Volodymyr Musiiko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Volodymyr Musiiko has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Anatolii Korpach
Department of Engines and Thermal Engineering, Faculty of Automotive and Mechanical Engineering, National Transport University, 1, M. Omelianovycha-Pavlenka Str., 010 10 Kyiv, Ukraine
2 shared publications - Andrii Koval
Faculty of Automotive and Mechanical Engineering, National Transport University, M. Omelianovicha-Pavlenka, 1, 01010 Kiev, Ukraine
2 shared publications - Mykhailo Honchar
Faculty of Automotive and Mechanical Engineering, National Transport University, M. Omelianovicha-Pavlenka, 1, 01010 Kiev, Ukraine
2 shared publications Aleksandr Yaryzhko
1 shared publication- Andrej Suchánek
Department of Transport and Handling Machines, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
1 shared publication - Jakub Mosciszewski
Department of Technical Systems Engineering, Rzeszow University of Technology, 35-959 Rzeszow, Poland
1 shared publication
Latest Publications
- Open Access
- 29 December 2022
- Published by Kharkiv National Automobile and Highway University in Bulletin of Kharkov National Automobile and Highway University
- No. 99,p. 151
Current technical condition of main pipelines and assessment of environmental safety during trans-portation of energy carriers through them
У статті наведено аналіз технічного стану магістральних трубопроводів та запропоновано ефективні шляхи його покращення. Розроблено методику та шкалу оцінки екологічної безпеки при транспортуванні по ним енергоносіїв, яка носить приблизний характер та може допомогти у виявленні відповідних тенденцій по зміненню екологічного стану при паспортизації об’єктів будівництва, оцінки їх екологічної безпеки та доцільності подальшої експлуатації. При цьому універсальна інженерно-екологічна шкала стану природно-технічної геосистеми визначається такими показниками, як рівень технічного впливу, об’єм і якість відновлення та часу, який відведено на відновлення стану навколишнього середовища. На основі проведеного аналізу та створеної методики зроблені висновки о необхідності прискорення темпу виконання робіт по реконструкції магістральних нафто- та газових систем. Встановлено, що значна доля робіт при цьому пов’язана з великою кількістю земляних робіт. Для їх ефективного виконання рекомендовано використовувати розроблений механізований комплекс для безперервного та безпід’ємного ремонту лінійної частини магістральних трубопроводів.
- 29 December 2022
- Published by Kharkiv National Automobile and Highway University in Bulletin of Kharkov National Automobile and Highway University
- No. 99,p. 151
Open AccessCurrent technical condition of main pipelines and assessment of environmental safety during trans-portation of energy carriers through them
У статті наведено аналіз технічного стану магістральних трубопроводів та запропоновано ефективні шляхи його покращення. Розроблено методику та шкалу оцінки екологічної безпеки при транспортуванні по ним енергоносіїв, яка носить приблизний характер та може допомогти у виявленні відповідних тенденцій по зміненню екологічного стану при паспортизації об’єктів будівництва, оцінки їх екологічної безпеки та доцільності подальшої експлуатації. При цьому універсальна інженерно-екологічна шкала стану природно-технічної геосистеми визначається такими показниками, як рівень технічного впливу, об’єм і якість відновлення та часу, який відведено на відновлення стану навколишнього середовища. На основі проведеного аналізу та створеної методики зроблені висновки о необхідності прискорення темпу виконання робіт по реконструкції магістральних нафто- та газових систем. Встановлено, що значна доля робіт при цьому пов’язана з великою кількістю земляних робіт. Для їх ефективного виконання рекомендовано використовувати розроблений механізований комплекс для безперервного та безпід’ємного ремонту лінійної частини магістральних трубопроводів.
- Open Access
- 25 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (15) , 7462
Leveling and Minimizing the Load of the Universal Earthmoving Machinery Actuators by Improving the Kinematics of Their Movement When Digging the Soil
This article considers external loads experienced on the rotor actuator of the universal continuous earthmoving machinery when digging wide excavations (ditches) in the soil and the ways to improve its productivity. Under the condition of translational and rotational supply of the soil-developing actuator to the face, the possibility of minimizing and leveling external loads on the actuator by improving the kinematics of its cyclic movement in the face has been experimentally proved. The actuator should move according to the required trajectory, which corresponds to the curve of the lemniscate of Bernoulli. The load of the UEM soil-developing actuator, operating in the mode of digging the soil, and the effectiveness of the suggested method for leveling the external loads have been experimentally assessed on the current physical model of the operating equipment. Leveling and reducing the absolute values of loads on the UEM operating equipment is achieved by improving the actuator trajectory optimization when digging the soil. It implies the additional rotation of the actuator intermediate frame at the end of each half cycle of the operating process. The required duration of the additional rotation of the intermediate frame is functionally dependent on the actual speed of machinery movement. The additional rotation of the intermediate frame, the duration of which is 1.1 s in the mode of maximum productivity, reduces the maximum load of the operating equipment, namely: torque on the rotor axis Mt-by 19% (up to 60 kN m), the components of the main force vector: vertical force-by 9% (up to 40 kN), and lateral force Pl.m-by 32% (up to 58 kN). The obtained results enable to comprehensively assess the maximum load of the UEM operating equipment under the conditions of changing values of the factors on which it depends and to objectively assess the directional stability of the machinery. Aligning the thickness of the shavings cut by the buckets of the rotor actuator in a half-cycle enables to improve the productivity of the universal earthmoving machinery almost twice.
- 25 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (15) , 7462
Open AccessLeveling and Minimizing the Load of the Universal Earthmoving Machinery Actuators by Improving the Kinematics of Their Movement When Digging the Soil
This article considers external loads experienced on the rotor actuator of the universal continuous earthmoving machinery when digging wide excavations (ditches) in the soil and the ways to improve its productivity. Under the condition of translational and rotational supply of the soil-developing actuator to the face, the possibility of minimizing and leveling external loads on the actuator by improving the kinematics of its cyclic movement in the face has been experimentally proved. The actuator should move according to the required trajectory, which corresponds to the curve of the lemniscate of Bernoulli. The load of the UEM soil-developing actuator, operating in the mode of digging the soil, and the effectiveness of the suggested method for leveling the external loads have been experimentally assessed on the current physical model of the operating equipment. Leveling and reducing the absolute values of loads on the UEM operating equipment is achieved by improving the actuator trajectory optimization when digging the soil. It implies the additional rotation of the actuator intermediate frame at the end of each half cycle of the operating process. The required duration of the additional rotation of the intermediate frame is functionally dependent on the actual speed of machinery movement. The additional rotation of the intermediate frame, the duration of which is 1.1 s in the mode of maximum productivity, reduces the maximum load of the operating equipment, namely: torque on the rotor axis Mt-by 19% (up to 60 kN m), the components of the main force vector: vertical force-by 9% (up to 40 kN), and lateral force Pl.m-by 32% (up to 58 kN). The obtained results enable to comprehensively assess the maximum load of the UEM operating equipment under the conditions of changing values of the factors on which it depends and to objectively assess the directional stability of the machinery. Aligning the thickness of the shavings cut by the buckets of the rotor actuator in a half-cycle enables to improve the productivity of the universal earthmoving machinery almost twice.
- Open Access
- 12 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (14) , 7029
Determination of Continuous Earthmoving Machinery Course Stability under the Conditions of Cyclic Lateral Loading
This article presents the results of complex theoretical and experimental studies on creating universal continuous earthmoving machinery operating under non-standard loading conditions, namely, cyclic lateral loading on the actuator during digging. The lateral loading is due to the complex nature of the actuator motion when digging the soil, namely, the longitudinal motion of the machinery, the actuator digging the soil, and the lateral reciprocating motion of the actuator. This allows for variable width excavations in the soil, whose width exceeds the width of the actuator. The key issue of this machinery operation is to provide its course stability. The article considers the choice of soil-developing actuator and shows the developed calculation schemes of external loading on the operating equipment and a base tractor when digging long excavations in the soil. The dependencies to define external forces acting on the actuator when digging the soil and determining the machinery course stability, considering their spatial nature, have been developed and suggested for practical use. The conditions to ensure the stability of the course of universal earthmoving machinery have been formulated and substantiated. The developed method for determining course stability can be used when creating industrial samples of trenching earthmoving machinery.
- 12 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (14) , 7029
Open AccessDetermination of Continuous Earthmoving Machinery Course Stability under the Conditions of Cyclic Lateral Loading
This article presents the results of complex theoretical and experimental studies on creating universal continuous earthmoving machinery operating under non-standard loading conditions, namely, cyclic lateral loading on the actuator during digging. The lateral loading is due to the complex nature of the actuator motion when digging the soil, namely, the longitudinal motion of the machinery, the actuator digging the soil, and the lateral reciprocating motion of the actuator. This allows for variable width excavations in the soil, whose width exceeds the width of the actuator. The key issue of this machinery operation is to provide its course stability. The article considers the choice of soil-developing actuator and shows the developed calculation schemes of external loading on the operating equipment and a base tractor when digging long excavations in the soil. The dependencies to define external forces acting on the actuator when digging the soil and determining the machinery course stability, considering their spatial nature, have been developed and suggested for practical use. The conditions to ensure the stability of the course of universal earthmoving machinery have been formulated and substantiated. The developed method for determining course stability can be used when creating industrial samples of trenching earthmoving machinery.
- Open Access
Optimization of the Motion Algorithm and Reduction of the External Dynamic Load of the Machinery Actuator in Translational and Rotational Modes
This article deals with the theoretical preconditions for creating a high-performance, universal earthmoving vehicle with continuous motion that can create long grooves of different depths and widths in the soil using a single actuator. For this purpose, a new symmetrical rotor actuator was developed, which operates in translational and rotational modes due to the two-level actuator with a double-swivel mounting on the base chassis, instead of the traditional single-swivel mounting. Its use eliminates the possibility of leveling the thickness of the shavings when digging the soil. The rotor-actuator-movement algorithm at the front part was developed from a combination of vehicle movement and cyclic-lateral-actuator movement. In real practice, this means digging up the soil with even shavings. The implementation of the developed algorithm in the physical model of the symmetrical actuator confirmed the possibility of balancing the thickness of the shavings, which are cut by the rotor buckets with up to 10% accuracy. The difference between the results in determining the thickness of the shavings analytically and experimentally is 12% with a confidence interval of 0.95.
Open AccessOptimization of the Motion Algorithm and Reduction of the External Dynamic Load of the Machinery Actuator in Translational and Rotational Modes
This article deals with the theoretical preconditions for creating a high-performance, universal earthmoving vehicle with continuous motion that can create long grooves of different depths and widths in the soil using a single actuator. For this purpose, a new symmetrical rotor actuator was developed, which operates in translational and rotational modes due to the two-level actuator with a double-swivel mounting on the base chassis, instead of the traditional single-swivel mounting. Its use eliminates the possibility of leveling the thickness of the shavings when digging the soil. The rotor-actuator-movement algorithm at the front part was developed from a combination of vehicle movement and cyclic-lateral-actuator movement. In real practice, this means digging up the soil with even shavings. The implementation of the developed algorithm in the physical model of the symmetrical actuator confirmed the possibility of balancing the thickness of the shavings, which are cut by the rotor buckets with up to 10% accuracy. The difference between the results in determining the thickness of the shavings analytically and experimentally is 12% with a confidence interval of 0.95.