JLJuan Manuel Prado Lazaro

Juan Manuel Prado Lazaro

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Juan Manuel Prado Lazaro has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • COMPARATIVE MECHANICAL SPECTROSCOPY BY COMPUTATIONAL GEOMETRY

    by Brandon Farrera Buenrostro, Israel Aguilera Navarrete, Juan Manuel Prado Lazaro, Hector Javier Vergara Hernandez, Francisco Reyes Calderon

    It is obvious to many that metals produce a characteristic sound when struck. It is well known that for centuries people have subtly struck coins to differentiate between real and counterfeit coins. Unfortunately, when the materials present slight differences such as thermal or mechanical treatments, it is almost impossible for the human ear to differentiate these modifications. Resulta obvio para muchos que los metales al ser impactados producen un sonido característico. Es conocido que durante siglos las personas han golpeado sutilmente las monedas para mediante el sonido diferenciar las verdaderas de las falsas. Lamentablemente cuando los materiales presentan diferencias leves como tratamientos térmicos o mecánicos es casi imposible para el oído humano diferenciar estas modificaciones.

  • HALL-PETCH RELATIONSHIP WITH ULTRAFINE GRAINS IN Zn-22%Al-4%Ag ALLOY IN SEVERE PLASTIC DEFORMATION CONDITIONS

    by Juan Manuel Prado Lazaro, Jose Angel Ramos Banderas, Israel Aguilera Navarrete, Jorge Alejandro Verduzco Martinez, Luis Alejandro Garcia Herrera

    The comparative study of compression and lamination of three groups of specimens in different microstructural conditions of the ZnAlAg alloy and recognized for its superplastic behavior. They are compressed at staggered loads to homogenize and refine the grain size. The X-ray diffraction identified the crystalline phases a, ?, and the intermetallic e. The X-ray diffraction (XRD) shows a position and evolution according to the applied load. The microhardness test carries out in the plastic and packing zone with a diamond indenter and a 50gf load under the ASTM E384 standard. The evolution in the diffraction peaks, microhardness, and applied load found a relationship statistically. The alloy Zn - 22% Al - 4% Ag can be heat treated before a deformation process, allowing more plasticity due to the refinement grain, the distribution of the intermetallic e, and the absence of work hardening allow a softening or a negative slope of the Hall-Petch model. Key Words: Hall-Petch, ZnAlAg alloy, DRX, Superplasticity Mediante el estudio comparativo de compresión y laminación de tres grupos de probetas en diferentes condiciones microestructurales de la aleación ZnAlAg, reconocida por su comportamiento superplástico. Se comprimen a cargas escalonadas con el objetivo de homogenizar y refinar el tamaño de grano. Por medio de difracción de Rayos-X (DRX) se identificaron las fases cristalinas a y ? y el intermetálico e, así como su posicionamiento y su evolución de acuerdo a la carga aplicada. El ensayo de microdureza realizado en la zona plástica y de abarrilamiento con un penetrador de diamante y carga de 50gf bajo la norma ASTM E384. Procesando de manera estadística se encuentra una relación en la microdureza, la evolución en los picos de difracción y la carga aplicada. La aleación Zn-22%Al-4%Ag puede ser tratada térmicamente antes de un proceso de deformación, permitiendo mayor plasticidad debido al refinamiento de grano, la distribución del intermetálico e y la ausencia del endurecimiento por deformación permitiendo una ablandamiento o una pendiente negativa del modelo Hall-Petch. Palabras Clave: Hall-Petch, ZnAlAg alloy, DRX, Superplasticidad

  • EUCLIDEAN CLUSTERIZATION OF PULSE-EXCITED COMPARATIVE MECHANICAL SPECTROSCOPY

    by Brandon Farrera Buenrostro, Israel Aguilera Navarrete, Juan Manuel Prado Lazaro, Hector Javier Vergara Hernandez, Francisco Reyes Calderon

    An alternative methodology is presented to recognize the internal state of a material, which, unlike other methods, it is not necessary to take destructive tests, in addition to the high time and costs involved. The methodology in question is summarized in a technique based on the acoustic-vibrational behaviour of metal alloys, to correlate their acoustic properties and their internal structure. As a case study, a comparison between AISI-SAE 1018 steel and two alloys, one made of aluminum and the other of brass. The specimens are used according to ASTM E1876 for the Impulse Excitation Technique (IET) test. Steel cases were tested in their existing condition and heat treatment according to ASTM E1876 and subjected to a standardized process to compare the acoustic characteristics of the same material with different microstructures. By processing the acoustic response, frequency spectra describe the acoustic behaviour obtained. By processing the acoustic response, frequency spectra describe the vibrational behaviour. The methodology shows results that demonstrate the sensitivity of the test to microstructural changes in metallic materials, demonstrating that the IET test is functional as an alternative method for the identification of materials. Key Words: Mechanical spectroscopy, Impulse excitation, Euclidean clusterization, Non destructive test

  • Zn22Al4Ag ALLOY MICROWIRES CASTING TO RAPID SOLIDIFICATION PROCESS BY ROTATING DRUM

    by Juan Manuel Prado Lazaro, Jose Angel Ramos Banderas, Israel Aguilera Navarrete, Jaime Alejandro Verduzco Martinez, Rocio Maricela Ochoa Palacios

    In this work, the Zn22Al4Ag alloy was synthesized by melting in a muffle furnace.The alloy obtained was characterized by Scanning Electron Microscopy Energy Dispersive Spectroscopy and was analyzed by the X-Ray Diffraction technique, where the crystallinity of the material was verified before and after being processed. Likewise, the Differential Scanning Calorimetry technique was used to obtain the temperatures where phase transformations occurin the alloy. These results were fed to the Termocalc®, software to numerically obtain the phase diagram of the alloy. Subsequently, a section of the ingot was taken to the rapid solidification process by rotating drum. The process variables were manipulated: jet stability, nozzle diameter, distance from the nozzle surface to the cooling medium, the delay time of the molten material in the crucible, speed of the rotating drum and jet angle, until obtaining a microwire with a diameter of ~ 160µm. Finally, it was determined that inadequate control of these parameters can result in powders, flakes or blockage of the crucible outlet. Potentially uses within the micro and nanoworld as an analogy to structural elements and electrical conductors, in addition to its current use as a coating anti-corrosive. Key Words: ZnAlAg alloy, Melt spinning process, Microwire, DSC analysis, Thermodynamic simulation En este trabajo se sintetizó la aleación Zn22Al4Ag mediante fusión en horno de mufla. La aleación obtenida se caracterizó mediante Espectroscopia de Dispersión de Energía por Microscopía Electrónica de Barrido y se analizó mediante la técnica de Difracción de Rayos-X, donde se verificó la cristalinidad del material antes y después de ser procesado. Asimismo, se utilizó la técnica de Calorimetría Diferencial de Barrido para obtener las temperaturas donde se producen las transformaciones de fase en la aleación. Estos resultados se introdujeron en el software Termocalc®, para obtener numéricamente el diagrama de fases de la aleación. Posteriormente, se llevó una sección del lingote al proceso de solidificación rápida mediante tambor rotativo. Se manipularon las variables del proceso: la estabilidad del chorro, el diámetro de la boquilla, la distancia de la superficie de la boquilla al medio de enfriamiento, el tiempo de residencia del material fundido en el crisol, la velocidad del tambor giratorio y el ángulo del chorro, hasta obtener un microalambre con un diámetro de 160µm. Por último, se determinó que un control inadecuado de estos parámetros puede dar lugar a polvos, escamas o al bloqueo de la salida del crisol. Su uso potencial dentro de la escala micro-nano como analogía a elementos estructurales y conductores eléctricos, además de su uso actual como recubrimiento anticorrosivo. Palabras Clave: ZnAlAg alloy, Melt spinning process, Microwire, DSC analysis, Thermodynamic simulation