Mykhailo Honchar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mykhailo Honchar has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Anatolii Korpach
Department of Engines and Thermal Engineering, Faculty of Automotive and Mechanical Engineering, National Transport University, 1, M. Omelianovycha-Pavlenka Str., 010 10 Kyiv, Ukraine
2 shared publications - Andrii Koval
Faculty of Automotive and Mechanical Engineering, National Transport University, M. Omelianovicha-Pavlenka, 1, 01010 Kiev, Ukraine
2 shared publications - Juraj Gerlici
Department of Transport and Handling Machines, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
2 shared publications - Volodymyr Musiiko
Faculty of Automotive and Mechanical Engineering, National Transport University, M. Omelianovicha-Pavlenka, 1, 01010 Kiev, Ukraine
2 shared publications - Andrej Suchánek
Department of Transport and Handling Machines, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
1 shared publication - Jurii Lazaruk
Faculty of Automotive and Mechanical Engineering, National Transport University, M. Omelianovicha-Pavlenka 1, 01010 Kiev, Ukraine
1 shared publication
Latest Publications
- Open Access
- 25 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (15) , 7462
Leveling and Minimizing the Load of the Universal Earthmoving Machinery Actuators by Improving the Kinematics of Their Movement When Digging the Soil
This article considers external loads experienced on the rotor actuator of the universal continuous earthmoving machinery when digging wide excavations (ditches) in the soil and the ways to improve its productivity. Under the condition of translational and rotational supply of the soil-developing actuator to the face, the possibility of minimizing and leveling external loads on the actuator by improving the kinematics of its cyclic movement in the face has been experimentally proved. The actuator should move according to the required trajectory, which corresponds to the curve of the lemniscate of Bernoulli. The load of the UEM soil-developing actuator, operating in the mode of digging the soil, and the effectiveness of the suggested method for leveling the external loads have been experimentally assessed on the current physical model of the operating equipment. Leveling and reducing the absolute values of loads on the UEM operating equipment is achieved by improving the actuator trajectory optimization when digging the soil. It implies the additional rotation of the actuator intermediate frame at the end of each half cycle of the operating process. The required duration of the additional rotation of the intermediate frame is functionally dependent on the actual speed of machinery movement. The additional rotation of the intermediate frame, the duration of which is 1.1 s in the mode of maximum productivity, reduces the maximum load of the operating equipment, namely: torque on the rotor axis Mt-by 19% (up to 60 kN m), the components of the main force vector: vertical force-by 9% (up to 40 kN), and lateral force Pl.m-by 32% (up to 58 kN). The obtained results enable to comprehensively assess the maximum load of the UEM operating equipment under the conditions of changing values of the factors on which it depends and to objectively assess the directional stability of the machinery. Aligning the thickness of the shavings cut by the buckets of the rotor actuator in a half-cycle enables to improve the productivity of the universal earthmoving machinery almost twice.
- 25 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (15) , 7462
Open AccessLeveling and Minimizing the Load of the Universal Earthmoving Machinery Actuators by Improving the Kinematics of Their Movement When Digging the Soil
This article considers external loads experienced on the rotor actuator of the universal continuous earthmoving machinery when digging wide excavations (ditches) in the soil and the ways to improve its productivity. Under the condition of translational and rotational supply of the soil-developing actuator to the face, the possibility of minimizing and leveling external loads on the actuator by improving the kinematics of its cyclic movement in the face has been experimentally proved. The actuator should move according to the required trajectory, which corresponds to the curve of the lemniscate of Bernoulli. The load of the UEM soil-developing actuator, operating in the mode of digging the soil, and the effectiveness of the suggested method for leveling the external loads have been experimentally assessed on the current physical model of the operating equipment. Leveling and reducing the absolute values of loads on the UEM operating equipment is achieved by improving the actuator trajectory optimization when digging the soil. It implies the additional rotation of the actuator intermediate frame at the end of each half cycle of the operating process. The required duration of the additional rotation of the intermediate frame is functionally dependent on the actual speed of machinery movement. The additional rotation of the intermediate frame, the duration of which is 1.1 s in the mode of maximum productivity, reduces the maximum load of the operating equipment, namely: torque on the rotor axis Mt-by 19% (up to 60 kN m), the components of the main force vector: vertical force-by 9% (up to 40 kN), and lateral force Pl.m-by 32% (up to 58 kN). The obtained results enable to comprehensively assess the maximum load of the UEM operating equipment under the conditions of changing values of the factors on which it depends and to objectively assess the directional stability of the machinery. Aligning the thickness of the shavings cut by the buckets of the rotor actuator in a half-cycle enables to improve the productivity of the universal earthmoving machinery almost twice.
- Open Access
Optimization of the Motion Algorithm and Reduction of the External Dynamic Load of the Machinery Actuator in Translational and Rotational Modes
This article deals with the theoretical preconditions for creating a high-performance, universal earthmoving vehicle with continuous motion that can create long grooves of different depths and widths in the soil using a single actuator. For this purpose, a new symmetrical rotor actuator was developed, which operates in translational and rotational modes due to the two-level actuator with a double-swivel mounting on the base chassis, instead of the traditional single-swivel mounting. Its use eliminates the possibility of leveling the thickness of the shavings when digging the soil. The rotor-actuator-movement algorithm at the front part was developed from a combination of vehicle movement and cyclic-lateral-actuator movement. In real practice, this means digging up the soil with even shavings. The implementation of the developed algorithm in the physical model of the symmetrical actuator confirmed the possibility of balancing the thickness of the shavings, which are cut by the rotor buckets with up to 10% accuracy. The difference between the results in determining the thickness of the shavings analytically and experimentally is 12% with a confidence interval of 0.95.
Open AccessOptimization of the Motion Algorithm and Reduction of the External Dynamic Load of the Machinery Actuator in Translational and Rotational Modes
This article deals with the theoretical preconditions for creating a high-performance, universal earthmoving vehicle with continuous motion that can create long grooves of different depths and widths in the soil using a single actuator. For this purpose, a new symmetrical rotor actuator was developed, which operates in translational and rotational modes due to the two-level actuator with a double-swivel mounting on the base chassis, instead of the traditional single-swivel mounting. Its use eliminates the possibility of leveling the thickness of the shavings when digging the soil. The rotor-actuator-movement algorithm at the front part was developed from a combination of vehicle movement and cyclic-lateral-actuator movement. In real practice, this means digging up the soil with even shavings. The implementation of the developed algorithm in the physical model of the symmetrical actuator confirmed the possibility of balancing the thickness of the shavings, which are cut by the rotor buckets with up to 10% accuracy. The difference between the results in determining the thickness of the shavings analytically and experimentally is 12% with a confidence interval of 0.95.
- Open Access
- 1 November 2020
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 20 (5) , 576-581
The Mathematical Model Refinement of the Continuous Digging Machine and Its Research
- 1 November 2020
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 20 (5) , 576-581
Open AccessThe Mathematical Model Refinement of the Continuous Digging Machine and Its Research