Лазизжон Неъматович Атакулов
Лазизжон Неъматович Атакулов has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Ойбек Мухамматкулович Курбонов
Доцент (PhD), Докторант (DSc) Навоийского государственного горно-технологического университета, Навоий, Узбекистан
3 shared publications - Guldana Akanova
Kazakh National Research Technical University named after K.I. Satpayev
2 shared publications Мафтуна Давроновна Сафарова
Докторант (PhD) Навоийского государственного горно-технологического университета, Навоий, Узбекистан
2 shared publications- D. E. Kramsakov
Kazakh National Research Technical University named after K.I. Satpayev
1 shared publication - Laila Sagatova
Kazakh National Research Technical University named after K.I.Satpayev
1 shared publication - Muhammad Istamov1 shared publication
Latest Publications
- Open Access
- 31 July 2025
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 7(243),p. 47-54
INVESTIGATION OF VELOCITY MODES OF LIQUID FLOWS AROUND ELECTRIC MOTORS OF SUBMERSIBLE PUMPS
Water supply and wastewater disposal are among the industries with intensive use of pumping equipment, the share of electricity consumed by pumps is more than 50% of the total energy consumption. One of the reasons for the decrease in technical and economic indicators of submersible pumping units is the failure of pump motors due to overheating during their operation. In this regard, the substantiation and development of methods of research and calculation of fl uid fl ow parameters around the pump motor, is an urgent scientifi c and practical task. The aim of the work is to provide conditions of stable cooling of pump motors at which the temperature of electric motor windings will be within permissible limits. To achieve this goal, the task of developing a methodology for modelling the turbulent vortex fl uid fl ow along the electric motor of a submersible pump is solved Сумен жабдықтау және су бұру сорғы жабдықтарын қарқынды пайдаланатын өнеркәсіп салаларына жатады, сорғылар тұтынатын электр энергиясының үлесі жалпы энергия тұтынудың 50%-дан астамын құрайды. Суасты сорғы қондырғылары жұмысының техникалық-экономикалық көрсеткіштерінің төмендеуінің себептерінің бірі сорғылардың Электр қозғалтқыштарының жұмыс процесінде қызып кетуіне байланысты істен шығуы болып табылады. Осыған байланысты сорғы қозғалтқышының айналасындағы сұйықтық ағынының параметрлерін зерттеу және есептеу әдістерін негіздеу және дамыту өзекті ғылыми және практикалық міндет болып табылады. Мақсатқа жету үшін суасты сорғысының электр қозғалтқышы бойымен сұйықтықтың турбулентті құйынды ағынын модельдеу әдісін әзірлеу міндеті шешілуде Водоснабжение и водоотведение относятся к отраслям промышленности с интенсивным использованием насосного оборудования, доля электроэнергии, потребляемой насосами, составляет более 50% от общего энергопотребления. Одной из причин снижения технико-экономических показателей работы погружных насосных установок является выход из строя электродвигателей насосов из-за перегрева в процессе их работы. В этой связи обоснование и развитие методов исследования и расчета параметров потока жидкости вокруг двигателя насоса является актуальной научной и практической задачей. Для достижения поставленной цели решается задача разработки методики моделирования турбулентного вихревого потока жидкости вдоль электродвигателя погружного насоса
- 31 July 2025
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 7(243),p. 47-54
Open AccessINVESTIGATION OF VELOCITY MODES OF LIQUID FLOWS AROUND ELECTRIC MOTORS OF SUBMERSIBLE PUMPS
Water supply and wastewater disposal are among the industries with intensive use of pumping equipment, the share of electricity consumed by pumps is more than 50% of the total energy consumption. One of the reasons for the decrease in technical and economic indicators of submersible pumping units is the failure of pump motors due to overheating during their operation. In this regard, the substantiation and development of methods of research and calculation of fl uid fl ow parameters around the pump motor, is an urgent scientifi c and practical task. The aim of the work is to provide conditions of stable cooling of pump motors at which the temperature of electric motor windings will be within permissible limits. To achieve this goal, the task of developing a methodology for modelling the turbulent vortex fl uid fl ow along the electric motor of a submersible pump is solved Сумен жабдықтау және су бұру сорғы жабдықтарын қарқынды пайдаланатын өнеркәсіп салаларына жатады, сорғылар тұтынатын электр энергиясының үлесі жалпы энергия тұтынудың 50%-дан астамын құрайды. Суасты сорғы қондырғылары жұмысының техникалық-экономикалық көрсеткіштерінің төмендеуінің себептерінің бірі сорғылардың Электр қозғалтқыштарының жұмыс процесінде қызып кетуіне байланысты істен шығуы болып табылады. Осыған байланысты сорғы қозғалтқышының айналасындағы сұйықтық ағынының параметрлерін зерттеу және есептеу әдістерін негіздеу және дамыту өзекті ғылыми және практикалық міндет болып табылады. Мақсатқа жету үшін суасты сорғысының электр қозғалтқышы бойымен сұйықтықтың турбулентті құйынды ағынын модельдеу әдісін әзірлеу міндеті шешілуде Водоснабжение и водоотведение относятся к отраслям промышленности с интенсивным использованием насосного оборудования, доля электроэнергии, потребляемой насосами, составляет более 50% от общего энергопотребления. Одной из причин снижения технико-экономических показателей работы погружных насосных установок является выход из строя электродвигателей насосов из-за перегрева в процессе их работы. В этой связи обоснование и развитие методов исследования и расчета параметров потока жидкости вокруг двигателя насоса является актуальной научной и практической задачей. Для достижения поставленной цели решается задача разработки методики моделирования турбулентного вихревого потока жидкости вдоль электродвигателя погружного насоса
- Open Access
- 19 May 2025
- Published by Karshi State Technical University in Sanoatda raqamli texnologiyalar
- Vol. 3 (2) , 60-65
ИССЛЕДОВАНИЕ ВЛИЯНИЯ ПЕСКОПРОЯВЛЕНИЯ НА РЕЖИМЫ РАБОТЫ НАСОСНОГО ОБОРУДОВАНИЯ В УСЛОВИЯХ КЫЗИЛКУМСКОГО РЕГИОНА
The article presents an analysis of technological methods aimed at studying the consequences of sand manifestations in wells in the Kyzylkum region. The main causes of sand manifestations and their impact on pump operation, including damage to working parts, decrease in pressure characteristics, and increase in repair frequency, are considered.
- 19 May 2025
- Published by Karshi State Technical University in Sanoatda raqamli texnologiyalar
- Vol. 3 (2) , 60-65
Open AccessИССЛЕДОВАНИЕ ВЛИЯНИЯ ПЕСКОПРОЯВЛЕНИЯ НА РЕЖИМЫ РАБОТЫ НАСОСНОГО ОБОРУДОВАНИЯ В УСЛОВИЯХ КЫЗИЛКУМСКОГО РЕГИОНА
The article presents an analysis of technological methods aimed at studying the consequences of sand manifestations in wells in the Kyzylkum region. The main causes of sand manifestations and their impact on pump operation, including damage to working parts, decrease in pressure characteristics, and increase in repair frequency, are considered.
- Open Access
- 19 May 2025
- Published by Karshi State Technical University in Sanoatda raqamli texnologiyalar
- Vol. 3 (2) , 66-72
ИССЛЕДОВАНИЕ ОСНОВНЫХ ПРИЧИН ОТКАЗОВ И РАСЧЁТ СКОРОСТИ ОБТЕКАНИЯ ДВИГАТЕЛЯ ПОГРУЖНОГО НАСОСА
The article studies common causes of submersible pumps failure. The influence of formation temperature on the operation of submersible pumps is studied. Negative factors appearing, at increase of temperature of electric motor of submersible pump are studied. The influence of high temperature on the material of submersible pump has been studied. The effect and methods of installation of cooling casing for submersible pump are studied. Calculated the flow velocity passing near the electric motor part of the submersible pump. Determined the optimum diameter of the cooling jacket for the submersible pump.
- 19 May 2025
- Published by Karshi State Technical University in Sanoatda raqamli texnologiyalar
- Vol. 3 (2) , 66-72
Open AccessИССЛЕДОВАНИЕ ОСНОВНЫХ ПРИЧИН ОТКАЗОВ И РАСЧЁТ СКОРОСТИ ОБТЕКАНИЯ ДВИГАТЕЛЯ ПОГРУЖНОГО НАСОСА
The article studies common causes of submersible pumps failure. The influence of formation temperature on the operation of submersible pumps is studied. Negative factors appearing, at increase of temperature of electric motor of submersible pump are studied. The influence of high temperature on the material of submersible pump has been studied. The effect and methods of installation of cooling casing for submersible pump are studied. Calculated the flow velocity passing near the electric motor part of the submersible pump. Determined the optimum diameter of the cooling jacket for the submersible pump.
- Open Access
- 6 May 2025
- Published by Karshi State Technical University in Sanoatda raqamli texnologiyalar
- Vol. 3 (2) , 81-90
ОБЗОР И АНАЛИЗ МЕТОДОВ РЕМОНТА КРУПНОГАБАРИТНЫХ ШИН КАРЬЕРНЫХ АВТОСАМОСВАЛОВ
In the context of the intensification of open-pit mining and the growth of the quarry machinery fleet, the issues of efficient use and maintenance of oversized and ultra-large tires are becoming particularly relevant. This article is devoted to the analysis of the causes of tire wear of quarry dump trucks and the consideration of the hot vulcanization method as the main method of their restoration. It was established that the greatest risk of damage falls on the sides of the tread and tire, and the nature of the defects is diverse and often combined. The hot vulcanization method, in strict accordance with technological regulations, ensures the restoration of the mechanical properties of tires and a significant increase in their service life. The main stages of restoration are considered, including preparation, cleaning, application of restoration materials, heat treatment, and cosmetic restoration. It was noted that the process is labor-intensive and requires further optimization, including the automation and improvement of technological solutions. In addition, in order to increase the wear resistance of tires and wheels, it is proposed to consider the possibility of implementing design changes in them themselves. The obtained results can be useful in the development of maintenance regulations and the improvement of quarry equipment repair systems.
- 6 May 2025
- Published by Karshi State Technical University in Sanoatda raqamli texnologiyalar
- Vol. 3 (2) , 81-90
Open AccessОБЗОР И АНАЛИЗ МЕТОДОВ РЕМОНТА КРУПНОГАБАРИТНЫХ ШИН КАРЬЕРНЫХ АВТОСАМОСВАЛОВ
In the context of the intensification of open-pit mining and the growth of the quarry machinery fleet, the issues of efficient use and maintenance of oversized and ultra-large tires are becoming particularly relevant. This article is devoted to the analysis of the causes of tire wear of quarry dump trucks and the consideration of the hot vulcanization method as the main method of their restoration. It was established that the greatest risk of damage falls on the sides of the tread and tire, and the nature of the defects is diverse and often combined. The hot vulcanization method, in strict accordance with technological regulations, ensures the restoration of the mechanical properties of tires and a significant increase in their service life. The main stages of restoration are considered, including preparation, cleaning, application of restoration materials, heat treatment, and cosmetic restoration. It was noted that the process is labor-intensive and requires further optimization, including the automation and improvement of technological solutions. In addition, in order to increase the wear resistance of tires and wheels, it is proposed to consider the possibility of implementing design changes in them themselves. The obtained results can be useful in the development of maintenance regulations and the improvement of quarry equipment repair systems.
- 1 December 2021
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 15 (4) , 75-83
Choosing the flow part geometric shape of the dredge pumps for viscous fluids
Purpose. Search for the possibility of increasing the efficiency of dredge pumps for viscous fluids by determining the rational values of the blade-outlet inclination angles in the pump impellers. Methods. During the research, the following is used: theoretical studies of the structure of the viscous fluids flowing through the flow part of dredge pumps; the method of three-dimensional software-simulation modeling of hydrodynamic processes using the Ansys software package; the methods of rational experiment planning for selecting the values of the number of points in the computational grid when optimizing the geometric parameters of the dredge pump impellers; methods of mathematical statistics and correlation analysis. Findings. It has been proven that the main reason for the failure of the flow part components in the dredge pumps is the manifestation of the influence of cavitation processes, which can be eliminated by changing the blade-outlet inclination angles in the pump impellers. A software-simulation complex for the automated design of the flow parts in the dredge pumps has been developed based on the use of optimization algorithms and computational fluid dynamics methods, which makes it possible to design dredge pumps with optimal characteristics that ensure their efficient operation with maximum efficiency values. It has been determined that one of the main factors influencing the head developed by dredge pumps and the efficiency value is the blade-outlet inclination angle in the pump impellers. Originality. Scientific novelty is in the scientific substantiation and development of a simulation-mathematical method for calculating the geometric parameters of the flow part in dredge pumps for viscous fluids at the design stage. Practical implications. The developed method for determining the rational blade-outlet inclination angles of the impellers in the dredge pumps for viscous fluids can be recommended to scientific-research and industrial organizations for use in the improvement, design and operation of the dredge pumps.
- 1 December 2021
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 15 (4) , 75-83
Choosing the flow part geometric shape of the dredge pumps for viscous fluids
Purpose. Search for the possibility of increasing the efficiency of dredge pumps for viscous fluids by determining the rational values of the blade-outlet inclination angles in the pump impellers. Methods. During the research, the following is used: theoretical studies of the structure of the viscous fluids flowing through the flow part of dredge pumps; the method of three-dimensional software-simulation modeling of hydrodynamic processes using the Ansys software package; the methods of rational experiment planning for selecting the values of the number of points in the computational grid when optimizing the geometric parameters of the dredge pump impellers; methods of mathematical statistics and correlation analysis. Findings. It has been proven that the main reason for the failure of the flow part components in the dredge pumps is the manifestation of the influence of cavitation processes, which can be eliminated by changing the blade-outlet inclination angles in the pump impellers. A software-simulation complex for the automated design of the flow parts in the dredge pumps has been developed based on the use of optimization algorithms and computational fluid dynamics methods, which makes it possible to design dredge pumps with optimal characteristics that ensure their efficient operation with maximum efficiency values. It has been determined that one of the main factors influencing the head developed by dredge pumps and the efficiency value is the blade-outlet inclination angle in the pump impellers. Originality. Scientific novelty is in the scientific substantiation and development of a simulation-mathematical method for calculating the geometric parameters of the flow part in dredge pumps for viscous fluids at the design stage. Practical implications. The developed method for determining the rational blade-outlet inclination angles of the impellers in the dredge pumps for viscous fluids can be recommended to scientific-research and industrial organizations for use in the improvement, design and operation of the dredge pumps.