Xinfang Ma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xinfang Ma has a total of 170 co-authors. Here are the top co-authors by number of shared publications:
- Shicheng Zhang
State Key Laboratory of Petroleum Resources and Engineering, China University of Petroleum (Beijing), Beijing 102249, China
8 shared publications - Jianye Mou
College of Petroleum Engineering, China University of Petroleum (Beijing), Beijing 102249, China
6 shared publications - Qing Wang
School of Petroleum Engineering, China University of Petroleum (Beijing), Beijing 102249, China
5 shared publications Shicheng Zhang
School of Petroleum Engineering, China University of Petroleum, Beijing, China
5 shared publications- Yipeng Wang
School of Petroleum Engineering, China University of Petroleum (Beijing), Beijing 102249, China
5 shared publications - He Ma
College of Petroleum Engineering, China University of Petroleum, Beijing 102249, China
4 shared publications
Latest Publications
- Open Access
Optimization of Hydraulic Fracturing Parameters and Evolution of the In Situ Stress Field During Waterflooding: A Case Study of the Lower Karamay Formation Reservoir in the Bai 21 Well Block
This research investigates strategies for improving oil recovery from the highly heterogeneous conglomerate deposits of the Lower Karamay Formation in the Bai 21 Well Block of the Junggar Basin. Particular attention is given to the coordinated application of hydraulic fracturing and waterflooding to enhance the effectiveness of infill well development. An integrated approach combining geomechanical modeling, numerical hydraulic-fracturing simulation, and reservoir performance analysis was employed to systematically investigate the effects of proppant ratio, temporary plugging, and proppant placement intensity on fracture propagation, waterflood response, and stress-field evolution. The results show that a proppant ratio of 0.15 and a proppant placement intensity of 2.5 m3/m, combined with temporary plugging and diversion fracturing, can generate short and wide fractures with half-lengths of 40–45 m, effectively mitigating early water channeling and reducing interwell interference. In situ, stress-field simulations further indicate that the stress field evolves non-uniformly during injection and production. The average formation stress initially decreases and subsequently increases, with a maximum reduction of 13.7% relative to the initial value. As waterflooding progresses, the stress gradually recovers, resulting in a final reduction of 10.7%. These findings provide an important reference for the coordinated design of infill-well hydraulic fracturing and waterflooding development in similarly highly heterogeneous conglomerate reservoirs.
Open AccessOptimization of Hydraulic Fracturing Parameters and Evolution of the In Situ Stress Field During Waterflooding: A Case Study of the Lower Karamay Formation Reservoir in the Bai 21 Well Block
This research investigates strategies for improving oil recovery from the highly heterogeneous conglomerate deposits of the Lower Karamay Formation in the Bai 21 Well Block of the Junggar Basin. Particular attention is given to the coordinated application of hydraulic fracturing and waterflooding to enhance the effectiveness of infill well development. An integrated approach combining geomechanical modeling, numerical hydraulic-fracturing simulation, and reservoir performance analysis was employed to systematically investigate the effects of proppant ratio, temporary plugging, and proppant placement intensity on fracture propagation, waterflood response, and stress-field evolution. The results show that a proppant ratio of 0.15 and a proppant placement intensity of 2.5 m3/m, combined with temporary plugging and diversion fracturing, can generate short and wide fractures with half-lengths of 40–45 m, effectively mitigating early water channeling and reducing interwell interference. In situ, stress-field simulations further indicate that the stress field evolves non-uniformly during injection and production. The average formation stress initially decreases and subsequently increases, with a maximum reduction of 13.7% relative to the initial value. As waterflooding progresses, the stress gradually recovers, resulting in a final reduction of 10.7%. These findings provide an important reference for the coordinated design of infill-well hydraulic fracturing and waterflooding development in similarly highly heterogeneous conglomerate reservoirs.
- Open Access
- 17 September 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (18) , 9236
Fracture Initiation and Propagation of Multiple Hydraulic Fractures Across Bedding Planes in Shale Oil Horizontal Well
The Jimsar shale reservoir is characterized by low porosity and low permeability. Multistage fracturing of horizontal wells is an effective development method. However, interference between multiple fractures and the presence of well-developed bedding planes limit the effective extension of fractures. To elucidate the initiation and propagation mechanisms of inter-bed fractures in horizontal multi-stage fracturing within shale reservoirs, this study focuses on the Jimusar Shale outcrop and employs large-scale true triaxial hydraulic fracturing physical simulation experiments to construct an experimental model of horizontal multi-stage fracturing. By analyzing fracture morphology, propagation paths, and bedding plane activation characteristics, the study elucidates the fracture propagation patterns under various conditions. Results indicate the following: (1) Increasing the fluid injection rate enhances the net pressure at the fracture tip, effectively overcoming the resistance of bedding planes and promoting the continued propagation of hydraulic fractures across bedding interfaces. (2) Stage spacing affects the coordinated propagation of hydraulic fractures by modifying the stress shadow effect between adjacent fractures. A smaller stage spacing intensifies stress interference, leading to the suppression of local fracture propagation and an increased likelihood of fracture communication. (3) The horizontal stress difference is the primary controlling factor governing fracture propagation direction and bedding penetration capability. A larger horizontal stress difference promotes stable fracture propagation along the direction of the maximum horizontal principal stress and facilitates penetration through bedding planes, whereas a lower horizontal stress difference favors bedding plane activation and fracture deflection, resulting in the formation of a more complex fracture network. The study has established an understanding of the fracture expansion laws under different parameter conditions, which can provide theoretical basis and technical support for the optimization design of multi-stage fracturing parameters in horizontal shale oil wells and the efficient modification of reservoirs.
- 17 September 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (18) , 9236
Open AccessFracture Initiation and Propagation of Multiple Hydraulic Fractures Across Bedding Planes in Shale Oil Horizontal Well
The Jimsar shale reservoir is characterized by low porosity and low permeability. Multistage fracturing of horizontal wells is an effective development method. However, interference between multiple fractures and the presence of well-developed bedding planes limit the effective extension of fractures. To elucidate the initiation and propagation mechanisms of inter-bed fractures in horizontal multi-stage fracturing within shale reservoirs, this study focuses on the Jimusar Shale outcrop and employs large-scale true triaxial hydraulic fracturing physical simulation experiments to construct an experimental model of horizontal multi-stage fracturing. By analyzing fracture morphology, propagation paths, and bedding plane activation characteristics, the study elucidates the fracture propagation patterns under various conditions. Results indicate the following: (1) Increasing the fluid injection rate enhances the net pressure at the fracture tip, effectively overcoming the resistance of bedding planes and promoting the continued propagation of hydraulic fractures across bedding interfaces. (2) Stage spacing affects the coordinated propagation of hydraulic fractures by modifying the stress shadow effect between adjacent fractures. A smaller stage spacing intensifies stress interference, leading to the suppression of local fracture propagation and an increased likelihood of fracture communication. (3) The horizontal stress difference is the primary controlling factor governing fracture propagation direction and bedding penetration capability. A larger horizontal stress difference promotes stable fracture propagation along the direction of the maximum horizontal principal stress and facilitates penetration through bedding planes, whereas a lower horizontal stress difference favors bedding plane activation and fracture deflection, resulting in the formation of a more complex fracture network. The study has established an understanding of the fracture expansion laws under different parameter conditions, which can provide theoretical basis and technical support for the optimization design of multi-stage fracturing parameters in horizontal shale oil wells and the efficient modification of reservoirs.
- Open Access
Lithology-Dependent Fracture Propagation in Ultra-Large True-Triaxial Hydraulic-Fracturing Experiments
Tight reservoirs commonly exhibit low permeability and pronounced lithological heterogeneity, resulting in complex interactions among far-field stress, local structural weakness, and fluid-driven fracture propagation. In this study, four non-replicated 2 m × 2 m × 1 m physical-model specimens representing tight glutenite, tight sandstone, and No. 3 coal rock from the Huabei Oilfield were investigated using an ultra-large true-triaxial hydraulic-fracturing system. Surface-fracture observations, microseismic monitoring, and high-frequency wellhead-pressure measurements were integrated to compare fracture responses under lithology-specific combinations of injection rate, fluid viscosity, perforation configuration, and stress state. The tested glutenite cases exhibited branched or localized fracture patterns depending on the combined treatment configuration; the sandstone case was dominated by a throughgoing main fracture approximately aligned with the principal-stress direction; and the coal-rock case showed extensive participation of bedding and cleat systems. These morphological differences were accompanied by distinct pressure and microseismic signatures, indicating different pathways of hydraulic-energy redistribution and fracture activation. For the two glutenite cases, the combined change from a single-perforation configuration at 0.5 m3/min to three helical perforations at 120° and 0.7 m3/min was associated with a 42.2% larger microseismic-derived stimulated reservoir volume (SRV). Taken together, these responses indicate a shift from stronger far-field-stress-controlled localization in the comparatively uniform sandstone to progressively greater local structural control by heterogeneous interfaces in glutenite and by bedding/cleat discontinuities in coal rock. Because each configuration was represented by a single specimen and several experimental variables changed simultaneously among cases, the observed differences are interpreted as case-specific mechanistic trends rather than statistically established universal relationships. The results show the value of combining fracture morphology, microseismic spatial evolution, and pressure dynamics for interpreting lithology-dependent fracture propagation in ultra-large physical models and for developing qualitative, lithology-adapted hydraulic-fracturing concepts.
Open AccessLithology-Dependent Fracture Propagation in Ultra-Large True-Triaxial Hydraulic-Fracturing Experiments
Tight reservoirs commonly exhibit low permeability and pronounced lithological heterogeneity, resulting in complex interactions among far-field stress, local structural weakness, and fluid-driven fracture propagation. In this study, four non-replicated 2 m × 2 m × 1 m physical-model specimens representing tight glutenite, tight sandstone, and No. 3 coal rock from the Huabei Oilfield were investigated using an ultra-large true-triaxial hydraulic-fracturing system. Surface-fracture observations, microseismic monitoring, and high-frequency wellhead-pressure measurements were integrated to compare fracture responses under lithology-specific combinations of injection rate, fluid viscosity, perforation configuration, and stress state. The tested glutenite cases exhibited branched or localized fracture patterns depending on the combined treatment configuration; the sandstone case was dominated by a throughgoing main fracture approximately aligned with the principal-stress direction; and the coal-rock case showed extensive participation of bedding and cleat systems. These morphological differences were accompanied by distinct pressure and microseismic signatures, indicating different pathways of hydraulic-energy redistribution and fracture activation. For the two glutenite cases, the combined change from a single-perforation configuration at 0.5 m3/min to three helical perforations at 120° and 0.7 m3/min was associated with a 42.2% larger microseismic-derived stimulated reservoir volume (SRV). Taken together, these responses indicate a shift from stronger far-field-stress-controlled localization in the comparatively uniform sandstone to progressively greater local structural control by heterogeneous interfaces in glutenite and by bedding/cleat discontinuities in coal rock. Because each configuration was represented by a single specimen and several experimental variables changed simultaneously among cases, the observed differences are interpreted as case-specific mechanistic trends rather than statistically established universal relationships. The results show the value of combining fracture morphology, microseismic spatial evolution, and pressure dynamics for interpreting lithology-dependent fracture propagation in ultra-large physical models and for developing qualitative, lithology-adapted hydraulic-fracturing concepts.
- Open Access
- 8 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (8) , 3625
Numerical Simulation of Multi-Field Evolution in Fractured Production of Horizontal Shale Oil Wells in Jimusar
The Jimusar shale reservoir exhibits extremely low permeability, classified as an ultra-low porosity and ultra-low permeability formation. Crude oil mobility is poor, and the reservoir demonstrates significant heterogeneity. Conventional horizontal well fracturing development fails to meet requirements, facing issues such as pronounced energy depletion in the formation, unclear oil–water distribution, and changes in formation stress direction. Based on the reservoir properties of the Jimusar shale oil reservoir, this paper establishes a fracture propagation model for horizontal wellbore hydraulic fracturing and a reservoir numerical model. It simulates the evolution of pressure fields, stress fields, and seepage fields at different time points during the fracturing and production phases of horizontal wells. Results indicate the following: (1) When fracturing fluid is injected into the formation, oil saturation around fractures rapidly decreases. During the initial production phase, oil saturation around fractures increases due to the recovery of some fracturing fluid and the sorption effect between fracturing fluid and crude oil. (2) Formation pressure around horizontal wells significantly increases upon fracturing fluid injection. The dual effects of fracture opening and fluid injection cause stress to rise near fractures. During production, both formation pressure and stress decrease near the wellbore, with greater pressure reduction in the near-wellbore zone than in the far-wellbore zone. However, formation stress decreases less near the wellbore due to stress concentration effects from fracture opening, resulting in a smaller reduction than in the far-wellbore zone. (3) The formation surrounding the fracture undergoes dual influences from fracture opening and fracturing fluid injection, causing deflection in the direction of near-wellbore stress. During the initial production phase, the impact of stress deflection gradually diminishes with ongoing production. However, after prolonged production, the deflection of formation stress intensifies. The conclusion states that this understanding clarifies the multi-field evolution patterns in fracturing production for horizontal well clusters, providing theoretical guidance for subsequent shale development processes.
- 8 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (8) , 3625
Open AccessNumerical Simulation of Multi-Field Evolution in Fractured Production of Horizontal Shale Oil Wells in Jimusar
The Jimusar shale reservoir exhibits extremely low permeability, classified as an ultra-low porosity and ultra-low permeability formation. Crude oil mobility is poor, and the reservoir demonstrates significant heterogeneity. Conventional horizontal well fracturing development fails to meet requirements, facing issues such as pronounced energy depletion in the formation, unclear oil–water distribution, and changes in formation stress direction. Based on the reservoir properties of the Jimusar shale oil reservoir, this paper establishes a fracture propagation model for horizontal wellbore hydraulic fracturing and a reservoir numerical model. It simulates the evolution of pressure fields, stress fields, and seepage fields at different time points during the fracturing and production phases of horizontal wells. Results indicate the following: (1) When fracturing fluid is injected into the formation, oil saturation around fractures rapidly decreases. During the initial production phase, oil saturation around fractures increases due to the recovery of some fracturing fluid and the sorption effect between fracturing fluid and crude oil. (2) Formation pressure around horizontal wells significantly increases upon fracturing fluid injection. The dual effects of fracture opening and fluid injection cause stress to rise near fractures. During production, both formation pressure and stress decrease near the wellbore, with greater pressure reduction in the near-wellbore zone than in the far-wellbore zone. However, formation stress decreases less near the wellbore due to stress concentration effects from fracture opening, resulting in a smaller reduction than in the far-wellbore zone. (3) The formation surrounding the fracture undergoes dual influences from fracture opening and fracturing fluid injection, causing deflection in the direction of near-wellbore stress. During the initial production phase, the impact of stress deflection gradually diminishes with ongoing production. However, after prolonged production, the deflection of formation stress intensifies. The conclusion states that this understanding clarifies the multi-field evolution patterns in fracturing production for horizontal well clusters, providing theoretical guidance for subsequent shale development processes.
- Open Access
Experimental Study on Layerwise Expansion of Hydraulic Fractures in Tight Sandstone Reservoirs Controlled by Fractures
The bottom water of the Shizhouji Formation tight sandstone reservoir in the Tazhong Shun 9 well area is developed. General fracturing faces the problem of excessive extension of hydraulic fractures and easy communication with water layers. A true triaxial fracturing physical simulation experiment was conducted on the sandstone and mudstone outcrops of the same layer to explore the expansion laws of hydraulic fractures in the tight sandstone reservoir and consider the influence of mudstone interlayers, horizontal stress difference, fracturing fluid flow rate, and viscosity. The mechanism of multi-cluster fractures/artificial fractures penetrating through the layers was revealed. The research results show that the existence of mudstone interlayers greatly increases the complexity of fractures, from 1.88 to 2.96, an increase of 57%. When there is a mudstone interlayer in the rock, the fracturing process is prone to open weak planes, hindering the expansion of hydraulic fractures. The hydraulic fractures of Sample No. 4 were cut off four times and penetrated through the layers once. The larger the flow rate, the greater the complexity of hydraulic fractures, and the easier the fractures penetrate through the layers. The fractures with a large flow rate (200 mL/min) were cut off three times, and the stress difference was larger, the hydraulic fractures tended to be simple, and the penetration through the layers was zero times at a high-level stress difference (18 MPa); the greater the viscosity, the greater the fracture pressure, and the complexity of fractures first increased and then decreased; the greater the viscosity, the more easily the hydraulic fractures penetrate through the layers, with low viscosity cutting off three times, medium viscosity cutting off four times, and high viscosity cutting off five times. Therefore, considering the limitation requirements of the on-site fracturing on the extension of fracture height, it is recommended that the on-site fracturing construction flow rate be 6 m3/min, and the fracturing fluid viscosity be 10 mPa·s.
Open AccessExperimental Study on Layerwise Expansion of Hydraulic Fractures in Tight Sandstone Reservoirs Controlled by Fractures
The bottom water of the Shizhouji Formation tight sandstone reservoir in the Tazhong Shun 9 well area is developed. General fracturing faces the problem of excessive extension of hydraulic fractures and easy communication with water layers. A true triaxial fracturing physical simulation experiment was conducted on the sandstone and mudstone outcrops of the same layer to explore the expansion laws of hydraulic fractures in the tight sandstone reservoir and consider the influence of mudstone interlayers, horizontal stress difference, fracturing fluid flow rate, and viscosity. The mechanism of multi-cluster fractures/artificial fractures penetrating through the layers was revealed. The research results show that the existence of mudstone interlayers greatly increases the complexity of fractures, from 1.88 to 2.96, an increase of 57%. When there is a mudstone interlayer in the rock, the fracturing process is prone to open weak planes, hindering the expansion of hydraulic fractures. The hydraulic fractures of Sample No. 4 were cut off four times and penetrated through the layers once. The larger the flow rate, the greater the complexity of hydraulic fractures, and the easier the fractures penetrate through the layers. The fractures with a large flow rate (200 mL/min) were cut off three times, and the stress difference was larger, the hydraulic fractures tended to be simple, and the penetration through the layers was zero times at a high-level stress difference (18 MPa); the greater the viscosity, the greater the fracture pressure, and the complexity of fractures first increased and then decreased; the greater the viscosity, the more easily the hydraulic fractures penetrate through the layers, with low viscosity cutting off three times, medium viscosity cutting off four times, and high viscosity cutting off five times. Therefore, considering the limitation requirements of the on-site fracturing on the extension of fracture height, it is recommended that the on-site fracturing construction flow rate be 6 m3/min, and the fracturing fluid viscosity be 10 mPa·s.
- Open Access
Research on High-Pressure Energy Injection and Response Mechanism in Tight Sandstone Reservoirs
To reveal the energy transfer mechanism of water injection and the dynamic response characteristics of pore pressure in tight sandstone reservoirs, and to clarify the influence of lithology, injection pressure, and injection method on the energy enhancement effect of water injection, a high-pressure energy injection and response testing system and nuclear magnetic resonance (NMR) testing technology were used to conduct systematic water injection energy enhancement experiments on three rock types: mudstone, sandstone, and naturally fractured sandstone. Combined with pressure dynamic monitoring and pore structure evolution analysis, the pressure response characteristics and energy enhancement mechanism of rock samples under different experimental conditions were explored. The experimental results showed that the NMR T2 distribution of the three rock samples exhibited bimodal characteristics, corresponding to small pores (pore size < 1000 nm) and large pores/microcracks (pore size > 1000 nm), respectively. There were significant lithological differences in the evolution of pore structure during water injection, with a cumulative decrease of 7.2% in the proportion of large pores in mudstone and an increase of 9.3% in the proportion of large pores in sandstone with natural fracture development. There is a positive correlation between injection pressure and the energy enhancement effect. Under an injection pressure of 40 MPa, the pressure increment at the outlet end of sandstone with natural fracture development reaches 8.06 MPa, and the energy enhancement effect is 24% higher than that under the 30 MPa working condition, while the mudstone only increases by 15%. The energy enhancement effect of intermittent water injection is significantly better than that of depleted water injection, and the energy enhancement effects of the three rock samples are increased by 18.6%, 12.0%, and 6.9%, respectively. Overall, sandstone with natural fractures has the best energy enhancement effect, followed by sandstone, and mudstone has the worst. The connectivity of pores and the degree of fracture development are the core factors that dominate the water injection energy enhancement effect and pressure transmission efficiency. The research results can provide reliable experimental basis and theoretical support for optimizing water injection development plans, improving energy efficiency, and dynamically regulating stress fields in tight sandstone reservoirs.
Open AccessResearch on High-Pressure Energy Injection and Response Mechanism in Tight Sandstone Reservoirs
To reveal the energy transfer mechanism of water injection and the dynamic response characteristics of pore pressure in tight sandstone reservoirs, and to clarify the influence of lithology, injection pressure, and injection method on the energy enhancement effect of water injection, a high-pressure energy injection and response testing system and nuclear magnetic resonance (NMR) testing technology were used to conduct systematic water injection energy enhancement experiments on three rock types: mudstone, sandstone, and naturally fractured sandstone. Combined with pressure dynamic monitoring and pore structure evolution analysis, the pressure response characteristics and energy enhancement mechanism of rock samples under different experimental conditions were explored. The experimental results showed that the NMR T2 distribution of the three rock samples exhibited bimodal characteristics, corresponding to small pores (pore size < 1000 nm) and large pores/microcracks (pore size > 1000 nm), respectively. There were significant lithological differences in the evolution of pore structure during water injection, with a cumulative decrease of 7.2% in the proportion of large pores in mudstone and an increase of 9.3% in the proportion of large pores in sandstone with natural fracture development. There is a positive correlation between injection pressure and the energy enhancement effect. Under an injection pressure of 40 MPa, the pressure increment at the outlet end of sandstone with natural fracture development reaches 8.06 MPa, and the energy enhancement effect is 24% higher than that under the 30 MPa working condition, while the mudstone only increases by 15%. The energy enhancement effect of intermittent water injection is significantly better than that of depleted water injection, and the energy enhancement effects of the three rock samples are increased by 18.6%, 12.0%, and 6.9%, respectively. Overall, sandstone with natural fractures has the best energy enhancement effect, followed by sandstone, and mudstone has the worst. The connectivity of pores and the degree of fracture development are the core factors that dominate the water injection energy enhancement effect and pressure transmission efficiency. The research results can provide reliable experimental basis and theoretical support for optimizing water injection development plans, improving energy efficiency, and dynamically regulating stress fields in tight sandstone reservoirs.
- Open Access
Study on Microscopic Pore Structure and Mechanical Characteristics of Tight Sandstone Under Hydration Effect
During the energy storage fracturing process of tight sandstone reservoirs, the pre-injection of fracturing fluid is used to supplement the formation energy, and the physical properties of rocks change under hydration. To reveal the damage mechanism of hydration on tight sandstone, the tight sandstone surrounding the Daqing Changyuan in the northern part of the Songliao Basin was taken as the research object. Through indoor static hydration experiments, combined with scanning electron microscopy (SEM), nuclear magnetic resonance (NMR), Nano-indentation experiments, and other methods, the evolution laws of rock micro-pore morphology, microfracture parameters, Young’s modulus, hardness, and other mechanical indicators under different hydration durations and soaking pressures were systematically explored. The research results show that the water–rock interaction of acidic slick water fracturing fluid significantly changes the mineral composition and microstructure of mudstone and sandstone, controls the development of induced fractures, and degrades the micro-mechanical properties of rocks, with significant lithological differences. In terms of mineral evolution, the soaking time causes the clay minerals in mudstone to increase by up to 12.0%, while pressure causes the carbonate minerals in sandstone to decrease by up to 23.3%. In terms of induced fracture development, the induced fracture widths of sandstone and mudstone under 30 MPa of pressure increase by 122.4% and 85.7%, respectively. The fracture width of mudstone shows a trend of “increasing first and then decreasing” with time, while that of sandstone decreases monotonically. In terms of micro-mechanical properties, after soaking for 168 h, the Young’s modulus of mudstone decreases by up to 66.9%, much higher than that of sandstone (29.5%), while the decrease in hardness of both is similar (58.3% and 59.8%); the mechanical parameters at the induced fractures are only 53.0% to 73.6% of those in the matrix area, confirming the influence of microstructural heterogeneity. This research provides a theoretical basis and data support for optimizing hydraulic fracturing parameters, evaluating wellbore stability, and predicting the long-term development performance in tight sandstone reservoirs.
Open AccessStudy on Microscopic Pore Structure and Mechanical Characteristics of Tight Sandstone Under Hydration Effect
During the energy storage fracturing process of tight sandstone reservoirs, the pre-injection of fracturing fluid is used to supplement the formation energy, and the physical properties of rocks change under hydration. To reveal the damage mechanism of hydration on tight sandstone, the tight sandstone surrounding the Daqing Changyuan in the northern part of the Songliao Basin was taken as the research object. Through indoor static hydration experiments, combined with scanning electron microscopy (SEM), nuclear magnetic resonance (NMR), Nano-indentation experiments, and other methods, the evolution laws of rock micro-pore morphology, microfracture parameters, Young’s modulus, hardness, and other mechanical indicators under different hydration durations and soaking pressures were systematically explored. The research results show that the water–rock interaction of acidic slick water fracturing fluid significantly changes the mineral composition and microstructure of mudstone and sandstone, controls the development of induced fractures, and degrades the micro-mechanical properties of rocks, with significant lithological differences. In terms of mineral evolution, the soaking time causes the clay minerals in mudstone to increase by up to 12.0%, while pressure causes the carbonate minerals in sandstone to decrease by up to 23.3%. In terms of induced fracture development, the induced fracture widths of sandstone and mudstone under 30 MPa of pressure increase by 122.4% and 85.7%, respectively. The fracture width of mudstone shows a trend of “increasing first and then decreasing” with time, while that of sandstone decreases monotonically. In terms of micro-mechanical properties, after soaking for 168 h, the Young’s modulus of mudstone decreases by up to 66.9%, much higher than that of sandstone (29.5%), while the decrease in hardness of both is similar (58.3% and 59.8%); the mechanical parameters at the induced fractures are only 53.0% to 73.6% of those in the matrix area, confirming the influence of microstructural heterogeneity. This research provides a theoretical basis and data support for optimizing hydraulic fracturing parameters, evaluating wellbore stability, and predicting the long-term development performance in tight sandstone reservoirs.
- Open Access
- 26 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (3) , 1252
The Impact of Fracturing Engineering Parameters on the Propagation of Fractures in Infill Wells and the Evolution of the In Situ Stress Field During Waterflood Processes
This study aims to enhance the development effectiveness of infill wells in the strongly heterogeneous conglomerate reservoir of the Baikouquan Formation in the Bai 21 well area of the Junggar Basin. By optimizing the synergy between fracturing and waterflooding development, it provides a basis for improving the recovery rate of such reservoirs. Integrating geomechanical modeling, fracturing numerical simulation, and reservoir dynamic analysis, the influence mechanisms of fracturing parameters—including pumping rate, pad fluid ratio, and proppant intensity—on fracture propagation, waterflooding response, and stress field evolution were systematically investigated. The results indicate that an optimal parameter combination of a pumping rate of 3.5–4.0 m3/min, a pad fluid ratio of 40–50%, and a proppant intensity of 3.0–4.0 m3/m can create short, wide fractures with half-lengths of 40–45 m, effectively delaying water breakthrough and reducing inter-well interference. Stress field simulations further reveal non-uniform evolution during injection and production: the stress near injection wells initially increases and then decreases, dropping by 9.3% compared to the initial value, while the stress around production wells continuously decreases, with a reduction of up to 37.3%. These findings provide valuable guidance for the synergistic development of fracturing and waterflooding in infill wells in similar strongly heterogeneous conglomerate reservoirs.
- 26 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (3) , 1252
Open AccessThe Impact of Fracturing Engineering Parameters on the Propagation of Fractures in Infill Wells and the Evolution of the In Situ Stress Field During Waterflood Processes
This study aims to enhance the development effectiveness of infill wells in the strongly heterogeneous conglomerate reservoir of the Baikouquan Formation in the Bai 21 well area of the Junggar Basin. By optimizing the synergy between fracturing and waterflooding development, it provides a basis for improving the recovery rate of such reservoirs. Integrating geomechanical modeling, fracturing numerical simulation, and reservoir dynamic analysis, the influence mechanisms of fracturing parameters—including pumping rate, pad fluid ratio, and proppant intensity—on fracture propagation, waterflooding response, and stress field evolution were systematically investigated. The results indicate that an optimal parameter combination of a pumping rate of 3.5–4.0 m3/min, a pad fluid ratio of 40–50%, and a proppant intensity of 3.0–4.0 m3/m can create short, wide fractures with half-lengths of 40–45 m, effectively delaying water breakthrough and reducing inter-well interference. Stress field simulations further reveal non-uniform evolution during injection and production: the stress near injection wells initially increases and then decreases, dropping by 9.3% compared to the initial value, while the stress around production wells continuously decreases, with a reduction of up to 37.3%. These findings provide valuable guidance for the synergistic development of fracturing and waterflooding in infill wells in similar strongly heterogeneous conglomerate reservoirs.
- Open Access
Research on the Optimization of the Volume Fracturing Shut-in and Drainage System of Unconventional Reservoirs in the Erlian Block
Aiming at unclear imbibition replacement mechanisms and flowback/production strategies in unconventional reservoirs of the Erlian Block, this study proposes a systematic approach integrating “imbibition-flowback-productivity synergy” to optimize post-fracturing shut-in and production regimes. By developing numerical models incorporating geological and engineering factors, we analyzed fluid dynamics during both the shut-in and production phases. Concurrently, crude oil displacement-fracturing fluid imbibition replacement experiments were conducted to guide parameter optimization. The results indicate that optimized shut-in time and production rates substantially increase recovery efficiency while mitigating reservoir damage and proppant flowback. The well shut-in time of the Erlian Block can achieve the optimal shut-in replacement effect in about 20–25 days. The optimized flowback rate of the unconventional reservoir in the Erlian Block is 25–30 m3/d. The findings offer theoretical insights and practical recommendations for the efficient development of unconventional resources.
Open AccessResearch on the Optimization of the Volume Fracturing Shut-in and Drainage System of Unconventional Reservoirs in the Erlian Block
Aiming at unclear imbibition replacement mechanisms and flowback/production strategies in unconventional reservoirs of the Erlian Block, this study proposes a systematic approach integrating “imbibition-flowback-productivity synergy” to optimize post-fracturing shut-in and production regimes. By developing numerical models incorporating geological and engineering factors, we analyzed fluid dynamics during both the shut-in and production phases. Concurrently, crude oil displacement-fracturing fluid imbibition replacement experiments were conducted to guide parameter optimization. The results indicate that optimized shut-in time and production rates substantially increase recovery efficiency while mitigating reservoir damage and proppant flowback. The well shut-in time of the Erlian Block can achieve the optimal shut-in replacement effect in about 20–25 days. The optimized flowback rate of the unconventional reservoir in the Erlian Block is 25–30 m3/d. The findings offer theoretical insights and practical recommendations for the efficient development of unconventional resources.
- Open Access
Research and Application of Deep Coalbed Gas Production Capacity Prediction Models
The accurate prediction of single-well production performance necessitates considering the multiple factors influencing the dynamic changes in coal seam permeability during deep coalbed methane (CBM) extraction. This study focuses on Block D of the Ordos Basin. The Langmuir monolayer adsorption model was selected to describe gas adsorption behavior, and a productivity prediction model for deep CBM was developed by coupling multiple dynamic effects, including stress sensitivity, matrix shrinkage, gas slippage, and coal fines production and blockage. The results indicate that the stress sensitivity coefficients of artificial fracture networks and cleat fractures are key factors affecting the accuracy of CBM productivity predictions. Under accurate stress sensitivity coefficients, the predicted daily gas production rates of the productivity model for single wells showed errors ranging from 1.89% to 14.22%, with a mean error of 8.15%, while the predicted daily water production rates had errors between 0.35% and 17.66%, with a mean error of 8.68%. This demonstrates that the established productivity prediction model for deep CBM aligns with field observations. The findings can provide valuable references for production performance analysis and development planning for deep CBM wells.
Open AccessResearch and Application of Deep Coalbed Gas Production Capacity Prediction Models
The accurate prediction of single-well production performance necessitates considering the multiple factors influencing the dynamic changes in coal seam permeability during deep coalbed methane (CBM) extraction. This study focuses on Block D of the Ordos Basin. The Langmuir monolayer adsorption model was selected to describe gas adsorption behavior, and a productivity prediction model for deep CBM was developed by coupling multiple dynamic effects, including stress sensitivity, matrix shrinkage, gas slippage, and coal fines production and blockage. The results indicate that the stress sensitivity coefficients of artificial fracture networks and cleat fractures are key factors affecting the accuracy of CBM productivity predictions. Under accurate stress sensitivity coefficients, the predicted daily gas production rates of the productivity model for single wells showed errors ranging from 1.89% to 14.22%, with a mean error of 8.15%, while the predicted daily water production rates had errors between 0.35% and 17.66%, with a mean error of 8.68%. This demonstrates that the established productivity prediction model for deep CBM aligns with field observations. The findings can provide valuable references for production performance analysis and development planning for deep CBM wells.