Happy Nugroho
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Happy Nugroho has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Aji Ery Burhandenny
Mulawarman University
4 shared publications - Didit Suprihanto
Universitas Mulawarman
3 shared publications - Arif Harjanto
Universitas Mulawarman
2 shared publications - Budi Yannur
Program Studi Teknik Elektro, Universitas Mulawarman
2 shared publications - Restu Mukti Utomo
Program Studi Teknik Elektro, Universitas Mulawarman
2 shared publications Universitas Mulawarman Program Studi Teknik Elektro
2 shared publications
Latest Publications
- Open Access
- 2 November 2026
- Published by Universitas Malikussaleh in International Journal of Engineering, Science and Information Technology
- Vol. 6 (4) , 74-84
Design and Construction of a 72V 20Ah Lithium-Ion BMS-Integrated Electric Vehicle Battery Pack for the Pesut EV.1 Electric Go-Kart
This research aims to design, build, and test a 72 Volt 20 Ah lithium-ion battery pack for the Pesut EV.1 Mahakam Team electric go-kart. The battery pack is designed with a 20S4P configuration using lithium-ion cells, equipped with a Daly 72 Volt 100 Ampere Battery Management System (BMS), and modeled in CAD software. Testing was carried out through three charging and discharging trials to analyze the voltage, current, and temperature parameters during the process. To enable real-time monitoring, visualization, and data logging during go-kart operation, an IoT-based telemetry system was integrated using a microcontroller and dedicated sensors communicating via the MQTT protocol. In addition, thermal simulations were carried out using FEA software. The test results demonstrated stable and consistent battery performance. During the charging process, the voltage gradually increased from 68 V to 84 V with a stable charging current in the range of 5.90 A – 12.37 A, yielding an average absorbed capacity of 21.15 Ah and input energy of 1,612.11 Wh, while the temperature remained between 25.00 °C and 28.50 °C. Meanwhile, during the discharging process, the voltage gradually decreased from 84 V to approximately 68 V, with the discharge current reaching up to 68.7 A and a maximum temperature of 43 °C. However, dynamic discharge capacity calculation using a 30-second logging interval resulted in overestimation errors due to transient current fluctuations, indicating the need for higher sampling frequencies in future evaluations. Simulation results also demonstrated an even temperature distribution and no overheating during operation. The results indicate that the developed battery pack performed reliably under the tested charging and discharging conditions for Pesut EV.1 Electric Go-Kart usage and racing applications.
- 2 November 2026
- Published by Universitas Malikussaleh in International Journal of Engineering, Science and Information Technology
- Vol. 6 (4) , 74-84
Open AccessDesign and Construction of a 72V 20Ah Lithium-Ion BMS-Integrated Electric Vehicle Battery Pack for the Pesut EV.1 Electric Go-Kart
This research aims to design, build, and test a 72 Volt 20 Ah lithium-ion battery pack for the Pesut EV.1 Mahakam Team electric go-kart. The battery pack is designed with a 20S4P configuration using lithium-ion cells, equipped with a Daly 72 Volt 100 Ampere Battery Management System (BMS), and modeled in CAD software. Testing was carried out through three charging and discharging trials to analyze the voltage, current, and temperature parameters during the process. To enable real-time monitoring, visualization, and data logging during go-kart operation, an IoT-based telemetry system was integrated using a microcontroller and dedicated sensors communicating via the MQTT protocol. In addition, thermal simulations were carried out using FEA software. The test results demonstrated stable and consistent battery performance. During the charging process, the voltage gradually increased from 68 V to 84 V with a stable charging current in the range of 5.90 A – 12.37 A, yielding an average absorbed capacity of 21.15 Ah and input energy of 1,612.11 Wh, while the temperature remained between 25.00 °C and 28.50 °C. Meanwhile, during the discharging process, the voltage gradually decreased from 84 V to approximately 68 V, with the discharge current reaching up to 68.7 A and a maximum temperature of 43 °C. However, dynamic discharge capacity calculation using a 30-second logging interval resulted in overestimation errors due to transient current fluctuations, indicating the need for higher sampling frequencies in future evaluations. Simulation results also demonstrated an even temperature distribution and no overheating during operation. The results indicate that the developed battery pack performed reliably under the tested charging and discharging conditions for Pesut EV.1 Electric Go-Kart usage and racing applications.
- Open Access
- 17 January 2026
- Published by Universitas Malikussaleh in International Journal of Engineering, Science and Information Technology
- Vol. 6 (1) , 36-43
Improving TDS Sensor Accuracy in an IoT-Based Fertigation Prototype Using Polynomial Regression Calibration and Interpolation
Accurate measurement of Total Dissolved Solids (TDS) is a critical requirement for hydroponic nutrient management, especially in automated fertigation systems that adjust nutrient concentrations based on plant age. However, non-industrial TDS sensors often exhibit significant fluctuations and non-linear errors, leading to unreliable nutrient dosing. This study proposes a calibration approach using second-order polynomial regression combined with interpolation to improve the accuracy of TDS measurements in an IoT-based fertigation prototype for lettuce hydroponics. The calibration was performed using reference TDS solutions and a digital TDS meter to ensure accurate measurements. The results show that the Mean Absolute Percentage Error (MAPE) decreased from 24.771% to 7.5768% during calibration, demonstrating a significant improvement in measurement accuracy. The calibrated sensor readings fall within the acceptable range for hydroponic nutrient control (±10%). This method provides a low-cost, reliable alternative for improving sensor accuracy in IoT fertigation systems.
- 17 January 2026
- Published by Universitas Malikussaleh in International Journal of Engineering, Science and Information Technology
- Vol. 6 (1) , 36-43
Open AccessImproving TDS Sensor Accuracy in an IoT-Based Fertigation Prototype Using Polynomial Regression Calibration and Interpolation
Accurate measurement of Total Dissolved Solids (TDS) is a critical requirement for hydroponic nutrient management, especially in automated fertigation systems that adjust nutrient concentrations based on plant age. However, non-industrial TDS sensors often exhibit significant fluctuations and non-linear errors, leading to unreliable nutrient dosing. This study proposes a calibration approach using second-order polynomial regression combined with interpolation to improve the accuracy of TDS measurements in an IoT-based fertigation prototype for lettuce hydroponics. The calibration was performed using reference TDS solutions and a digital TDS meter to ensure accurate measurements. The results show that the Mean Absolute Percentage Error (MAPE) decreased from 24.771% to 7.5768% during calibration, demonstrating a significant improvement in measurement accuracy. The calibrated sensor readings fall within the acceptable range for hydroponic nutrient control (±10%). This method provides a low-cost, reliable alternative for improving sensor accuracy in IoT fertigation systems.
- Open Access
- 6 June 2025
- Published by Atlantis Press SARL
- p. 25-36
Prototype Design and Implementation of Water Distribution Pipeline Leak Detection based on the Internet of Things (IoT)
- 6 June 2025
- Published by Atlantis Press SARL
- p. 25-36
Open AccessPrototype Design and Implementation of Water Distribution Pipeline Leak Detection based on the Internet of Things (IoT)
- Open Access
- 6 June 2025
- Published by Atlantis Press SARL
- p. 108-126
Automatic Temperature, Lighting, and Fish Feeder Control and Monitoring Systems in Aquascape based on the Internet of Things
- 6 June 2025
- Published by Atlantis Press SARL
- p. 108-126
Open AccessAutomatic Temperature, Lighting, and Fish Feeder Control and Monitoring Systems in Aquascape based on the Internet of Things
- Open Access
- 20 December 2021
- Published by Universitas Hamzanwadi in EDUMATIC: Jurnal Pendidikan Informatika
- Vol. 5 (2) , 352-361
Prototype System Water Level Reservoir untuk Pengendalian Kelebihan Air dengan Mikrokontroller Arduino Uno R3
PDAM Loa Kulu Branch still uses sticks or poles as an indicator of the water level in the reservoir. Reservoir is a place to store clean water production from PDAM, the weakness of using sticks or poles is when the operator does not monitor continuously causing air loss when production becomes large. The goal of the study was to design a water-level prototype to control excess water in the reservoir. The method used is a prototype with the stage of gathering information through interviewing PDAM staff, creating and repairing prototypes and testing prototypes. The test used hardware consisting of Arduino uno r3, ultrasonic sensor hc-sr04, flowmeter sensor yf-s201, 16 x 2 lcd, relay module, buzzer, solenoid valve 12 V_dc, pump 12 V_dc and display measurement results in the visual studio application 2019. Our findings are that the length of reservoir charging with an average input discharge of 3.6 liters / minute is 2.93 minutes. As for the length of emptying the reservoir with an average output discharge of 1.06 liters / minute is 12.10 minutes. The conclusion of this study is that the system can monitor the water level inside the reservoir automatically and know the time needed for the feeling and emptying process of the reservoir.
- 20 December 2021
- Published by Universitas Hamzanwadi in EDUMATIC: Jurnal Pendidikan Informatika
- Vol. 5 (2) , 352-361
Open AccessPrototype System Water Level Reservoir untuk Pengendalian Kelebihan Air dengan Mikrokontroller Arduino Uno R3
PDAM Loa Kulu Branch still uses sticks or poles as an indicator of the water level in the reservoir. Reservoir is a place to store clean water production from PDAM, the weakness of using sticks or poles is when the operator does not monitor continuously causing air loss when production becomes large. The goal of the study was to design a water-level prototype to control excess water in the reservoir. The method used is a prototype with the stage of gathering information through interviewing PDAM staff, creating and repairing prototypes and testing prototypes. The test used hardware consisting of Arduino uno r3, ultrasonic sensor hc-sr04, flowmeter sensor yf-s201, 16 x 2 lcd, relay module, buzzer, solenoid valve 12 V_dc, pump 12 V_dc and display measurement results in the visual studio application 2019. Our findings are that the length of reservoir charging with an average input discharge of 3.6 liters / minute is 2.93 minutes. As for the length of emptying the reservoir with an average output discharge of 1.06 liters / minute is 12.10 minutes. The conclusion of this study is that the system can monitor the water level inside the reservoir automatically and know the time needed for the feeling and emptying process of the reservoir.
- Open Access
- 20 December 2021
- Published by Universitas Hamzanwadi in EDUMATIC: Jurnal Pendidikan Informatika
- Vol. 5 (2) , 352-361
Prototype System Water Level Reservoir untuk Pengendalian Kelebihan Air dengan Mikrokontroller Arduino Uno R3
PDAM Loa Kulu Branch still uses sticks or poles as an indicator of the water level in the reservoir. Reservoir is a place to store clean water production from PDAM, the weakness of using sticks or poles is when the operator does not monitor continuously causing air loss when production becomes large. The goal of the study was to design a water-level prototype to control excess water in the reservoir. The method used is a prototype with the stage of gathering information through interviewing PDAM staff, creating and repairing prototypes and testing prototypes. The test used hardware consisting of Arduino uno r3, ultrasonic sensor hc-sr04, flowmeter sensor yf-s201, 16 x 2 lcd, relay module, buzzer, solenoid valve 12 V_dc, pump 12 V_dc and display measurement results in the visual studio application 2019. Our findings are that the length of reservoir charging with an average input discharge of 3.6 liters / minute is 2.93 minutes. As for the length of emptying the reservoir with an average output discharge of 1.06 liters / minute is 12.10 minutes. The conclusion of this study is that the system can monitor the water level inside the reservoir automatically and know the time needed for the feeling and emptying process of the reservoir.
- 20 December 2021
- Published by Universitas Hamzanwadi in EDUMATIC: Jurnal Pendidikan Informatika
- Vol. 5 (2) , 352-361
Open AccessPrototype System Water Level Reservoir untuk Pengendalian Kelebihan Air dengan Mikrokontroller Arduino Uno R3
PDAM Loa Kulu Branch still uses sticks or poles as an indicator of the water level in the reservoir. Reservoir is a place to store clean water production from PDAM, the weakness of using sticks or poles is when the operator does not monitor continuously causing air loss when production becomes large. The goal of the study was to design a water-level prototype to control excess water in the reservoir. The method used is a prototype with the stage of gathering information through interviewing PDAM staff, creating and repairing prototypes and testing prototypes. The test used hardware consisting of Arduino uno r3, ultrasonic sensor hc-sr04, flowmeter sensor yf-s201, 16 x 2 lcd, relay module, buzzer, solenoid valve 12 V_dc, pump 12 V_dc and display measurement results in the visual studio application 2019. Our findings are that the length of reservoir charging with an average input discharge of 3.6 liters / minute is 2.93 minutes. As for the length of emptying the reservoir with an average output discharge of 1.06 liters / minute is 12.10 minutes. The conclusion of this study is that the system can monitor the water level inside the reservoir automatically and know the time needed for the feeling and emptying process of the reservoir.