Rathborey Chan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Rathborey Chan has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Chart Chiemchaisri
Department of Environmental Engineering, Faculty of Engineering, Kasetsart University, Bangkok, Thailand
1 shared publication Khun Eng
Water and Environmental Engineering, Graduate School, Institute of Technology of Cambodia, Phnom Penh 12156, Cambodia
1 shared publication- Nattawin Chawaloesphonsiya
Research Unit on Technology for Oil Spill and Contamination Management, Chulalongkorn University, Bangkok 10330, Thailand
1 shared publication - Penghour Hong
Faculty of Hydrology and Water Resources Engineering, Institute of Technology of Cambodia, Phnom Penh 12156, Cambodia
1 shared publication Phaly Ham
Faculty of Hydrology and Water Resource Engineering, Institute of Technology of Cambodia, Phnom Penh 12156, Cambodia
1 shared publication- Phaly Ham
Faculty of Hydrology and Water Resources Engineering, Institute of Technology of Cambodia, Phnom Penh 12156, Cambodia
1 shared publication
Latest Publications
- Open Access
- 3 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (3) , 1990
Exploring Effective Bio-Cover Materials for Mitigating Methane Emission at a Tropical Landfill
Methane emission and oxidation in different bio-cover materials, i.e., sandy loam, compost, and stabilized wastes, were investigated at a municipal solid waste landfill in Thailand. The bio-cover was purged with extracted landfill gas while methane reduction through biological oxidation was studied. The moisture content in bio-cover materials was maintained with natural rainwater during the wet period and leachate irrigation during the dry period. Methane emissions were found to vary between media and were influenced by rainfall. The methane loading rates of the bio-cover varied from 8.2–20.3 mol/m3/d, being higher during the dry period. Methane removal rates at the bottom part of the biofilter (0.4–0.6 m depth), the most active zone, were found to be from 6.4–10.9 and 7.8–11.4 mol/m3/d during wet and dry periods. The highest methane removals were found in the lower part of sandy loam, followed sequentially by compost and stabilized wastes. Nevertheless, compost had the highest methane oxidation capacities and greater methanotroph population compared to sandy loam and stabilized wastes. Methanotroph type I was found to predominate during the dry period, whereas methanotroph type II was predominant during the wet period.
- 3 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (3) , 1990
Open AccessExploring Effective Bio-Cover Materials for Mitigating Methane Emission at a Tropical Landfill
Methane emission and oxidation in different bio-cover materials, i.e., sandy loam, compost, and stabilized wastes, were investigated at a municipal solid waste landfill in Thailand. The bio-cover was purged with extracted landfill gas while methane reduction through biological oxidation was studied. The moisture content in bio-cover materials was maintained with natural rainwater during the wet period and leachate irrigation during the dry period. Methane emissions were found to vary between media and were influenced by rainfall. The methane loading rates of the bio-cover varied from 8.2–20.3 mol/m3/d, being higher during the dry period. Methane removal rates at the bottom part of the biofilter (0.4–0.6 m depth), the most active zone, were found to be from 6.4–10.9 and 7.8–11.4 mol/m3/d during wet and dry periods. The highest methane removals were found in the lower part of sandy loam, followed sequentially by compost and stabilized wastes. Nevertheless, compost had the highest methane oxidation capacities and greater methanotroph population compared to sandy loam and stabilized wastes. Methanotroph type I was found to predominate during the dry period, whereas methanotroph type II was predominant during the wet period.
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2785 (1)
Optimization of nitrate production from aquaculture wastewater in a high-rate aerobic reactor for a hydroponic spinach growth
This study aims to optimize nitrate (NO3-) production from synthetic aquaculture wastewater in the high-rate aerobic reactor (HRAR) for hydroponic spinach growth. The high-rate aerobic condition (Dissolve Oxygen: 5-6 mg/L) was tested in a batch diffused aerator with a pH of 5-8 while the biomass concentration and hydraulic retention time (HRT) varied 2-8 g/L and 1-5 hr. As a consequence of the batch tests, an optimum operating condition for the HRAR was determined, and the effluent containing NO3 was subsequently utilized to grow spinach in a hydroponic system. After a longer operation, an optimal condition was defined as a biomass concentration of 4 g/L and HRT of 4 hr, with a pH value ranging from 7 to 8. At this condition, NO3- production could reach up to 10 mg/L within this condition with a nitrification rate of around 0.68 mg/g Biomass.hr, whereas chemical oxygen demand (COD) and ammonia (NH3+) removal in the HRAR system was 78.8% and 88.4%, respectively. The effluent containing NO3- could grow the spinach in a hydroponic system with the mean weight and length increasing rate of 0.75 g/spinach.d and 0.47 cm/spinach.d. In this case, the mean NO3- consumption rate was estimated at 0.41 mg/spinach.hr. Besides that, the COD and NH3 removal could increase by 6.2% and 4.9% due to the activity of microbes, which were attached to the sponge culture. To sum up, the HRAR operating under neutral to alkaline conditions, HRT of 4 hr, and biomass concentration of 4 g/L could simultaneously optimize NO3 production and remove organic and nitrogen with high removal efficiency. Within the amount of the NO3 production, the spinach produced in the soilless growth method could be harvested within 4 weeks of cultivation.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2785 (1)
Open AccessOptimization of nitrate production from aquaculture wastewater in a high-rate aerobic reactor for a hydroponic spinach growth
This study aims to optimize nitrate (NO3-) production from synthetic aquaculture wastewater in the high-rate aerobic reactor (HRAR) for hydroponic spinach growth. The high-rate aerobic condition (Dissolve Oxygen: 5-6 mg/L) was tested in a batch diffused aerator with a pH of 5-8 while the biomass concentration and hydraulic retention time (HRT) varied 2-8 g/L and 1-5 hr. As a consequence of the batch tests, an optimum operating condition for the HRAR was determined, and the effluent containing NO3 was subsequently utilized to grow spinach in a hydroponic system. After a longer operation, an optimal condition was defined as a biomass concentration of 4 g/L and HRT of 4 hr, with a pH value ranging from 7 to 8. At this condition, NO3- production could reach up to 10 mg/L within this condition with a nitrification rate of around 0.68 mg/g Biomass.hr, whereas chemical oxygen demand (COD) and ammonia (NH3+) removal in the HRAR system was 78.8% and 88.4%, respectively. The effluent containing NO3- could grow the spinach in a hydroponic system with the mean weight and length increasing rate of 0.75 g/spinach.d and 0.47 cm/spinach.d. In this case, the mean NO3- consumption rate was estimated at 0.41 mg/spinach.hr. Besides that, the COD and NH3 removal could increase by 6.2% and 4.9% due to the activity of microbes, which were attached to the sponge culture. To sum up, the HRAR operating under neutral to alkaline conditions, HRT of 4 hr, and biomass concentration of 4 g/L could simultaneously optimize NO3 production and remove organic and nitrogen with high removal efficiency. Within the amount of the NO3 production, the spinach produced in the soilless growth method could be harvested within 4 weeks of cultivation.
- Open Access
- 4 January 2022
- Published by MDPI AG in Chemengineering
- Vol. 6 (1) , 3
Development of Integrated Electrocoagulation-Sedimentation (IECS) in Continuous Mode for Turbidity and Color Removal
The present work focused on the development and evaluation of a compact electrocoagulation (EC) reactor, combined between EC and clarifier processes in continuous modes for decolorization and turbidity removal, named the integrated electrocoagulation-sedimentation reactor (IECS). The experiments were firstly conducted in the four-liter batch column in order to optimize the EC configuration and operation condition. The removal kinetics were also investigated and predicted for kinetic correlations. After various optimization steps, the IECS reactor was conducted, consisting of EC and clarifier compartments. Liquid flow pattern in EC compartment was examined through resident time distribution technique for defining the number of EC units and divided baffles. In summary, four units of EC were placed in the EC compartment of the IECS reactor with 90% in the width of three baffles. Each EC unit had two pairs of aluminum electrode plats in monopolar arrangement with a 1.5 cm gap and required a current density of 13.5 mA/cm2. For the clarifier compartment, it was mainly designed based on the batch settling test for separating the precipitated particles. The treatment performance of the IECS reactor was tested at different liquid flows in order to reduce the pollutant to a certain level. For the individual condition, liquid flow rates of 3 and 1 L/min were defined for turbidity and color, respectively. If both pollutants are presented simultaneously, a liquid flow rate of 1–2 L/min can be used for decreasing turbidity from 250 to <20 NTU and color from 6000 to <300 ADMI.
- 4 January 2022
- Published by MDPI AG in Chemengineering
- Vol. 6 (1) , 3
Open AccessDevelopment of Integrated Electrocoagulation-Sedimentation (IECS) in Continuous Mode for Turbidity and Color Removal
The present work focused on the development and evaluation of a compact electrocoagulation (EC) reactor, combined between EC and clarifier processes in continuous modes for decolorization and turbidity removal, named the integrated electrocoagulation-sedimentation reactor (IECS). The experiments were firstly conducted in the four-liter batch column in order to optimize the EC configuration and operation condition. The removal kinetics were also investigated and predicted for kinetic correlations. After various optimization steps, the IECS reactor was conducted, consisting of EC and clarifier compartments. Liquid flow pattern in EC compartment was examined through resident time distribution technique for defining the number of EC units and divided baffles. In summary, four units of EC were placed in the EC compartment of the IECS reactor with 90% in the width of three baffles. Each EC unit had two pairs of aluminum electrode plats in monopolar arrangement with a 1.5 cm gap and required a current density of 13.5 mA/cm2. For the clarifier compartment, it was mainly designed based on the batch settling test for separating the precipitated particles. The treatment performance of the IECS reactor was tested at different liquid flows in order to reduce the pollutant to a certain level. For the individual condition, liquid flow rates of 3 and 1 L/min were defined for turbidity and color, respectively. If both pollutants are presented simultaneously, a liquid flow rate of 1–2 L/min can be used for decreasing turbidity from 250 to <20 NTU and color from 6000 to <300 ADMI.