Dong Ju Shin
Research Subjects
Dong Ju Shin has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Shun Myung Shin
Resources Recycling Research Center, Korea Institute of Geoscience and Mineral Resources (KIGAM), Daejeon, Republic of Korea
7 shared publications Dongseok Lee
Resource Recycling Department, University of Science & Technology(UST), 217 Gajeong-ro, Yuseong-gu, Daejeon 34113, Republic of Korea
6 shared publications- Sung-Ho Joo
Resources Recycling Research Center, Resources Utilization Division Korea
5 shared publications - Ho-Seok Jeon
Korea Institute of Geoscience and Mineral Resources, Daejeon 34132, Korea
3 shared publications - Dongseok Lee
Resources Recovery Research Center, Korea Institute of Geoscience & Mineral Resources (KIGAM), 124 Gwahak-ro, Yuseong-gu, Daejeon 34132, Republic of Korea
1 shared publication Ja-Ryoung Han
1 shared publication
Latest Publications
- Open Access
- 8 October 2026
- Published by Elsevier in SSRN Electronic Journal
A Gravity–Centrifugal Hybrid Separator for Compact, Rapid, and Stable Solvent Extraction: Hydrodynamic Design and Process Validation
Solvent extraction underpins the production of high-purity critical minerals, yet its workhorse equipment has not advanced at a corresponding rate. Most of the industry still relies on conventional mixer-settlers, which separate by gravity alone: low-shear and energy-efficient, but slow and bulky. Centrifugal contactors add speed and compactness by imposing centrifugal fields of hundreds to thousands of g, so that separation rate and mechanical severity—shear, energy, sealing, and safety—remain inextricably coupled.In this study, a compact gravity-centrifugal hybrid separator is developed for rapid and continuous phase separation at substantially reduced rotational speeds (≤ 850 rpm). The separator utilizes two key hydrodynamic features: (i) a tilted yet stable phase interface maintained by synergistic gravity-centrifugal discharge, enabling stable low-speed operation; and (ii) a passive water seal formed by an internal cup-shaped structure that suppresses cross-phase contamination at the outlets. Computational fluid dynamics guided the conceptual design and analyzed interface formation and internal flow structures. A fabricated prototype (500 mL effective volume) demonstrated approximately 99% aqueous phase purity at 800 mL/min in an organic–aqueous system relevant to solvent extraction. Even at flow rates where the gravity-based reference separator lost separation capability, the hybrid separator maintained stable and efficient phase disengagement. These results establish a low-speed hydrodynamic operating for compact gravity–centrifugal hybrid phase separation and demonstrate a practical route for overcoming the throughput limitation of solvent-extraction equipment based solely on gravitational settling or centrifugal separation.
- 8 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA Gravity–Centrifugal Hybrid Separator for Compact, Rapid, and Stable Solvent Extraction: Hydrodynamic Design and Process Validation
Solvent extraction underpins the production of high-purity critical minerals, yet its workhorse equipment has not advanced at a corresponding rate. Most of the industry still relies on conventional mixer-settlers, which separate by gravity alone: low-shear and energy-efficient, but slow and bulky. Centrifugal contactors add speed and compactness by imposing centrifugal fields of hundreds to thousands of g, so that separation rate and mechanical severity—shear, energy, sealing, and safety—remain inextricably coupled.In this study, a compact gravity-centrifugal hybrid separator is developed for rapid and continuous phase separation at substantially reduced rotational speeds (≤ 850 rpm). The separator utilizes two key hydrodynamic features: (i) a tilted yet stable phase interface maintained by synergistic gravity-centrifugal discharge, enabling stable low-speed operation; and (ii) a passive water seal formed by an internal cup-shaped structure that suppresses cross-phase contamination at the outlets. Computational fluid dynamics guided the conceptual design and analyzed interface formation and internal flow structures. A fabricated prototype (500 mL effective volume) demonstrated approximately 99% aqueous phase purity at 800 mL/min in an organic–aqueous system relevant to solvent extraction. Even at flow rates where the gravity-based reference separator lost separation capability, the hybrid separator maintained stable and efficient phase disengagement. These results establish a low-speed hydrodynamic operating for compact gravity–centrifugal hybrid phase separation and demonstrate a practical route for overcoming the throughput limitation of solvent-extraction equipment based solely on gravitational settling or centrifugal separation.
- Open Access
- 31 August 2025
- Published by The Korean Institute of Resources Recycling in Resources Recycling
- Vol. 34 (4) , 64-70
Measurement of Oxygen Potential in Molten Oxides and Its Application to Viscosity Studies
- 31 August 2025
- Published by The Korean Institute of Resources Recycling in Resources Recycling
- Vol. 34 (4) , 64-70
Open AccessMeasurement of Oxygen Potential in Molten Oxides and Its Application to Viscosity Studies
- Open Access
- 28 February 2023
- Published by The Korean Institute of Resources Recycling in Resources Recycling
- Vol. 32 (1) , 42-49
A Study on the Recovery of Lithium from Secondary Resources of Ceramic Glass Containing Li-Al-Si by Ca-based Salt Roasting and Water Leaching Process
The glass ceramic secondary resource containing Li-Al-Si is used in inductor, fireproof glass, and transparent cookware and accounts for 14% of the total consumption of Li, which is the second most widely used after Li-ion batteries. Therefore, new Li resources should be explored when the demand for Li is exploding, and extensive research on Li recovery is needed. Herein, we recovered Li from fireproof Li-Al-Si glass ceramic, which is a new secondary resource containing Li. The fireproof glass among all Li-Al-Si glass ceramics was used as raw material that contained 1.5% Li, 9.4% Al, and 28.9% Si. The process for recovering •
- 28 February 2023
- Published by The Korean Institute of Resources Recycling in Resources Recycling
- Vol. 32 (1) , 42-49
Open AccessA Study on the Recovery of Lithium from Secondary Resources of Ceramic Glass Containing Li-Al-Si by Ca-based Salt Roasting and Water Leaching Process
The glass ceramic secondary resource containing Li-Al-Si is used in inductor, fireproof glass, and transparent cookware and accounts for 14% of the total consumption of Li, which is the second most widely used after Li-ion batteries. Therefore, new Li resources should be explored when the demand for Li is exploding, and extensive research on Li recovery is needed. Herein, we recovered Li from fireproof Li-Al-Si glass ceramic, which is a new secondary resource containing Li. The fireproof glass among all Li-Al-Si glass ceramics was used as raw material that contained 1.5% Li, 9.4% Al, and 28.9% Si. The process for recovering •
- Open Access
- 28 February 2023
- Published by The Korean Institute of Resources Recycling in Resources Recycling
- Vol. 32 (1) , 33-41
Study for Manufacturing of Zinc Sulfate from Electric Arc Furnace Dust by Hydrometallrugical Process
Herein, we selectively recovered Zn and produced ZnSO 4 from electric arc furnace dust using a hydrometallurgical process. The analysis of the properties of the electric arc furnace dust revealed that the Fe content (9.9%) was relatively low while the Mn content (19%) was high as compared to the composition of general dust. Therefore, an appropriate hydrometallurgical process was designed based on the properties of the raw materials. In the leaching process involving the use of 1.6 M sulfuric acid and 20% solid-liquid ratio at 60℃ for 1 h, 85% of the Zn and Mn got dissolved while the Fe was not leached. To selectively recover Zn, a solvent extraction process using D2EHPA as the extractant was chosen, and 99% of the Zn was extracted using 0.8 M D2EHPA with 32% saponification and an O/A ratio of 2 using counter-current 3-stage extraction. Mn was entirely scrubbed with an aqueous sulfuric acid solution of pH 1.5. Finally, Zn was concentrated and stripped using 1.5 M sulfuric acid at an O/A ratio of 4 using counter-current 4-stage stripping. The stripping solution contained 40 g/L of Zn, and 99.9% of ZnSO 4 •H 2 O was obtained by vacuum distillation.
- 28 February 2023
- Published by The Korean Institute of Resources Recycling in Resources Recycling
- Vol. 32 (1) , 33-41
Open AccessStudy for Manufacturing of Zinc Sulfate from Electric Arc Furnace Dust by Hydrometallrugical Process
Herein, we selectively recovered Zn and produced ZnSO 4 from electric arc furnace dust using a hydrometallurgical process. The analysis of the properties of the electric arc furnace dust revealed that the Fe content (9.9%) was relatively low while the Mn content (19%) was high as compared to the composition of general dust. Therefore, an appropriate hydrometallurgical process was designed based on the properties of the raw materials. In the leaching process involving the use of 1.6 M sulfuric acid and 20% solid-liquid ratio at 60℃ for 1 h, 85% of the Zn and Mn got dissolved while the Fe was not leached. To selectively recover Zn, a solvent extraction process using D2EHPA as the extractant was chosen, and 99% of the Zn was extracted using 0.8 M D2EHPA with 32% saponification and an O/A ratio of 2 using counter-current 3-stage extraction. Mn was entirely scrubbed with an aqueous sulfuric acid solution of pH 1.5. Finally, Zn was concentrated and stripped using 1.5 M sulfuric acid at an O/A ratio of 4 using counter-current 4-stage stripping. The stripping solution contained 40 g/L of Zn, and 99.9% of ZnSO 4 •H 2 O was obtained by vacuum distillation.
- Open Access
- 28 February 2022
- Published by The Korean Institute of Resources Recycling in Resources Recycling
- Vol. 31 (1) , 65-77
Leaching Behavior of Vanadium and Possibility of Recovery of Valuable Metals from VTM Concentrate by Sulfuric Acid Leaching
- 28 February 2022
- Published by The Korean Institute of Resources Recycling in Resources Recycling
- Vol. 31 (1) , 65-77
Open AccessLeaching Behavior of Vanadium and Possibility of Recovery of Valuable Metals from VTM Concentrate by Sulfuric Acid Leaching
- Open Access
- 17 January 2022
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 100 (12) , 3760-3767
Precipitation of lithium phosphate from lithium solution by using sodium phosphate
Lithium was studied to precipitate into Li3PO4 by adding Na3PO4 under various experimental conditions such as initial lithium concentration of the solution, initial pH of the solution, temperature, and the mol equivalent ratio of Na3PO4. The precipitation mechanism of Li3PO4 was investigated with the change of pH value of the solution over time. The precipitation efficiency of Li3PO4 was 95.4% in the condition of the mol equivalent ratio of Na3PO4 of 1, initial Li concentration of 7 g/L, initial pH of 9.5, and at 90°C. When Na3PO4 was added three times, divided in the mol equivalent ratio of 1 via the hydrolysis reaction of PO43−, which inhibits the Li3PO4 precipitation reaction, an excellent precipitation efficiency of 98.4% was obtained. Co‐precipitated Na2HPO4 with Li3PO4 was washed by distilled water in the condition of solid/liquid ratio of 10% and at 90°C. The purity of the final Li3PO4 product was found to be 99.1%.
- 17 January 2022
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 100 (12) , 3760-3767
Open AccessPrecipitation of lithium phosphate from lithium solution by using sodium phosphate
Lithium was studied to precipitate into Li3PO4 by adding Na3PO4 under various experimental conditions such as initial lithium concentration of the solution, initial pH of the solution, temperature, and the mol equivalent ratio of Na3PO4. The precipitation mechanism of Li3PO4 was investigated with the change of pH value of the solution over time. The precipitation efficiency of Li3PO4 was 95.4% in the condition of the mol equivalent ratio of Na3PO4 of 1, initial Li concentration of 7 g/L, initial pH of 9.5, and at 90°C. When Na3PO4 was added three times, divided in the mol equivalent ratio of 1 via the hydrolysis reaction of PO43−, which inhibits the Li3PO4 precipitation reaction, an excellent precipitation efficiency of 98.4% was obtained. Co‐precipitated Na2HPO4 with Li3PO4 was washed by distilled water in the condition of solid/liquid ratio of 10% and at 90°C. The purity of the final Li3PO4 product was found to be 99.1%.
- 20 December 2021
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 24 (2) , 790-799
Recovery of vanadium and cesium from spent sulfuric acid catalysts by a hydrometallurgical process
An environmentally friendly hydrometallurgical process was developed to recover vanadium and cesium selectively from spent sulfuric acid catalysts, and it has high recovery efficiency and economic advantages.
- 20 December 2021
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 24 (2) , 790-799
Recovery of vanadium and cesium from spent sulfuric acid catalysts by a hydrometallurgical process
An environmentally friendly hydrometallurgical process was developed to recover vanadium and cesium selectively from spent sulfuric acid catalysts, and it has high recovery efficiency and economic advantages.
- Open Access
- 31 October 2021
- Published by The Korean Institute of Resources Recycling in Resources Recycling
- Vol. 30 (5) , 57-66
Study for Seperation Process of Copper from the Low-grade Copper Ore by Hydrometallrugical Process
- 31 October 2021
- Published by The Korean Institute of Resources Recycling in Resources Recycling
- Vol. 30 (5) , 57-66
Open AccessStudy for Seperation Process of Copper from the Low-grade Copper Ore by Hydrometallrugical Process
- Open Access
- 31 August 2021
- Published by The Korean Institute of Resources Recycling in Resources Recycling
- Vol. 30 (4) , 27-34
Vanadium Leaching Behavior from Domestic Vanadium Bearing Titanomagnetite Ore through CaO Roasting
- 31 August 2021
- Published by The Korean Institute of Resources Recycling in Resources Recycling
- Vol. 30 (4) , 27-34
Open AccessVanadium Leaching Behavior from Domestic Vanadium Bearing Titanomagnetite Ore through CaO Roasting