Zhihai Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zhihai Yang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Yuanyuan Dong
Science and Technology on Reactor System Design Technology Laboratory, Nuclear Power Institute of China, Chengdu 610041, China
2 shared publications - Cheng Qian
School of Reliability and Systems Engineering, Beihang University, Beijing 100191, China
1 shared publication - Hao Zheng
Science and Technology on Reactor System Design Technology Laboratory, Nuclear Power Institute of China, Chengdu 610213, China
1 shared publication - Ruixiao Zheng
School of Materials Science and Engineering, Key Laboratory of High-temperature Structural Materials and Coatings Technology (Ministry of Industry and Information Technology), Beihang University, Beijing 100191, China
1 shared publication - Tian Hu
Science and Technology on Reactor System Design Technology Laboratory, Nuclear Power Institute of China, Chengdu 610213, China
1 shared publication - Xu Chen
School of Chemical Engineering & Technology Tianjin University Tianjin China
1 shared publication
Latest Publications
- Open Access
Reliability Analysis of Critical Systems in A Fuel Booster Pump Using Advanced Simulation Techniques
The fuel booster pump is one of the most vulnerable physical assets in an operating engine due to the harsh environmental and operational conditions. However, because of its high structural complexity and extreme operational conditions, the reliability design of the fuel booster pump becomes especially difficult, particularly by means of experiments. Thus, to overcome such a problem, advanced simulation techniques have become adequate solutions for the reliability assessment and analysis of a fuel booster pump at the design stage. In this paper, by considering the effects of the uncertainties of multiple design parameters, fatigue life distributions of the four key components (which are the sealing bolt, spline shaft, graphite ring, and inducer, respectively) in a fuel booster pump were first predicted by PoF-based reliability simulations. Then, through further sensitivity analysis on each key component, the design parameters most sensitive to the component mean fatigue life were detected from a total of 25 candidate parameters. These parameters include the “nominal diameter” and “preload” for the sealing bolt, “major and minor diameters of the small spline” for the spline shaft, “inside diameter” for the graphite ring, and “fuel pressure on the blade front surface” for the inducer, respectively. These sensitivity results were found to be in good agreement with the results from the qualitative cause analysis on each key component.
Open AccessReliability Analysis of Critical Systems in A Fuel Booster Pump Using Advanced Simulation Techniques
The fuel booster pump is one of the most vulnerable physical assets in an operating engine due to the harsh environmental and operational conditions. However, because of its high structural complexity and extreme operational conditions, the reliability design of the fuel booster pump becomes especially difficult, particularly by means of experiments. Thus, to overcome such a problem, advanced simulation techniques have become adequate solutions for the reliability assessment and analysis of a fuel booster pump at the design stage. In this paper, by considering the effects of the uncertainties of multiple design parameters, fatigue life distributions of the four key components (which are the sealing bolt, spline shaft, graphite ring, and inducer, respectively) in a fuel booster pump were first predicted by PoF-based reliability simulations. Then, through further sensitivity analysis on each key component, the design parameters most sensitive to the component mean fatigue life were detected from a total of 25 candidate parameters. These parameters include the “nominal diameter” and “preload” for the sealing bolt, “major and minor diameters of the small spline” for the spline shaft, “inside diameter” for the graphite ring, and “fuel pressure on the blade front surface” for the inducer, respectively. These sensitivity results were found to be in good agreement with the results from the qualitative cause analysis on each key component.
- Open Access
Effect of Annealing Temperature on the Microstructure and Mechanical Properties of High-Pressure Torsion-Produced 316LN Stainless Steel
316LN stainless steel is a prospective structural material for the nuclear and medical instruments industries. Severe plastic deformation (SPD) combined with annealing possesses have been used to create materials with excellent mechanical properties. In the present work, a series of ultrafine-grained (UFG) 316LN steels were produced by high-pressure torsion (HPT) and a subsequent annealing process. The effects of annealing temperature on grain recrystallization and precipitation were investigated. Recrystallized UFG 316LN steels can be achieved after annealing at high temperature. The σ phase generates, at grain boundaries, at an annealing temperature range of 750–850 °C. The dislocations induced by recrystallized grain boundaries and strain-induced nanotwins are beneficial for enhancing ductility. Moreover, microcracks are easy to nucleate at the σ phase and the γ-austenite interface, causing unexpected rapid fractures.
Open AccessEffect of Annealing Temperature on the Microstructure and Mechanical Properties of High-Pressure Torsion-Produced 316LN Stainless Steel
316LN stainless steel is a prospective structural material for the nuclear and medical instruments industries. Severe plastic deformation (SPD) combined with annealing possesses have been used to create materials with excellent mechanical properties. In the present work, a series of ultrafine-grained (UFG) 316LN steels were produced by high-pressure torsion (HPT) and a subsequent annealing process. The effects of annealing temperature on grain recrystallization and precipitation were investigated. Recrystallized UFG 316LN steels can be achieved after annealing at high temperature. The σ phase generates, at grain boundaries, at an annealing temperature range of 750–850 °C. The dislocations induced by recrystallized grain boundaries and strain-induced nanotwins are beneficial for enhancing ductility. Moreover, microcracks are easy to nucleate at the σ phase and the γ-austenite interface, causing unexpected rapid fractures.