Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hadi Gholamiyan has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Surface properties of oak wood (Quercus castaneifolia) coated with polyester reinforced with ceramic nanoparticles using a plasma deposition technique

    by Hadi Gholamiyan, Behnam Gholampoor, Akbar Mastouri, Reza Hosseinpourpia

    The surface performance and weathering resistance of wood products often depend on the applied coating and reinforcing additives. In this paper, polyester film with the contribution of ceramic nanoparticles (contains zinc oxide, ZnO) was deposited on the oak wood ( Quercus castaneifolia ) surfaces via atmospheric pressure plasma jet (APPJ) technology. The polyester coating applied with an applicator and uncoated wood samples served as controls. The surface properties such as surface roughness, contact angle, wear index, wear depth and hardness values of the samples were analyzed before and after 720-h exposure to the artificial accelerated weathering test. The results demonstrated that the surface properties of oak samples were considerably improved after coating, and superior performances were observed in the plasma-deposited coating layer, particularly the ones reinforced with ceramic nanoparticles. This indicates a potential for using the plasma deposition method for coating and enhancing the surface properties of wood.


  • Open Access

    Surface Wettability and Coating Performance of Plasma-Treated Wood-Based Composite Panels

    by Hadi Gholamiyan, Javad Ashouri, Peyman Ahmadi, Reza Hosseinpourpia

    The effect of dielectric barrier discharge (DBD) plasma treatment was studied on the surface characteristics and coating performance of transparent epoxy resin on the surface of particleboard (PB) and medium-density fiberboard (MDF). The plasma treatment was performed at three plasma energies (10, 15, and 20 kW) and three distances from the nozzle (10, 20, and 30 mm). Analyzing the samples by Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS) indicated the changes of their chemical structure by means of the plasma treatment. The contact angle study showed a significant increase in surface wettability after plasma treatment with a pronounced effect observed by treatment parameters. The surface roughness was also significantly increased by the plasma treatment. The strength of the coating adhesion to the surface of the PB and MDF composite panels was also significantly improved by the plasma treatment, while no obvious trend was observed by treatment parameters. The highest adhesion strength of 2.03 MPa and 3.63 MPa were obtained by the PB and MDF samples, respectively, treated at a 10 mm nozzle distance and 15 kW plasma energy. The scratch resistance of the epoxy coatings showed a similar trend as the adhesion strength illustrating an inferior isolated surface of the coating after the plasma treatment.


  • Effects of cutting parameters on the sound level and surface quality of sawn wood

    by Hadi Gholamiyan, Behnam Gholampoor, Ali Hassanpoor Tichi

    This study investigated the effect of cutting conditions effects on sound level and surface quality in softwood and hardwood. The sound emission level caused by cutting process (band saw) as well as the surface roughness and topography of the wood samples were evaluated. A direct relationship was found between sound emission level and density, moisture content, feeding rate, and dimensions of the samples. Straight cutting of the samples caused less sound emission than cutting in a curved direction. The protective effect of the earmuffs was very significant, reducing the sound emission level from 88 dB to 38 dB. The results showed that with increasing the density and dimensions of the samples, the surface roughness decreased, while with increasing the moisture content and feeding rate, changing the cutting direction from straight to curved, the surface roughness of the samples increased.


  • Open Access

    Application of Waterborne Acrylic and Solvent-Borne Polyester Coatings on Plasma-Treated Fir (Abies alba M.) Wood

    by Hadi Gholamiyan, Behnam Gholampoor, Reza Hosseinpourpia

    This research investigates the effect of plasma treatment with air, nitrogen (N2), and carbon dioxide (CO2) gases on the performance of waterborne (acrylic) and solvent-borne (polyester) coated fir (Abies alba M.) wood samples. The properties of the plasma-coated samples were analyzed before and after exposure to accelerated weathering and compared with those of untreated and solely treated ones. According to pull-off testing, the coating adhesion of the wood samples was considerably improved by plasma treatment, and obvious differences were observed between different plasma gases. The effect was more pronounced after the weathering test. Similar results were obtained for the abrasion resistance of the samples. The water contact angle measurement illustrated more hydrophilic character in the solely plasma-treated wood in comparison with the untreated wood. The application of coatings, however, strongly improved its hydrophobic character. The performances of waterborne and solvent-borne coatings on plasma-treated wood were comparable, although slightly better values were obtained by the waterborne system. Our results exhibit the positive effect of plasma treatment on coating performances and the increased weather resistance of the waterborne and solvent-borne coating systems on plasma-treated wood.


  • Silane nanofilm formation by sol-gel processes for promoting adhesion of waterborne and solvent-borne coatings to wood surface

    by Hadi Gholamiyan, Asghar Tarmian, Zahra Ranjbar, Ali Abdulkhani, Mohammad Azadfallah, Carsten Mai

    The objective of this study was to promote the adhesion of waterborne and solvent-borne coatings [polyurethane (PU) and alkyd] on wood surfaces by silane nanofilm formation by means of sol-gel processes. Tetraethoxysilane and glycidoxypropyltrimethoxysilane served as sol-gel materials. The silane-based materials improved the adhesion strength. The positive effects can be explained by the changes in the wood surface chemistry induced by the sol-gel process. High-resolution X-ray photoelectron spectroscopy (XPS) showed an increase in -C-H and -C-C bonds and a decrease in -C-O bond. Microscopic observation by fluorescence and confocal laser scanning microscopy together with NIS-Elements analysis software showed that the silica component of nanosol covered the whole wood surface homogeneously, whereas alkyd and PU coatings were deposited preferentially in the surface depressions. The combined analysis of energy-dispersive X-ray analysis and XPS demonstrated that the surface was covered with silicon oxides (SiO2) attached to hydrocarbon chains.