LYLonglong Yang

Longlong Yang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Longlong Yang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of Void Defects on the Indentation Behavior of Ni/Ni3Al Crystal

    by Longlong Yang, Kun Sun, Huaying Wu

    Inconel 718 (IN 718) superalloys are widely used as engineering materials owing to their superior mechanical performance. And voids are unavoidable defects in IN 718 superalloy preparation, which dramatically affect the mechanical properties of IN 718 superalloys. In this work, the effects of void radius, distance from the top of the void to the substrate surface, and substrate temperature on the mechanical properties of the Ni/Ni3Al crystal are systematically investigated. It is shown that voids affect the formation of stair-rod dislocations and Shockley dislocations in the substrate, which in turn determines the mechanical properties. Thus, with the increase in void radius, Young’s modulus and hardness gradually decrease. With the increase in void distance, Young’s modulus and hardness increase and finally tend to be stable. In addition, the increase in substrate temperature leads to the interphase boundary becoming irregular and increases the defects in the γ and γ″ phases. As a result, Young’s modulus and hardness of the substrate decrease. This work aims to provide a guideline for investigating the indentation properties of Ni-based superalloys using MD.


  • Open Access

    The Influence of Carbides on Atomic-Scale Mechanical Properties of Carbon Steel: A Molecular Dynamics Study

    by Liang Zhang, Longlong Yang, Kun Sun, Pujie Zhu, Keru Chen

    Pearlite is an important structure in carbon steel; however, the influence mechanism of carbides in pearlite on its mechanical properties and microstructure evolution has not yet been fully elucidated. In this work, a ferrite–carbide composite model with various carbide types was constructed to investigate the influence of carbide types via a uniaxial compression deformation using classical molecular dynamics simulations. It was found that the carbide type had little effect on the compressive elastic modulus, but a more obvious effect on the yield strain, yield stress, and flow stress. The maximum compressive elastic modulus was in the Fe2C model, with 300.32 GPa, while the minimum was found in the Fe4C model at 285.16 GPa; the error was 5.32%. There were significant differences in the yield stress, yield strain, and flow stress of the ferrite–carbide model according to the stress–strain curve. Secondly, the type of carbide used affected its elastic constant, especially the bulk modulus and Cauchy pressure. The maximum bulk modulus of the Fe4C model was 199.01 GPa, the minimum value of the Fe3C model was 146.03 GPa, and the difference was 52.98 GPa. The Cauchy pressure calculation results were consistent with the yield strain trend. Additionally, the effective elastic moduli of the composite system were used to verify the accuracy of the calculation results of this work. Thirdly, ferrite–carbide interfaces could act as a resource for dislocation emission. The initial stacking fault forms at ferrite–carbide interfaces and expands into ferrite. The dislocation type and segment in the ferrite–carbide model were significantly different due to the type of carbide used.


  • Open Access

    Effects of Grain Boundary Angles on Initial Deformation of 304 Austenitic Stainless Steel under Nanoindentation: A Molecular Dynamics Simulation

    by Longlong Yang, Kun Sun, Weixiang Peng, Xuejie Li, Liang Zhang

    Nitrogen-containing 0Cr19Ni10 (304 NG) austenitic stainless steel plays a significant role in Generation IV reactor pressure vessels. The structure and properties of 304 NG are heavily influenced by the grain boundaries (GBs), especially the initial mechanical response and dislocation evolutions. Hence, in this paper, we carried out molecular dynamics (MD) simulations to investigate the effects of the GB angles on the initial deformation of 304 models under nanoindentation. It is found that the GB angle has great effects on the mechanical properties of 304 NG. With the GB angles changing from 90° to 150°, the values of Young’s modulus and maximum shear stress first decrease and then increase due to decreasing of the interaction among the GBs and the grain interiors (GIs) and the smoother shape of GBs. The hardening region slope decreases rapidly result from the GB angles changing the grain size on the both sides, which fully fits the Hall–Petch relationship. After the dislocations reaching the GBs along the slip system, the dislocation piles-up on the GBs at first, and then GBs serve as a source of dislocation and emit dislocation to free surface with the depth of nanoindentation increasing. This work provides a better understanding on the angle effects of GBs in materials.


  • Open Access

    Friction and Wear Characteristics of 18Ni(300) Maraging Steel under High-Speed Dry Sliding Conditions

    by Kun Sun, Weixiang Peng, Binghui Wei, Longlong Yang, Liang Fang

    18Ni(300) maraging steel, which has exceptional strength and toughness, is used in the field of aviation and aerospace. In this paper, using a high-speed tribo-tester, tribological behaviors of 18Ni(300) maraging steel were investigated under high-speed dry sliding conditions. Morphology of the worn surfaces and the debris was analyzed by scanning electron microscope, and the oxides of worn surfaces caused by friction heat were detected by X-ray diffraction. The experiment results reveal that the friction coefficient of frictional pairs declines with increasing load and speed. With the speed and load increasing, oxides of the worn surfaces of 18Ni(300) maraging steel change from FeO to Fe3O4 and the wear mechanism converts from adhesive wear into severe oxidative or extrusion wear.


  • Open Access

    Effect of SLM Processing Parameters on Microstructures and Mechanical Properties of Al0.5CoCrFeNi High Entropy Alloys

    by Kun Sun, Weixiang Peng, Longlong Yang, Liang Fang

    Selective laser melting (SLM) to fabricate Al0.5CoCrFeNi high entropy alloys with pre-mixed powders was studied in this paper. The influences of process parameters including laser power, scanning speed, and hatch spacing on the relative density of high-entropy alloys (HEAs) were investigated. A relative density of 99.92% can be achieved by optimizing the SLM process parameters with laser power 320 W, scanning speed 800 mm/s, and hatch spacing of 60 μm, respectively. Moreover, the microstructure of the HEAs was also studied using scanning electron microscopy (SEM) and x-ray diffraction (XRD). It was found that the microstructure of the HEAs was only composed of face-centered cubic and body-centered cubic phases, without complex intermetallic compounds. The mechanical properties of the HEAs were also characterized. At ambient temperature, the alloys had a high yield strength of about 609 MPa, tensile strength about 878 MPa, and hardness about 270 HV. Through a comparison with the corresponding alloys fabricated by vacuum induction melting, it can be concluded that the high entropy alloys fabricated by SLM had fine microstructures and improved mechanical properties.