State University of Science and Technologies
2 shared publications - Denys Nikolaiev
National Technical University "Kharkiv Polytechnic Institute
1 shared publication - Dmytro Makarenko
National Aerospace University “Kharkiv Aviation Institute
1 shared publication
Latest Publications
- Open Access
- 4 April 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 2 (1(82)) , 19-23
Construction of a kinetic equation of carbon removal for controlling steel melting in the metallurgical system “cupola furnace – small converter”
The object of research in the paper is the process of steelmaking in a small converter, which works in tandem with a cupola furnace. The existing problem is that the control of the process of obtaining steel in an oxygen converter is complicated by the need to determine in real time the current chemical composition of the melt, in particular carbon. This is due to the fact that the rate of carbon removal is too high, as a result of which the process of carbon removal is transient. Therefore, it is too difficult to implement regulation based on feedback on continuous measurement. The presence of the specified problem requires solutions related to the possibilities of developing or improving software control of the process. It is shown that in certain sections of the process within each time section of oxygen purging of the melt in the converter, the kinetic curve has a linear form with a constant coefficient value in front of the inlet mine. But the value of the initial coefficient for each equation that describes the process within its limits changes. This allows to state that in case of a change in the initial condition, the kinetic curves shift relative to each other in parallel. On this basis, a system of equations has been constructed that describes the process of carbon removal in a small oxygen converter that receives liquid iron from a cupola furnace. It has been shown that to use the obtained system of equations, it is necessary to know the initial carbon content in the melt discharged from the cupola furnace, and it depends on the method of oxygen supply to the cupola furnace. Based on the modeling of this process in two variants – using a “sharp blow” and supplying oxygen to the air blown into the tuyeres, a nomogram has been constructed. It allows to determine the initial carbon content for the practical use of the obtained system of equations. Using the obtained system makes it possible to determine the time after which oxygen cutoff should be made. This will allow to decide to implement software control of the melt blowing process in the converter. The presented study will be useful for machine-building enterprises that have foundry shops in their structure, where cast iron is smelted for the manufacture of castings.
- 4 April 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 2 (1(82)) , 19-23
Open AccessConstruction of a kinetic equation of carbon removal for controlling steel melting in the metallurgical system “cupola furnace – small converter”
The object of research in the paper is the process of steelmaking in a small converter, which works in tandem with a cupola furnace. The existing problem is that the control of the process of obtaining steel in an oxygen converter is complicated by the need to determine in real time the current chemical composition of the melt, in particular carbon. This is due to the fact that the rate of carbon removal is too high, as a result of which the process of carbon removal is transient. Therefore, it is too difficult to implement regulation based on feedback on continuous measurement. The presence of the specified problem requires solutions related to the possibilities of developing or improving software control of the process. It is shown that in certain sections of the process within each time section of oxygen purging of the melt in the converter, the kinetic curve has a linear form with a constant coefficient value in front of the inlet mine. But the value of the initial coefficient for each equation that describes the process within its limits changes. This allows to state that in case of a change in the initial condition, the kinetic curves shift relative to each other in parallel. On this basis, a system of equations has been constructed that describes the process of carbon removal in a small oxygen converter that receives liquid iron from a cupola furnace. It has been shown that to use the obtained system of equations, it is necessary to know the initial carbon content in the melt discharged from the cupola furnace, and it depends on the method of oxygen supply to the cupola furnace. Based on the modeling of this process in two variants – using a “sharp blow” and supplying oxygen to the air blown into the tuyeres, a nomogram has been constructed. It allows to determine the initial carbon content for the practical use of the obtained system of equations. Using the obtained system makes it possible to determine the time after which oxygen cutoff should be made. This will allow to decide to implement software control of the melt blowing process in the converter. The presented study will be useful for machine-building enterprises that have foundry shops in their structure, where cast iron is smelted for the manufacture of castings.
- Open Access
- 11 February 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 1 (1(81)) , 29-33
Identification of temperature in cupola furnace based on the construction of the “slag composition – slag viscosity” model
The object of the study in the work is the temperature regime of melting in a cupola. The existing problem is that due to the aggressive high-temperature environment, continuous measurement of the parameters of the internal environment in the working space of the cupola furnace is too difficult. Even with the implementation of such a possibility, errors of the first and second types may occur. This necessitates indirect control of the temperature regime, which could provide a solution to the identification problem – whether the control system is really operating in normal mode and meets the accuracy requirements, or whether there is a parametric failure along the corresponding control circuit. The existence of the specified problem requires solutions related to the definition of criteria for evaluating the temperature regime, by which it would be possible to verify the reliable functioning of the melting control system. A criterion for evaluating the temperature regime of melting by the viscosity of the slag as a function of its composition is proposed, which allows identifying the temperature regime of melting with an accuracy of 96 %. This result is due to the proposed two-stage procedure, in which the first stage is the construction of mathematical models that describe the influence of the slag composition on the viscosity, and the second is the construction of a criterion based on the density distribution of the discriminant function for both temperature regimes. Using the obtained criterion also makes it possible to determine the areas of chemical compositions, by which the temperature regime can also be identified. The relationships between the variables for the identification procedure are presented in the form of a structural diagram. The proposed solutions will allow determining the quality of the functioning of the temperature control loop in the melting control system based on periodic control. The presented study will be useful for machine-building enterprises that have foundries in their structure, where cast iron is smelted for the manufacture of castings.
- 11 February 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 1 (1(81)) , 29-33
Open AccessIdentification of temperature in cupola furnace based on the construction of the “slag composition – slag viscosity” model
The object of the study in the work is the temperature regime of melting in a cupola. The existing problem is that due to the aggressive high-temperature environment, continuous measurement of the parameters of the internal environment in the working space of the cupola furnace is too difficult. Even with the implementation of such a possibility, errors of the first and second types may occur. This necessitates indirect control of the temperature regime, which could provide a solution to the identification problem – whether the control system is really operating in normal mode and meets the accuracy requirements, or whether there is a parametric failure along the corresponding control circuit. The existence of the specified problem requires solutions related to the definition of criteria for evaluating the temperature regime, by which it would be possible to verify the reliable functioning of the melting control system. A criterion for evaluating the temperature regime of melting by the viscosity of the slag as a function of its composition is proposed, which allows identifying the temperature regime of melting with an accuracy of 96 %. This result is due to the proposed two-stage procedure, in which the first stage is the construction of mathematical models that describe the influence of the slag composition on the viscosity, and the second is the construction of a criterion based on the density distribution of the discriminant function for both temperature regimes. Using the obtained criterion also makes it possible to determine the areas of chemical compositions, by which the temperature regime can also be identified. The relationships between the variables for the identification procedure are presented in the form of a structural diagram. The proposed solutions will allow determining the quality of the functioning of the temperature control loop in the melting control system based on periodic control. The presented study will be useful for machine-building enterprises that have foundries in their structure, where cast iron is smelted for the manufacture of castings.
- 6 December 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Integrated Technologies and Energy Saving
- No. 1,p. 41-51
DESIGNING OF A NEW HARDWARE AND TECHNOLOGICAL SCHEME OF THE PROCESS OF ORGANIC SUBSTANCES MIXTURES SULPHING
В статті наведено, що поверхнево-активні речовини на основі вищих спиртів фр. С12 – С14 знаходять основне використання в широкому спектрі засобів особистої гігієни, таких як шампуні, піноутворювачі для ван, зубні пасти, рідина для миття посуду, делікатні засоби для прання білизни. Використання ПАР на основі суміші вищіх спиртів фр. С12 – С14 та моноетаноламидів вищіх жирних кислот кокосової олії дає можливість значно покращити якісні характеристики засобів особистої гігієни. Наведено, що основним елементом апаратно-технологічної схеми процесу сульфатування сумішей органічних речовин є трубчастий плівковий абсорбер. Показано, що для сульфатування двохкомпонентних сумішей органічних речовин на основі вищіх спиртів фр. С12 – С14 та моноетаноламидів вищіх жирних кислот кокосової олії необхідно використовувати трубчастий плівковий абсорбер, який має двоступінчасте охолодження – верхня частина 1/3 довжини абсорбера, нижня частина 2/3 довжини абсорбера. Швидкість газоповітряного потоку підтримується на рівні Vг = 20 м/с, мольне співвідношення реагентів 1,08 : 1,0 концентрація триоксиду сірки в газоповітряному потоці – 3,7 % об., температура вихідних реагентів: рідинної фази – 313 К, газоповітряного потоку – 303 К, охолоджувальної води – 293 К. Виходячи з таких початкових даних був розрахований промисловий трубчастий абсорбер. Наведені дані такого розрахунку. Наведено, що розрахунок промислового трубчастого плівкового абсорбера проводився згідно з розробленим алгоритмом та програмою на мові MatLab, в програмі використано ітераційний метод розрахунку. Наведено розрахунок кількості труб промислового абсорбера. Показано, що абсорбер складається з таких основних елементів – верхньої елептичної кришки, розподільчої плити газоповітряного потоку, камери для розподілу суміші органічних речовин, плівкоутворювачів, двох камер охолодження, нижньої елептичної кришки. Наведено, що на основі промислового трубчастого плівкового абсорбера розроблена та приведена нова апаратурно-технологіна схема.
- 6 December 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Integrated Technologies and Energy Saving
- No. 1,p. 41-51
DESIGNING OF A NEW HARDWARE AND TECHNOLOGICAL SCHEME OF THE PROCESS OF ORGANIC SUBSTANCES MIXTURES SULPHING
В статті наведено, що поверхнево-активні речовини на основі вищих спиртів фр. С12 – С14 знаходять основне використання в широкому спектрі засобів особистої гігієни, таких як шампуні, піноутворювачі для ван, зубні пасти, рідина для миття посуду, делікатні засоби для прання білизни. Використання ПАР на основі суміші вищіх спиртів фр. С12 – С14 та моноетаноламидів вищіх жирних кислот кокосової олії дає можливість значно покращити якісні характеристики засобів особистої гігієни. Наведено, що основним елементом апаратно-технологічної схеми процесу сульфатування сумішей органічних речовин є трубчастий плівковий абсорбер. Показано, що для сульфатування двохкомпонентних сумішей органічних речовин на основі вищіх спиртів фр. С12 – С14 та моноетаноламидів вищіх жирних кислот кокосової олії необхідно використовувати трубчастий плівковий абсорбер, який має двоступінчасте охолодження – верхня частина 1/3 довжини абсорбера, нижня частина 2/3 довжини абсорбера. Швидкість газоповітряного потоку підтримується на рівні Vг = 20 м/с, мольне співвідношення реагентів 1,08 : 1,0 концентрація триоксиду сірки в газоповітряному потоці – 3,7 % об., температура вихідних реагентів: рідинної фази – 313 К, газоповітряного потоку – 303 К, охолоджувальної води – 293 К. Виходячи з таких початкових даних був розрахований промисловий трубчастий абсорбер. Наведені дані такого розрахунку. Наведено, що розрахунок промислового трубчастого плівкового абсорбера проводився згідно з розробленим алгоритмом та програмою на мові MatLab, в програмі використано ітераційний метод розрахунку. Наведено розрахунок кількості труб промислового абсорбера. Показано, що абсорбер складається з таких основних елементів – верхньої елептичної кришки, розподільчої плити газоповітряного потоку, камери для розподілу суміші органічних речовин, плівкоутворювачів, двох камер охолодження, нижньої елептичної кришки. Наведено, що на основі промислового трубчастого плівкового абсорбера розроблена та приведена нова апаратурно-технологіна схема.
- 23 December 2021
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Chemistry, Chemical Technology and Ecology
- No. 2(6),p. 3-8
INVESTIGATION OF THE NEUTRALIZATION PROCESS OF SULFATION PRODUCTS IN THE SURFACTANTS PRODUCTION
The process of sulfation products neutralization in the production of surfactants is not basic, but at this stage the positive effects obtained at the stage of sulfation of organic matter with sulfur trioxide gas are fixed. To preserve the degree of sulfation obtained, it is necessary to carry out the neutralization process under conditions precluding the occurrence of hydrolysis in an acidic medium. The neutralization reaction takes place with a high heat release of about 40 kJ / mol. Analysis of the literature data showed that the neutralization process is not well covered. Little data and hardware and technological design of the process. The process of neutralization in industrial conditions is carried out in apparatus with mechanical turbine mixers, to remove the heat of the exothermic reaction, the paste from the neutralizer is fed into a water-borne heat exchanger and returns to the neutralizer again. The purpose of this study is to determine the optimal technological parameters of the process of neutralization of sulfate products and the development of a mathematical model of this process. The results of experimental studies of the process of sulfation products neutralization with an aqueous solution of sodium hydroxide are presented. During the research, the influence of technological parameters on the quality indicators of neutralization products was determined, the main of which is the degree of sulfation. The optimal technological parameters for carrying out this process in a reactor with a stirrer under laboratory conditions were found. Based on the data obtained in the basis of this process, the use of a continuous-action reactor with a turbine mixer and with a combined heat exchanger. For the transition to an industrial reactor-neutralizer, a mathematical model has been developed, which makes it possible, by means of mathematical modeling, to correct technological parameters in industrial conditions.
- 23 December 2021
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI". Series: Chemistry, Chemical Technology and Ecology
- No. 2(6),p. 3-8
INVESTIGATION OF THE NEUTRALIZATION PROCESS OF SULFATION PRODUCTS IN THE SURFACTANTS PRODUCTION
The process of sulfation products neutralization in the production of surfactants is not basic, but at this stage the positive effects obtained at the stage of sulfation of organic matter with sulfur trioxide gas are fixed. To preserve the degree of sulfation obtained, it is necessary to carry out the neutralization process under conditions precluding the occurrence of hydrolysis in an acidic medium. The neutralization reaction takes place with a high heat release of about 40 kJ / mol. Analysis of the literature data showed that the neutralization process is not well covered. Little data and hardware and technological design of the process. The process of neutralization in industrial conditions is carried out in apparatus with mechanical turbine mixers, to remove the heat of the exothermic reaction, the paste from the neutralizer is fed into a water-borne heat exchanger and returns to the neutralizer again. The purpose of this study is to determine the optimal technological parameters of the process of neutralization of sulfate products and the development of a mathematical model of this process. The results of experimental studies of the process of sulfation products neutralization with an aqueous solution of sodium hydroxide are presented. During the research, the influence of technological parameters on the quality indicators of neutralization products was determined, the main of which is the degree of sulfation. The optimal technological parameters for carrying out this process in a reactor with a stirrer under laboratory conditions were found. Based on the data obtained in the basis of this process, the use of a continuous-action reactor with a turbine mixer and with a combined heat exchanger. For the transition to an industrial reactor-neutralizer, a mathematical model has been developed, which makes it possible, by means of mathematical modeling, to correct technological parameters in industrial conditions.
- Open Access
- 21 December 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (6 (114)) , 15-22
Construction of a mathematical model of the film absorber for sulfating two-component mixtures of organic substances
The processes that occur in film absorbers during the sulfation of two-component mixtures of organic substances are quite complex and require mathematical modeling. This paper reports the construction of a mathematical model that makes it possible to adequately describe the process of sulfation involving gaseous sulfur trioxide in the production of surfactants. Based on the model, it became possible to investigate this process for higher alcohols of fractions С12–С14 and monoethanolamides of higher fatty acids of coconut oil. The data are given on the comparison of mathematical modeling results based on the mathematical model built with known experimental data and results of alternative mathematical modeling for different ratios of the length of the reaction pipe to its diameter (l/d). It is shown that the error in comparing the experimental data was 4.8–9.6 % at l l/d=29; 1.1–8.7 % at l/d=70; 3.9–12.3 % at l/d=144. The error in comparing known results of alternative mathematical modeling was, respectively, 6.3–7.2 %, 0.1–6.5 %, 0–1.0 %. These results were obtained for the molar ratio in the range of 1.0–1.15 and the SO3 concentration in the stream of 4.0–6.0 %. Such findings suggest that the established dependences of the basic parameters for the sulfation process are adequate in terms of the absorber length and its radial direction. Therefore, the mathematical model built does hold within the considered ranges of input variables. Consequently, it could be used in the theoretical study of the process of sulfation of two-component mixtures of organic substances by gaseous sulfur trioxide in a film absorber with a downward flow of phases. The results obtained could be used in practice, in particular in the manufacture of high-quality products for the cosmetic industry.
- 21 December 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (6 (114)) , 15-22
Open AccessConstruction of a mathematical model of the film absorber for sulfating two-component mixtures of organic substances
The processes that occur in film absorbers during the sulfation of two-component mixtures of organic substances are quite complex and require mathematical modeling. This paper reports the construction of a mathematical model that makes it possible to adequately describe the process of sulfation involving gaseous sulfur trioxide in the production of surfactants. Based on the model, it became possible to investigate this process for higher alcohols of fractions С12–С14 and monoethanolamides of higher fatty acids of coconut oil. The data are given on the comparison of mathematical modeling results based on the mathematical model built with known experimental data and results of alternative mathematical modeling for different ratios of the length of the reaction pipe to its diameter (l/d). It is shown that the error in comparing the experimental data was 4.8–9.6 % at l l/d=29; 1.1–8.7 % at l/d=70; 3.9–12.3 % at l/d=144. The error in comparing known results of alternative mathematical modeling was, respectively, 6.3–7.2 %, 0.1–6.5 %, 0–1.0 %. These results were obtained for the molar ratio in the range of 1.0–1.15 and the SO3 concentration in the stream of 4.0–6.0 %. Such findings suggest that the established dependences of the basic parameters for the sulfation process are adequate in terms of the absorber length and its radial direction. Therefore, the mathematical model built does hold within the considered ranges of input variables. Consequently, it could be used in the theoretical study of the process of sulfation of two-component mixtures of organic substances by gaseous sulfur trioxide in a film absorber with a downward flow of phases. The results obtained could be used in practice, in particular in the manufacture of high-quality products for the cosmetic industry.
- Open Access
- 9 November 2021
- Published by National Technical University Kharkiv Polytechnic Institute in Integrated Technologies and Energy Saving
- No. 3,p. 3-16
RESEARCH OF THERMAL AND MASS-EXCHANGE PROCESSES IN GAS-LIQUID FILM ABSORBERS IN SURFACE-ACTIVE TECHNOLOGY
У статті наведено, що поверхнево-активні речовини (ПАР) мають асиметрично побудовану молекулу, яка містить гідрофільну та гідрофобну групи. Основним відділенням виробництва ПАР є процес сульфатування органічної речовини газоподібним триоксидом сірки. Показано, що процес сульфатування в газорідинних плівкових абсорберах складається з таких стадій: процес масообміну триоксиду сірки з газоповітряного потоку до рідинної фази; процес абсорбції триоксиду сірки органічною речовиною з проходженням екзотермічної хімічної реакції; процес теплообміну між рідинною фазою та газоповітряним потоком; процес теплообміну між рідинною фазою та потоком охолоджувальної води. Дослідження теплових і масообмінних процесів на цих стадіях дають можливість обрати необхідні рівняння для розрахунку коефіцієнтів теплопередачі, коефіцієнтів тепловіддачі та коефіцієнта масопередачі. Розрахунок коефіцієнта теплопередачі від рідини до газу рекомендовано проводити за рівнянням коли дифузійні і теплові числа Прандтля близькі до одиниці. Використання класичного рівняння для розрахунку коефіцієнта тепловіддачі від рідинної фази до стінки реакційної труби не дали необхідного результату. Тому було використано рівняння, яке враховує властивості газорідинного потоку в цілому. Розрахунок коефіцієнта тепловіддачі від стінки реакційної труби до охолоджувального потоку води рекомендовано проводити за класичним рівнянням критерію Нуссельта. Наведено дані обробки експериментальних даних по розрахунку густини та динамічної в’язкості реакційної маси за довжиною реактора. Рівняння для розрахунку коефіцієнта масопередачі було отримано аналізом 6-ти рівнянь різних авторів, які займалися процесом сульфатування органічних речовин. Для проведення аналізу було розроблено математичний опис процесу сульфатування в плівковому абсорбері. При розробці математичного опису були складені балансові рівняння масо- і теплообміну для реакційної труби. За результатами математичного моделювання було обрано рівняння, яке включає дотичне напруження на поверхні розділу газ-рідина. Результати математичного моделювання були зіставлені з експериментальними даними Гутьєрреса та результатами математичного моделювання Дабіра. Отримані результати будуть використані при математичному моделюванні процесу сульфатування в плівковому абсорбері.
- 9 November 2021
- Published by National Technical University Kharkiv Polytechnic Institute in Integrated Technologies and Energy Saving
- No. 3,p. 3-16
Open AccessRESEARCH OF THERMAL AND MASS-EXCHANGE PROCESSES IN GAS-LIQUID FILM ABSORBERS IN SURFACE-ACTIVE TECHNOLOGY
У статті наведено, що поверхнево-активні речовини (ПАР) мають асиметрично побудовану молекулу, яка містить гідрофільну та гідрофобну групи. Основним відділенням виробництва ПАР є процес сульфатування органічної речовини газоподібним триоксидом сірки. Показано, що процес сульфатування в газорідинних плівкових абсорберах складається з таких стадій: процес масообміну триоксиду сірки з газоповітряного потоку до рідинної фази; процес абсорбції триоксиду сірки органічною речовиною з проходженням екзотермічної хімічної реакції; процес теплообміну між рідинною фазою та газоповітряним потоком; процес теплообміну між рідинною фазою та потоком охолоджувальної води. Дослідження теплових і масообмінних процесів на цих стадіях дають можливість обрати необхідні рівняння для розрахунку коефіцієнтів теплопередачі, коефіцієнтів тепловіддачі та коефіцієнта масопередачі. Розрахунок коефіцієнта теплопередачі від рідини до газу рекомендовано проводити за рівнянням коли дифузійні і теплові числа Прандтля близькі до одиниці. Використання класичного рівняння для розрахунку коефіцієнта тепловіддачі від рідинної фази до стінки реакційної труби не дали необхідного результату. Тому було використано рівняння, яке враховує властивості газорідинного потоку в цілому. Розрахунок коефіцієнта тепловіддачі від стінки реакційної труби до охолоджувального потоку води рекомендовано проводити за класичним рівнянням критерію Нуссельта. Наведено дані обробки експериментальних даних по розрахунку густини та динамічної в’язкості реакційної маси за довжиною реактора. Рівняння для розрахунку коефіцієнта масопередачі було отримано аналізом 6-ти рівнянь різних авторів, які займалися процесом сульфатування органічних речовин. Для проведення аналізу було розроблено математичний опис процесу сульфатування в плівковому абсорбері. При розробці математичного опису були складені балансові рівняння масо- і теплообміну для реакційної труби. За результатами математичного моделювання було обрано рівняння, яке включає дотичне напруження на поверхні розділу газ-рідина. Результати математичного моделювання були зіставлені з експериментальними даними Гутьєрреса та результатами математичного моделювання Дабіра. Отримані результати будуть використані при математичному моделюванні процесу сульфатування в плівковому абсорбері.