HMHe Ma

He Ma

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


He Ma has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Impact of Fracturing Engineering Parameters on the Propagation of Fractures in Infill Wells and the Evolution of the In Situ Stress Field During Waterflood Processes

    by Dan Zhou, Xinfang Ma, Bo Dong, Minghai Zhang, Xiao Zhang, He Ma, Yipeng Wang, Qin Wang

    This study aims to enhance the development effectiveness of infill wells in the strongly heterogeneous conglomerate reservoir of the Baikouquan Formation in the Bai 21 well area of the Junggar Basin. By optimizing the synergy between fracturing and waterflooding development, it provides a basis for improving the recovery rate of such reservoirs. Integrating geomechanical modeling, fracturing numerical simulation, and reservoir dynamic analysis, the influence mechanisms of fracturing parameters—including pumping rate, pad fluid ratio, and proppant intensity—on fracture propagation, waterflooding response, and stress field evolution were systematically investigated. The results indicate that an optimal parameter combination of a pumping rate of 3.5–4.0 m3/min, a pad fluid ratio of 40–50%, and a proppant intensity of 3.0–4.0 m3/m can create short, wide fractures with half-lengths of 40–45 m, effectively delaying water breakthrough and reducing inter-well interference. Stress field simulations further reveal non-uniform evolution during injection and production: the stress near injection wells initially increases and then decreases, dropping by 9.3% compared to the initial value, while the stress around production wells continuously decreases, with a reduction of up to 37.3%. These findings provide valuable guidance for the synergistic development of fracturing and waterflooding in infill wells in similar strongly heterogeneous conglomerate reservoirs.


  • Open Access

    Research on the Optimization of the Volume Fracturing Shut-in and Drainage System of Unconventional Reservoirs in the Erlian Block

    by Ning Li, Xinfang Ma, Liu Xu, Changjun Long, Guohua Liu, Shuzhi Xiu, He Ma

    Aiming at unclear imbibition replacement mechanisms and flowback/production strategies in unconventional reservoirs of the Erlian Block, this study proposes a systematic approach integrating “imbibition-flowback-productivity synergy” to optimize post-fracturing shut-in and production regimes. By developing numerical models incorporating geological and engineering factors, we analyzed fluid dynamics during both the shut-in and production phases. Concurrently, crude oil displacement-fracturing fluid imbibition replacement experiments were conducted to guide parameter optimization. The results indicate that optimized shut-in time and production rates substantially increase recovery efficiency while mitigating reservoir damage and proppant flowback. The well shut-in time of the Erlian Block can achieve the optimal shut-in replacement effect in about 20–25 days. The optimized flowback rate of the unconventional reservoir in the Erlian Block is 25–30 m3/d. The findings offer theoretical insights and practical recommendations for the efficient development of unconventional resources.


  • Open Access

    Research and Application of Deep Coalbed Gas Production Capacity Prediction Models

    by Aiguo Hu, Kezhi Li, Changyu Yao, Xinchun Zhu, Hui Chang, Zheng Mao, He Ma, Xinfang Ma

    The accurate prediction of single-well production performance necessitates considering the multiple factors influencing the dynamic changes in coal seam permeability during deep coalbed methane (CBM) extraction. This study focuses on Block D of the Ordos Basin. The Langmuir monolayer adsorption model was selected to describe gas adsorption behavior, and a productivity prediction model for deep CBM was developed by coupling multiple dynamic effects, including stress sensitivity, matrix shrinkage, gas slippage, and coal fines production and blockage. The results indicate that the stress sensitivity coefficients of artificial fracture networks and cleat fractures are key factors affecting the accuracy of CBM productivity predictions. Under accurate stress sensitivity coefficients, the predicted daily gas production rates of the productivity model for single wells showed errors ranging from 1.89% to 14.22%, with a mean error of 8.15%, while the predicted daily water production rates had errors between 0.35% and 17.66%, with a mean error of 8.68%. This demonstrates that the established productivity prediction model for deep CBM aligns with field observations. The findings can provide valuable references for production performance analysis and development planning for deep CBM wells.


  • Open Access

    Optimization of Fracturing Sweet Spot in Deep Carbonate Reservoirs by Combining TOPSIS and AHP Algorithm

    by Yong Liu, Guiqi Xie, Honglin Zheng, Xinfang Ma, Guangcong Ren, Xinyuan Feng, Wenkai Zhao, He Ma, Fengyu Lei

    The deep carbonate reservoirs in the Yingzhong Block of the Qaidam Basin exhibit strong vertical heterogeneity and complex natural fracture development. Conventional fracability evaluation methods struggle to accurately characterize formation features, thereby affecting the stimulation effectiveness. To enhance the evaluation accuracy of fracturing sweet spot intervals, automatic mineral scanning equipment is employed to obtain formation micro-physical property parameters at continuous depths. Considering the temperature-pressure coupling effect under deep conditions, a rock mechanics computational model based on mineral composition was established to derive macroscopic mechanical parameters such as brittleness index and in situ stress. Based on a combined algorithm of the improved Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) and Analytic Hierarchy Process (AHP), a fracturing sweet spot prediction model integrating micro- and macro-multi-factors is established, and sweet spot index levels are classified. The research results indicate that the rock mechanics computational model demonstrates high accuracy, the calculated macroscopic parameters are reliable, and the fracturing sweet spot index model can fracability and meticulously evaluate the characteristics of deep carbonate formations. The fracturing sweet spots can be classified into three levels: Level I with an index higher than 0.50, Level II with an index between 0.35 and 0.50, and Level III with an index lower than 0.35. After using this method for layer selection, the fracture pressure decreases by 11.6%, and the sand addition success rate increases by 24%. Applying this method to guide the optimization of fracturing intervals demonstrates good on-site practical value, providing an important reference for identifying fracturing sweet spots in deep carbonate reservoirs.


  • Open Access

    Three-Dimensional Geomechanical Modeling and Hydraulic Fracturing Parameter Optimization for Deep Coalbed Methane Reservoirs: A Case Study of the Daniudi Gas Field, Ordos Basin

    by Xugang Liu, Xiang Wang, Fuhu Chen, Xinchun Zhu, Zheng Mao, Xinyu Liu, He Ma

    Deep coalbed methane (CBM) resources represent a significant opportunity for future exploration and development. The combination of horizontal well drilling and hydraulic fracturing technology has emerged as the most efficient method for extracting deep CBM. By optimizing the fracturing parameters for horizontal wells, we can improve the effectiveness of reservoir stimulation even further. In this paper, taking the deep coalbed methane in the Daniudi gas field in the Ordos Basin as the research object, using Numerical simulation software such as Petrel, comprehensively considering the field logging, logging data and laboratory experimental data of rock mechanical parameters, the three-dimensional geomechanical and stress field model of deep coalbed methane is established, and on this basis, the numerical simulation research on the fracture network expansion and construction parameter optimization of single well and well group is carried out. Through the qualitative evaluation of fracture network morphology, the change of in situ stress field, the quantitative evaluation of post-pressure conductivity and fracture volume, the section spacing, construction fluid volume, and construction displacement under the conditions of single well and well group were optimized. The results show that under the condition of a certain well spacing, the fracture propagation of the well group is affected by stress shadowing and channeling, and the fracture pattern is more complex, and the construction scale is smaller than that of a single well. These findings provide critical insights for improving the efficiency of deep CBM recovery.