Liang Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Liang Zhang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Kun Sun
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an, China
2 shared publications - Longlong Yang
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an 710049, China
2 shared publications - Keru Chen
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication - Pujie Zhu
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication - Weixiang Peng
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication - Xuejie Li
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication
Latest Publications
- Open Access
- 24 November 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (23) , 4179
The Influence of Carbides on Atomic-Scale Mechanical Properties of Carbon Steel: A Molecular Dynamics Study
Pearlite is an important structure in carbon steel; however, the influence mechanism of carbides in pearlite on its mechanical properties and microstructure evolution has not yet been fully elucidated. In this work, a ferrite–carbide composite model with various carbide types was constructed to investigate the influence of carbide types via a uniaxial compression deformation using classical molecular dynamics simulations. It was found that the carbide type had little effect on the compressive elastic modulus, but a more obvious effect on the yield strain, yield stress, and flow stress. The maximum compressive elastic modulus was in the Fe2C model, with 300.32 GPa, while the minimum was found in the Fe4C model at 285.16 GPa; the error was 5.32%. There were significant differences in the yield stress, yield strain, and flow stress of the ferrite–carbide model according to the stress–strain curve. Secondly, the type of carbide used affected its elastic constant, especially the bulk modulus and Cauchy pressure. The maximum bulk modulus of the Fe4C model was 199.01 GPa, the minimum value of the Fe3C model was 146.03 GPa, and the difference was 52.98 GPa. The Cauchy pressure calculation results were consistent with the yield strain trend. Additionally, the effective elastic moduli of the composite system were used to verify the accuracy of the calculation results of this work. Thirdly, ferrite–carbide interfaces could act as a resource for dislocation emission. The initial stacking fault forms at ferrite–carbide interfaces and expands into ferrite. The dislocation type and segment in the ferrite–carbide model were significantly different due to the type of carbide used.
- 24 November 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (23) , 4179
Open AccessThe Influence of Carbides on Atomic-Scale Mechanical Properties of Carbon Steel: A Molecular Dynamics Study
Pearlite is an important structure in carbon steel; however, the influence mechanism of carbides in pearlite on its mechanical properties and microstructure evolution has not yet been fully elucidated. In this work, a ferrite–carbide composite model with various carbide types was constructed to investigate the influence of carbide types via a uniaxial compression deformation using classical molecular dynamics simulations. It was found that the carbide type had little effect on the compressive elastic modulus, but a more obvious effect on the yield strain, yield stress, and flow stress. The maximum compressive elastic modulus was in the Fe2C model, with 300.32 GPa, while the minimum was found in the Fe4C model at 285.16 GPa; the error was 5.32%. There were significant differences in the yield stress, yield strain, and flow stress of the ferrite–carbide model according to the stress–strain curve. Secondly, the type of carbide used affected its elastic constant, especially the bulk modulus and Cauchy pressure. The maximum bulk modulus of the Fe4C model was 199.01 GPa, the minimum value of the Fe3C model was 146.03 GPa, and the difference was 52.98 GPa. The Cauchy pressure calculation results were consistent with the yield strain trend. Additionally, the effective elastic moduli of the composite system were used to verify the accuracy of the calculation results of this work. Thirdly, ferrite–carbide interfaces could act as a resource for dislocation emission. The initial stacking fault forms at ferrite–carbide interfaces and expands into ferrite. The dislocation type and segment in the ferrite–carbide model were significantly different due to the type of carbide used.
- Open Access
Effects of Grain Boundary Angles on Initial Deformation of 304 Austenitic Stainless Steel under Nanoindentation: A Molecular Dynamics Simulation
Nitrogen-containing 0Cr19Ni10 (304 NG) austenitic stainless steel plays a significant role in Generation IV reactor pressure vessels. The structure and properties of 304 NG are heavily influenced by the grain boundaries (GBs), especially the initial mechanical response and dislocation evolutions. Hence, in this paper, we carried out molecular dynamics (MD) simulations to investigate the effects of the GB angles on the initial deformation of 304 models under nanoindentation. It is found that the GB angle has great effects on the mechanical properties of 304 NG. With the GB angles changing from 90° to 150°, the values of Young’s modulus and maximum shear stress first decrease and then increase due to decreasing of the interaction among the GBs and the grain interiors (GIs) and the smoother shape of GBs. The hardening region slope decreases rapidly result from the GB angles changing the grain size on the both sides, which fully fits the Hall–Petch relationship. After the dislocations reaching the GBs along the slip system, the dislocation piles-up on the GBs at first, and then GBs serve as a source of dislocation and emit dislocation to free surface with the depth of nanoindentation increasing. This work provides a better understanding on the angle effects of GBs in materials.
Open AccessEffects of Grain Boundary Angles on Initial Deformation of 304 Austenitic Stainless Steel under Nanoindentation: A Molecular Dynamics Simulation
Nitrogen-containing 0Cr19Ni10 (304 NG) austenitic stainless steel plays a significant role in Generation IV reactor pressure vessels. The structure and properties of 304 NG are heavily influenced by the grain boundaries (GBs), especially the initial mechanical response and dislocation evolutions. Hence, in this paper, we carried out molecular dynamics (MD) simulations to investigate the effects of the GB angles on the initial deformation of 304 models under nanoindentation. It is found that the GB angle has great effects on the mechanical properties of 304 NG. With the GB angles changing from 90° to 150°, the values of Young’s modulus and maximum shear stress first decrease and then increase due to decreasing of the interaction among the GBs and the grain interiors (GIs) and the smoother shape of GBs. The hardening region slope decreases rapidly result from the GB angles changing the grain size on the both sides, which fully fits the Hall–Petch relationship. After the dislocations reaching the GBs along the slip system, the dislocation piles-up on the GBs at first, and then GBs serve as a source of dislocation and emit dislocation to free surface with the depth of nanoindentation increasing. This work provides a better understanding on the angle effects of GBs in materials.