AMAnatolii Mukhachev

Anatolii Mukhachev

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Anatolii Mukhachev has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • PRODUCTION OF NUCLEAR‑GRADE ZIRCONIUM AND HAFNIUM TETRAFLUORIDES

    by A.P. Mukhachev, D.O. Yelatontsev, O.A. Kharytonova, V.G. Shevchenko

    This paper presents the results of industrial‑scale trials of a technology for producing high‑purity zirconium and hafnium tetrafluorides. Nuclear‑grade purity of the zirconium and hafnium nitrate salts is achieved through the high extraction kinetics enabled by the EC-250 and CET-125 centrifugal extractors. It was demonstrated that, to ensure complete conversion of zirconium and hafnium into insoluble fluorides, the solutions must first be concentrated to saturation by vacuum evaporation at 70…95 °C. The tetrafluoride monohydrates of zirconium and hafnium were precipitated using 40% HF and anhydrous hydrogen fluoride as the precipitating agents. The lowest residual content of zirconium and hafnium in the mother liquor was obtained when using anhydrous hydrogen fluoride. Removal of the water of crystallization was accomplished by drying at 120 °C, followed by thermal treatment of the salts at 650 °C under a flow of hydrogen fluoride and dry argon. The resulting fluorides, obtained in the β‑phase, exhibited a purity of 99.9% and a moisture content below 0.05%. They fully met the requirements for the standard electrolysis process based on K₂ZrF₆ and K₂HfF₆. Both salts successfully completed a full cycle of process validation, during which zirconium and hafnium powders with a purity of no less than 99.85% were produced.

  • Environmental and technological aspects of uranium production in Ukraine

    by Anatolii Mukhachev, Dmytro Yelatontsev, Victor Zhdanov, Victor Yakovlyev, Grzegorz Wałowski

  • Open Access

    Фосфогіпс – нетрадиційне джерело рідкісноземельних елементів: досвід України

    by A. P. Mukhachev, D. O. Yelatontsev, L. H. Mesheryakov, O. A. Kharytonova, Л. Г. Мещеряков

    Викладено результати досліджень комплексної переробки мінеральної сировини техногенного походження – фосфогіпсу, одержаного у процесі виробництва фосфорних добрив. Існуючі технології переробки фосфогіпсу, що застосовуються у промислових масштабах, розраховані на отримання матеріалів переважно будівельного призначення. Враховуючи гострий дефіцит рідкісноземельних елементів, викликаний бурхливим розвитком сучасних наукоємних галузей науки і техніки, використання фосфогіпсу як джерела цих критичних металів становить безперечний практичний інтерес. Показано, що конверсія фосфогіпсу розчинами карбонатних сполук на основі амонію, калію і натрію дозволяє одержати цінні хімічні сполуки, добрива і солі, а фосфокрейда, що попутно утворюється, може слугувати сировиною для отримання хімічно чистої крейди й азотних добрив на основі нітратів кальцію й амонію. Встановлено, що при конверсії фосфогіпсу карбонатами амонію, натрію або калію відбувається збагачення сировини рідкісноземельними елементами до 5 % та стронцію до 12 %. Враховуючи високу вартість індивідуальних рідкісноземельних елементів, зокрема неодиму, лантану та гадолінію, доцільно розділяти сумарний концентрат рідкісноземельних елементів на концентрати легкої та середньоважкої груп, з яких потім виділяти парні концентрати типу лантан-церій, неодим-празеодим для одержання більш дорогих типів продукції. Мінеральні добрива NH4NO3, (NH4)2SO4, Ca(NO3)2, попутно отримані з фосфогіпсу, є дуже цінними для сільського господарства через практично нульову вартість фосфогіпсу. Представлено результати розробки комплексної технології конверсії фосфогіпсу з одержанням широкої номенклатури рентабельної продукції, а також способи вилучення та розподілу рідкісноземельних елементів. Високі показники ефективності технологічних рішень, отримані в роботі, дозволяють рекомендувати розроблену технологію для реалізації сталої конверсії фосфогіпсу як в Україні, так і за її межами.

  • Combined purification of coal mine methane and mine water by the gas hydrate method to produce hydrogen

    by Volodymyr Shevchenko, Anatolii Mukhachev, Dmytro Yelatontsev, Ihor Luts, Ivan Zezekalo, Mykhailo Pedchenko, Ihor Belikov

    This study demonstrates the technology of the combined purification of mine water and mine methane through the utilization of gas hydrates; purified methane is to be subjected to plasma pyrolysis. Given the considerable variability in the flow rate and concentration of methane, the objective was to identify a viable methodology for the utilisation of mine gas wherein the volumetric quantity and component composition of the gas would not be restrictive parameters. The proposed approach involves the transformation of coal mine gas into a hydrated form. The combination of a coal mine methane-air mixture with mine water to form hydrated gas facilitates the dual objectives of utilizing coal mine gas and desalinating mine water within a single technological process, thereby yielding pure methane, drinking water, and dry salts as final products. Collectively, these advancements enable the generation of new beneficial products, promote the comprehensive development of coal deposit resources, and markedly mitigate the deleterious effects on the environment. A chemical analysis of mine water was conducted, revealing significant mineralization levels that categorize the mine water as saline and underscore the imperative for desalination. The properties and chemical composition of mine methane gas taken from surface degassing wells were analysed. The analytical data indicate that the composition of coal mine methane is close to natural gas, with notable homologues including ethane and propane. The gas mixture is also characterized by the presence of nitrogen (1.69–4.65%), as well as lesser quantities of oxygen (0.08–0.29%) and carbon dioxide (0.19–0.40%). Further analysis of the data reveals fluctuations in methane concentration under varying operational conditions of the wells throughout their functional lifespan. The extracted methane is optimally suited for utilization as a precursor in the generation of what is termed ‘turquoise’ hydrogen, applying the technology of steam-plasma pyrolysis. We delineate various strategies and methodologies that could be employed to harness substantial volumes of mine water and gas from coal deposits for the production of hydrogen fuel, desalinated water, and technical salts as resultant products. The resultant water, possessing adequate quality, is anticipated to avert the contamination of aquatic ecosystems with dissolved mineral salts. Potential beneficiaries of the combined processing technology of mineralized mine water may encompass coal enterprises, joint-stock companies, and, in the foreseeable future, entities within other extractive industries.

  • Nuclear reactor zirconium alloys quality issues

    by M.S. Poliakov Institute of Geotechnical Mechanics of the National Academy of Sciences of Ukraine, Anatolii Mukhachev, Mykola Pylypenko, National Science Centre Kharkiv Institute of Physics and Technology of National Academy of Sciences of Ukraine, Dmytro Yelatontsev, Volodymyr Shevchenkо, Olena Kharytonova, Masaryk University

    The solution to increase the degree of nuclear fuel burnup and to extend the service life of fuel assemblies (FAs) to 5–7 years is largely related to improving existing production technologies and developing new, more radiation- and corrosion-resistant alloys. This paper analyses the industrial technologies for producing reactor-pure zirconium alloys for producing products operating in the core of thermal neutron reactors (BWR, PWR, VVER). Research demonstrates that the processes of zirconium concentrate opening, the efficiency of zirconium and hafnium extraction separation, and the refining of the alloy by electron beam melting determine the purity of zirconium alloys. It has been established that oxygen is an alloying element, and its optimal concentration should be from 0.10 to 0.14%. The new soda-extraction fluoride-calcium-thermal technology developed in Ukraine has the most efficient refining processes that ensure the purity of zirconium-niobium alloys at ≥99.94%. This makes it possible to improve the corrosion and radiation resistance of the alloys by reducing the impurity content to 0.05%. Industrial technologies for the production of zirconium alloys for reactor use do not allow achieving a purity level of more than 99.8%. This limits the lifetime of nuclear fuel to 4 years and its burnup rate to 50 mW∙day/kgU. Calcium-thermal zirconium and alloys based on it, such as E110, have special chemical compositions and physical and mechanical properties. The data presented in the review show that, in terms of chemical composition, one of the main tasks of researchers and technologists at the present stage is to study the role of oxygen impurity in ensuring the required service characteristics of alloys based on E110. The increased yield strength and hardness values of E110 and E125 alloys raise the challenge of improving the technology of forming pipe billets and the deformation treatment of alloys. More complex are the tasks associated with ensuring radiation and corrosion resistance, reducing radiation embrittlement, and swelling of alloys. The review offers technical solutions and technological methods that can ensure the required quality of alloys under the requirements of national and international quality standards.


  • AN EFFECTIVE BIOSORBENT DERIVED N EFFECTIVE BIOSORBENT DERIVED FROM PRODUCTION WASTE ROM PRODUCTION WASTE FOR WATER TREATMENT: STUDYING OR WATER TREATMENT: STUDYING THE ADSORPTION OF SYNTHETIC DYES HE ADSORPTION OF SYNTHETIC DYES

    by Dmytro Yelatonsev, Anatoliy Mukhachev, Olena Ivanyuk

    Introduction. Eco-friendly disposal of food waste, in particular, nutshells and fruit kernels, is an important issue to ensure sustainable nature management. These secondary raw materials are the source of valuable polymeric materials, cellulose and lignin.Problem Statement. IGiven the capacity of the food industry in Ukraine and the amount of waste produced, the development of technologies for processing lignin-cellulose biomass is an important research and practical issue.Purpose. The purpose of this research is to study the adsorption properties of chemically modified biosorbent based on plant materials concerning synthetic dyes of different types and classes; to assess the feasibility of biosorbent production and efficiency of its application in water treatment.Materials and Methods. Lignocellulose sorbent (LCS) has been synthesized from non-wood raw materials by chemical modification with the use of phosphoric acid with the addition of urea in an aqueous media. The Fourier transform infrared and standard methods of plant raw material analysis have been used to determine the physicochemical characteristics of LCS. The adsorption of anionic (methyl orange, alizarin red S, eosin Y), cationic (methylene blue, neutral red), and nonionic (aniline yellow) dyes on LCS from aqueous solution has been studied in the batch mode.Results. The adsorption capacity of LCS towards cationic dyes (47.0–53.3 mg/g) is higher than that of anionic (22.2–36.9 mg/g) and nonionic (4.7 mg/g) ones. The adsorption kinetics have been adequately described by a pseudo-second-order equation. Adsorption of all classes of dyes on LCS is thermodynamically feasible, spontaneous, and endothermic process. The liquid by-product of LCS production contains 15% nitrogen and 10% phosphorus, so it may be used as a fertilizer. Conclusions. The proposed method for processing food waste provides obtaining effective sorbent and liquid NP-fertilizer. LCS removes both cationic and anionic pollutants from water, so it may be considered a promisingbiosorbent for water purification.


  • Sorption of Uranium and Rare-Earth Elements to Remove Radioactive Impurities in the Processing of Phosphate-containing Raw Materials

    by D. A. Elatontsev, A. P. Mukhachev, Yu. F. Korovin, N. D. Voloshin

    The process of sorption separation of uranium and REE after acid leaching of uranium-phosphorus-rare-earth chemical concentrate onto a modified granular sorbent based on cellulose phosphate (MGCP) was studied. It was found that MGCP efficiently absorbs U(VI) from solution, while REEs remain together with phosphorus and fluorine in the raffinate. The dependences of the exchange capacity of MGCP for U(VI) and REE on the volume of the passed filtrate were determined. The dynamic capacity of the sorbent for U(VI) reaches 100 mg/g, and the degree of extraction of U(VI) from the solution exceeds 94%. It has been shown that it is expedient to desorb uranium with a (NH4)2CO3 solution at a temperature of 50 ± 2°C, providing preliminary oxidation of U(IV) to U(VI) directly on the sorbent with a 0.5% HNO3 solution containing 2% NaNO2. With sorption of U(VI) on MGCP, the stage of extraction purification from REE in the production of triuranium octoxide may be excluded. The possibility of sorption separation of REE from radioactive isotopes on MGCP was determined. The sorbent capacity for REE is 70 mg/g.


  • Industrial technology of processing carbonaceous uranium ore in Ukraine

    by Institute of Geotechnical Mechanics named by N. Poljakov of National Academy of Sciences of Ukraine, Anatolii Mukhachev, Dmytro Yelatontsev, Dnipro State Technical University, Volodymyr Nefedov, Ukrainian State University of Chemical Technology

    The purpose of the study was to represent the results of the first industrial tests of the technology for processing uranium carbonate ore with a target component content of 0.3%, by selective carbonate leaching with the separation of the uranium-containing solution from the rock, in the processes of thickening and decantation with using flocculants. This study was carried out to find out more effective flocculating reagents. Experimental data were collected from industrial slurries with the addition of polyacrylamide-based flocculants. The study showed that leaching in sodium carbonate media provided a high degree of purity of the product because metals impurities during leaching did not pass into solution. In line with earlier research, the process studies have confirmed the hypothesis that replacing of low-performance disc filters with automatic settling tanks significantly reduces labor and energy consumption. The results of the study convincingly show that the scheme for processing carbonate uranium ore made it possible to reduce the time of personnel contact with toxic and radioactive products. The main technical and economic indicators of the decantation scheme are given, methods for improving the decantation washing of uranium from pulps are described. Methods for more efficient use of flocculants and reduction of their consumption are proposed. Optimal modes of the process allowed to increase productivity and reduce production costs by 10% at the expense to reduce the consumption of electricity and steam, decommission energy-intensive vacuum pumps and filters. At the same time, the average extraction of uranium in the commercial solution – 90%. The results obtained can be applied in the uranium mining industry. To increase the productivity of the decantation scheme, further tests of new flocculating reagents, methods of their introduction are necessary; it is also of practical interest to study the conditions of flocculation depending on the salt composition of the washing solutions.