Svetlana Naumenko
Research Subjects
Svetlana Naumenko has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Valery Subotovich
Anatolii Pidhornyi Institute of Power Machines and Systems of the National Academy of Sciences of Ukraine
6 shared publications - Alexander Lapuzin
National Technical University “Kharkiv Polytechnic Institute
5 shared publications - Yuriy Yudin
National Technical University “Kharkiv Polytechnic Institute
5 shared publications Олександр Лапузін
Національний технічний університет «Харківський політехнічний інститут
4 shared publicationsЮрій Юдін
Національний технічний університет «Харківський політехнічний інститут
4 shared publications- Ivan Malymon
National Technical University “Kharkiv Polytechnic Institute”, Kharkiv, Ukraine
2 shared publications
Latest Publications
- Open Access
- 29 May 2026
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1,p. 17-25
The Influence of Gas-Dynamic Characteristics of Blade Cascades and Mode Criteria of an Elementary Turbine Stage on the Its Efficiency
Consideration is given to the effect of the mode criteria u2/Cф and lф on the degree of reactivity and relative blade and hydraulic efficiency coefficients (REC) of the active and reactive types of stages. It has been proved that with a decrease in power of a multi-stage turbine with nozzle steam distribution by several times, an abrupt drop in the relative blade efficiency of the regulating stage largely depends not only on the decrease in the u2/Cф, criterion, but also on the various increase in the lф criterion. The effect of the lф criterion on the hydraulic efficiency of the stages of the reactive type is within 2 % and it can be both negative and positive depending on the ratio between the cascade speed coefficients. A detailed analysis of the reasons affecting the relative blade efficiency of the last stage of a steam turbine under conditions of a change in the volumetric steam flow rate is impossible without analyzing the changes that occur in the operation of each elementary flow jet, i.e., the nature of a change in its shape, the aerodynamic characteristics of the cascades, and the local operating parameters lф and u2/Cф. For a group of turbine stages, a set of three parameters was revealed, the effect of which on the hydraulic efficiency and the degree of reactivity is identical to the effect of the operating criterion lф. Using another set, we managed to combine the calculated results of the effect on hydraulic efficiency and the degree of reactivity of the parameters of non-cylindricality of the flowand the angle of flow exit from the nozzle cascade.
- 29 May 2026
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1,p. 17-25
Open AccessThe Influence of Gas-Dynamic Characteristics of Blade Cascades and Mode Criteria of an Elementary Turbine Stage on the Its Efficiency
Consideration is given to the effect of the mode criteria u2/Cф and lф on the degree of reactivity and relative blade and hydraulic efficiency coefficients (REC) of the active and reactive types of stages. It has been proved that with a decrease in power of a multi-stage turbine with nozzle steam distribution by several times, an abrupt drop in the relative blade efficiency of the regulating stage largely depends not only on the decrease in the u2/Cф, criterion, but also on the various increase in the lф criterion. The effect of the lф criterion on the hydraulic efficiency of the stages of the reactive type is within 2 % and it can be both negative and positive depending on the ratio between the cascade speed coefficients. A detailed analysis of the reasons affecting the relative blade efficiency of the last stage of a steam turbine under conditions of a change in the volumetric steam flow rate is impossible without analyzing the changes that occur in the operation of each elementary flow jet, i.e., the nature of a change in its shape, the aerodynamic characteristics of the cascades, and the local operating parameters lф and u2/Cф. For a group of turbine stages, a set of three parameters was revealed, the effect of which on the hydraulic efficiency and the degree of reactivity is identical to the effect of the operating criterion lф. Using another set, we managed to combine the calculated results of the effect on hydraulic efficiency and the degree of reactivity of the parameters of non-cylindricality of the flowand the angle of flow exit from the nozzle cascade.
- 30 December 2025
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1,p. 16-28
The Parameters Influence of Noncylindrical Flow on the Elementary Turbine Stage Efficiency Criteria
A one-dimensional calculation method for a turbine stage with arbitrary meridional outlines has been developed. The method allows, taking into account the compressibility of the gas medium, to analyze the influence of the velocity coefficients of the nozzle and rotor cascades, the angles of the one-dimensional spatial axisymmetric flow in front of and behind the rotor cascade, and some other parameters on the degree of reactivity, cascade efficiency, and flow parameters in front of and behind the rotor cascade (RC). The influence of four parameters of non-cylindricality of the flow on the degree of reactivity of the stage and the efficiency coefficients (EffC) is considered. Hydraulic efficiency, which takes into account losses in the stage nozzle and rotor cascades, is virtually independent of the flow stream expansion rate in the rotor cascade and the magnitude of the radial velocity component behind this cascade. Increasing the radial velocity component upstream of the rotor cascade and increasing the average radius of the flow stream in the rotor cascade can reduce hydraulic efficiency by several percent. This can also be observed when the velocity coefficient of the working cascade is considered independent of these parameters. Further research is needed to determine the degree of influence of the radial velocity component on the speed coefficients of the nozzle and rotor cascade. Relative blading efficiency and stage power depend on cascade losses and the magnitude of the outlet velocity losses. A high radial velocity component downstream of the last stages of steam and gas turbines can increase outlet velocity losses and reduce relative blading efficiency by 6–8 %. The degree of flow expansion in the rotor blade has a significantly lesser effect on this efficiency and stage power.
- 30 December 2025
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1,p. 16-28
The Parameters Influence of Noncylindrical Flow on the Elementary Turbine Stage Efficiency Criteria
A one-dimensional calculation method for a turbine stage with arbitrary meridional outlines has been developed. The method allows, taking into account the compressibility of the gas medium, to analyze the influence of the velocity coefficients of the nozzle and rotor cascades, the angles of the one-dimensional spatial axisymmetric flow in front of and behind the rotor cascade, and some other parameters on the degree of reactivity, cascade efficiency, and flow parameters in front of and behind the rotor cascade (RC). The influence of four parameters of non-cylindricality of the flow on the degree of reactivity of the stage and the efficiency coefficients (EffC) is considered. Hydraulic efficiency, which takes into account losses in the stage nozzle and rotor cascades, is virtually independent of the flow stream expansion rate in the rotor cascade and the magnitude of the radial velocity component behind this cascade. Increasing the radial velocity component upstream of the rotor cascade and increasing the average radius of the flow stream in the rotor cascade can reduce hydraulic efficiency by several percent. This can also be observed when the velocity coefficient of the working cascade is considered independent of these parameters. Further research is needed to determine the degree of influence of the radial velocity component on the speed coefficients of the nozzle and rotor cascade. Relative blading efficiency and stage power depend on cascade losses and the magnitude of the outlet velocity losses. A high radial velocity component downstream of the last stages of steam and gas turbines can increase outlet velocity losses and reduce relative blading efficiency by 6–8 %. The degree of flow expansion in the rotor blade has a significantly lesser effect on this efficiency and stage power.
- Open Access
- 29 December 2024
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1,p. 21-29
The Effect of Mach and Reynolds Numbers on the Aerodynamic Characteristics of the Nozzle Cascade of a Gas Turbine
The data of experimental studies of a circular nozzle cascade for a small-sized gas turbine with a medium ratio of the diameter to the blade height as part of a turbine stage, as well as in conditions of joint operation with a radial diffuser have been presented. In the presence of an impeller, the Mach number varied in the range of 0.3 to 0.85, and in static conditions it varied in the range of 0.3 to 1.4. The flow rate coefficient was determined by the integral method using drains, and the loss coefficients and averaged flow angles were determined based on the data of detailed measurements of the flow parameters behind the cascade using pneumometric probes. The aerodynamic efficiency of the nozzle cascade is at a very high level and in the calculated transonic mode the kinetic energy loss coefficient is 0.052, and the total loss coefficient is 0.09. For modes, where the Mach number is equal to 0.6, a very strong effect of the boundary conditions behind the nozzle cascade on its aerodynamic characteristics is recorded and it is indicative of the drawbacks of experiments without an impeller. It is established that the impeller can be abandoned if the Mach number exceeds 0.85. It is also established that for a Mach number above 1.15, the Reynolds number of 10,5×105 is self-similar for the flow rate coefficient. When the Mach number is increased to 1.25, the nozzle cascade is completely closed, and the flow coefficient in the self-similarity zone reaches a maximum in terms of the Reynolds number. For the thermal calculations of the stage, the averaged angle of the flow exit from the nozzle cascade and its total loss coefficient that takes into account not only kinetic energy losses, but also kinematic losses should be used.
- 29 December 2024
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1,p. 21-29
Open AccessThe Effect of Mach and Reynolds Numbers on the Aerodynamic Characteristics of the Nozzle Cascade of a Gas Turbine
The data of experimental studies of a circular nozzle cascade for a small-sized gas turbine with a medium ratio of the diameter to the blade height as part of a turbine stage, as well as in conditions of joint operation with a radial diffuser have been presented. In the presence of an impeller, the Mach number varied in the range of 0.3 to 0.85, and in static conditions it varied in the range of 0.3 to 1.4. The flow rate coefficient was determined by the integral method using drains, and the loss coefficients and averaged flow angles were determined based on the data of detailed measurements of the flow parameters behind the cascade using pneumometric probes. The aerodynamic efficiency of the nozzle cascade is at a very high level and in the calculated transonic mode the kinetic energy loss coefficient is 0.052, and the total loss coefficient is 0.09. For modes, where the Mach number is equal to 0.6, a very strong effect of the boundary conditions behind the nozzle cascade on its aerodynamic characteristics is recorded and it is indicative of the drawbacks of experiments without an impeller. It is established that the impeller can be abandoned if the Mach number exceeds 0.85. It is also established that for a Mach number above 1.15, the Reynolds number of 10,5×105 is self-similar for the flow rate coefficient. When the Mach number is increased to 1.25, the nozzle cascade is completely closed, and the flow coefficient in the self-similarity zone reaches a maximum in terms of the Reynolds number. For the thermal calculations of the stage, the averaged angle of the flow exit from the nozzle cascade and its total loss coefficient that takes into account not only kinetic energy losses, but also kinematic losses should be used.
- Open Access
- 7 August 2023
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1-2,p. 28-36
Peculiarities of the Calculations of the Gas Turbine Cooling Systems
Системи охолодження газових турбін мають розгалужені мережи різноманітних каналів, гідравлічні та теплообмінні можливості яких визначають необхідну витрату повітря для охолодження деталей турбін і, таким чином, безпосередньо впливають на економічність ГТУ. Елементами систем охолодження, зокрема, є дроселі, діафрагми, ущільнення, отвори, які є регулюючими органами, або елементами, які піддержують тиск в системі. У каналах такого типу, як правило, має місто значне падіння тиску і тому при розрахунках потрібно дуже прискіпливо враховувати зміну щільності повітря уздовж каналу. Тому тут наведено розроблений авторами метод визначення гідравлічного опору в отворах, який дуже добре збігається з експериментальними даними. Показано, як слід враховувати стисливість повітря на коефіцієнт гідравлічного опору каналів охолодження, що дозволяє застосовувати численні експериментальні залежності для коефіцієнтів гідравлічного опору нестисливих рідин. Запропоновано метод розрахунку гідравлічних опорів отворів шляхом дефрагментації їхнього загального гідравлічного опору на окремі компоненти. Створено узагальнену залежність для гідравлічного опору розвантажувальних отворів у дисках, у монтажних зазорах між хвостовиками лопаток та дисками з урахуванням поперечних потоків повітря.
- 7 August 2023
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1-2,p. 28-36
Open AccessPeculiarities of the Calculations of the Gas Turbine Cooling Systems
Системи охолодження газових турбін мають розгалужені мережи різноманітних каналів, гідравлічні та теплообмінні можливості яких визначають необхідну витрату повітря для охолодження деталей турбін і, таким чином, безпосередньо впливають на економічність ГТУ. Елементами систем охолодження, зокрема, є дроселі, діафрагми, ущільнення, отвори, які є регулюючими органами, або елементами, які піддержують тиск в системі. У каналах такого типу, як правило, має місто значне падіння тиску і тому при розрахунках потрібно дуже прискіпливо враховувати зміну щільності повітря уздовж каналу. Тому тут наведено розроблений авторами метод визначення гідравлічного опору в отворах, який дуже добре збігається з експериментальними даними. Показано, як слід враховувати стисливість повітря на коефіцієнт гідравлічного опору каналів охолодження, що дозволяє застосовувати численні експериментальні залежності для коефіцієнтів гідравлічного опору нестисливих рідин. Запропоновано метод розрахунку гідравлічних опорів отворів шляхом дефрагментації їхнього загального гідравлічного опору на окремі компоненти. Створено узагальнену залежність для гідравлічного опору розвантажувальних отворів у дисках, у монтажних зазорах між хвостовиками лопаток та дисками з урахуванням поперечних потоків повітря.
- Open Access
- 8 July 2023
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1-2,p. 11-17
The Method of Determining Total Losses in the Nozzle Cascades of Turbomachines
To assess the level of aerodynamic efficiency of the nozzle cascades of steam and gas turbines, the method was suggested to determine the total loss coefficient instead of kinetic energy loss coefficient that takes into account both kinetic energy losses and kinematic losses. This method allows us to transform the original non-uniform spatial flow behind the cascade into an axisymmetric cylindrical flow. In the tested annular cascade with cylindrical meridional boundaries, the total loss coefficient is approximately 0.02 higher than the kinetic energy loss coefficient. By taking into account kinematic losses when performing thermal calculations for the turbines we eliminate the need for an unjustified correction of the kinetic energy loss coefficient of the nozzle cascade by 0.01–0.03, increasing thus the accuracy of calculations. To analyze the operation of individual sections of the nozzle cascade and to determine the relationship between kinetic energy losses and kinematic losses, it is advisable to use the averaging method proposed in 2021 that enables the transformation of the initial non-uniform spatial flow behind the cascade into an axisymmetric conical flow. The aerodynamic characteristics of this flow are the widely used kinetic energy loss factor and two averaged flow angles.
- 8 July 2023
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1-2,p. 11-17
Open AccessThe Method of Determining Total Losses in the Nozzle Cascades of Turbomachines
To assess the level of aerodynamic efficiency of the nozzle cascades of steam and gas turbines, the method was suggested to determine the total loss coefficient instead of kinetic energy loss coefficient that takes into account both kinetic energy losses and kinematic losses. This method allows us to transform the original non-uniform spatial flow behind the cascade into an axisymmetric cylindrical flow. In the tested annular cascade with cylindrical meridional boundaries, the total loss coefficient is approximately 0.02 higher than the kinetic energy loss coefficient. By taking into account kinematic losses when performing thermal calculations for the turbines we eliminate the need for an unjustified correction of the kinetic energy loss coefficient of the nozzle cascade by 0.01–0.03, increasing thus the accuracy of calculations. To analyze the operation of individual sections of the nozzle cascade and to determine the relationship between kinetic energy losses and kinematic losses, it is advisable to use the averaging method proposed in 2021 that enables the transformation of the initial non-uniform spatial flow behind the cascade into an axisymmetric conical flow. The aerodynamic characteristics of this flow are the widely used kinetic energy loss factor and two averaged flow angles.
- Open Access
- 28 December 2022
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1-2,p. 23-31
Studying the Effect of the Tangential Nonuniformity of Flow Parameters on Gas Dynamic Performances of the Nozzle Cascades of Turbine Machines
Aerodynamic efficiency of the nozzle cascades of steam and gas turbines is defined by many factors and one of them is the tangential and radial nonuniformity degree of the parameters of a spatial flow behind the cascades. The averaging of these parameters enables the determination of the integral parameters of the cascades, in particular two flow angles and the velocity angle or the kinetic energy loss coefficient. The angle that takes into account the level of the averaged radial component of the velocity defines the level of kinematic losses in the cascade. Even in the case of the cylindric boundaries of the cascade this angle differs from zero and kinematic losses decrease the cascade efficiency by 30 to 50 percent. This scientific paper gives the results of experimental investigations of the effect of the circumferential nonuniformity of the velocity and the angles of the spatial flow on kinematic losses at different radii of the nozzle cascade of the last stage of the steam turbine and the nozzle cascade of the first stage of the gas turbine. The kinetic energy loss coefficient and the coefficient of total losses were suggested as the integral characteristics of the cascades. In the case of cylindric boundaries of the stage the total loss-to-kinetic energy loss ratio is noticeably decreased during the transition from the average zone to the zone of end losses. However, in the peripheral zone of the nozzle cascade of the last stage of steam turbine total losses are three times higher than kinetic energy losses due to the fact that the radial component of the velocity behind the cascade is much higher than the flow rate component and the level of the losses of kinetic energy is not high.
- 28 December 2022
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1-2,p. 23-31
Open AccessStudying the Effect of the Tangential Nonuniformity of Flow Parameters on Gas Dynamic Performances of the Nozzle Cascades of Turbine Machines
Aerodynamic efficiency of the nozzle cascades of steam and gas turbines is defined by many factors and one of them is the tangential and radial nonuniformity degree of the parameters of a spatial flow behind the cascades. The averaging of these parameters enables the determination of the integral parameters of the cascades, in particular two flow angles and the velocity angle or the kinetic energy loss coefficient. The angle that takes into account the level of the averaged radial component of the velocity defines the level of kinematic losses in the cascade. Even in the case of the cylindric boundaries of the cascade this angle differs from zero and kinematic losses decrease the cascade efficiency by 30 to 50 percent. This scientific paper gives the results of experimental investigations of the effect of the circumferential nonuniformity of the velocity and the angles of the spatial flow on kinematic losses at different radii of the nozzle cascade of the last stage of the steam turbine and the nozzle cascade of the first stage of the gas turbine. The kinetic energy loss coefficient and the coefficient of total losses were suggested as the integral characteristics of the cascades. In the case of cylindric boundaries of the stage the total loss-to-kinetic energy loss ratio is noticeably decreased during the transition from the average zone to the zone of end losses. However, in the peripheral zone of the nozzle cascade of the last stage of steam turbine total losses are three times higher than kinetic energy losses due to the fact that the radial component of the velocity behind the cascade is much higher than the flow rate component and the level of the losses of kinetic energy is not high.
- 30 December 2021
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 3,p. 5-11
Flow Characteristics of the Nozzle Blade Cascade in the Mode of the Joint Operation with the Radial Diffuser
The obtained research data are given for the nozzle cascade used by a small-size gas turbine of an average fanning in combination with the radial diffuser. Aerodynamic characteristics of the nozzle blade cascade were determined in a wide range of a change in the Reynolds number varying from 4∙105 to 106 and the reduced velocity varying in the range of 0.4 to 1.13. The flow rate coefficient of the nozzle cascade was derived for all modes using the integral methods and the drainages behind the cascade. The kinetic energy loss coefficient and the flow angles were calculated using the measurement data of flow parameters in three control modes that were obtained due to the use of orientable pneumometric probes. When the expansion degree of the convergent –divergent annular duct behind the cascade is equal to 1.43 the flow in the narrow section of this duct is “enlocked” in the mode when the reduced velocity behind the cascade is equal to 1.127. At such velocity the Reynolds number 106 is self-similar for the flow rate coefficient. At lower values of Reynolds number, the decrease of it is accompanied by an intensive decrease in the flow rate coefficient for all the values of the reduced velocity. For the Reynolds number lower than 7∙105 an increase in the velocity results in a decreased flow rate coefficient. When this number exceeds 8∙105 an increase in the velocity results in an increase of the flow coefficient up to the moment when the flow is “enlocked” in the nozzle cascade.
- 30 December 2021
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 3,p. 5-11
Flow Characteristics of the Nozzle Blade Cascade in the Mode of the Joint Operation with the Radial Diffuser
The obtained research data are given for the nozzle cascade used by a small-size gas turbine of an average fanning in combination with the radial diffuser. Aerodynamic characteristics of the nozzle blade cascade were determined in a wide range of a change in the Reynolds number varying from 4∙105 to 106 and the reduced velocity varying in the range of 0.4 to 1.13. The flow rate coefficient of the nozzle cascade was derived for all modes using the integral methods and the drainages behind the cascade. The kinetic energy loss coefficient and the flow angles were calculated using the measurement data of flow parameters in three control modes that were obtained due to the use of orientable pneumometric probes. When the expansion degree of the convergent –divergent annular duct behind the cascade is equal to 1.43 the flow in the narrow section of this duct is “enlocked” in the mode when the reduced velocity behind the cascade is equal to 1.127. At such velocity the Reynolds number 106 is self-similar for the flow rate coefficient. At lower values of Reynolds number, the decrease of it is accompanied by an intensive decrease in the flow rate coefficient for all the values of the reduced velocity. For the Reynolds number lower than 7∙105 an increase in the velocity results in a decreased flow rate coefficient. When this number exceeds 8∙105 an increase in the velocity results in an increase of the flow coefficient up to the moment when the flow is “enlocked” in the nozzle cascade.