Didem Tekgun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Didem Tekgun has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Burak Tekgun
Department of Electrical and Electronics Engineering, Abdullah Gul University, Kayseri 38100, Turkey
4 shared publications - Irfan Alan
Department of Electrical and Electronics Engineering, Abdullah Gul University, Kayseri, Turkey
2 shared publications Irfan Alan
Department of Electrical and Electronics Engineering, Abdullah Gul University, Kayseri, Turkey
1 shared publication
Latest Publications
- Open Access
Open-End Winding Induction Machine Drives Under Unbalanced Phase Impedances
Manufacturing tolerances and winding-layout variations can introduce phase-to-phase mismatches in stator resistance and leakage inductance. Under such unbalanced phase impedances, conventional field-oriented control (FOC), typically designed under balanced-parameter assumptions, may produce unequal phase currents, distorted airgap MMF, reduced efficiency, increased torque ripple, and undesired vibro-acoustic behavior. This paper investigates an open-end winding (OEW) induction machine (IM) drive, in which each phase is independently driven by an H-bridge inverter fed by the same DC source. To mitigate phase–current imbalance without parameter estimation, an RMS-based phase–current-balancing controller is proposed. The controller continuously calculates the RMS value of each phase current and adaptively scales the corresponding reference-phase voltage in a low-bandwidth outer loop, while preserving the classical FOC structure. The balancing law is derived directly from the phase-impedance imbalance model; convergence of the three coupled per-phase loops is proven via a Lyapunov argument, and stability of the cascaded structure is established through an analytical bandwidth-separation analysis shown to be robust to ±30% machine-parameter variation and across the 500–1500 rev/min speed range. Simulation and experimental results across multiple operating points demonstrate effective phase–current equalization.
Open AccessOpen-End Winding Induction Machine Drives Under Unbalanced Phase Impedances
Manufacturing tolerances and winding-layout variations can introduce phase-to-phase mismatches in stator resistance and leakage inductance. Under such unbalanced phase impedances, conventional field-oriented control (FOC), typically designed under balanced-parameter assumptions, may produce unequal phase currents, distorted airgap MMF, reduced efficiency, increased torque ripple, and undesired vibro-acoustic behavior. This paper investigates an open-end winding (OEW) induction machine (IM) drive, in which each phase is independently driven by an H-bridge inverter fed by the same DC source. To mitigate phase–current imbalance without parameter estimation, an RMS-based phase–current-balancing controller is proposed. The controller continuously calculates the RMS value of each phase current and adaptively scales the corresponding reference-phase voltage in a low-bandwidth outer loop, while preserving the classical FOC structure. The balancing law is derived directly from the phase-impedance imbalance model; convergence of the three coupled per-phase loops is proven via a Lyapunov argument, and stability of the cascaded structure is established through an analytical bandwidth-separation analysis shown to be robust to ±30% machine-parameter variation and across the 500–1500 rev/min speed range. Simulation and experimental results across multiple operating points demonstrate effective phase–current equalization.
- Open Access
- 14 January 2026
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- No. 15,p. 1-8
Eccentricity fault indices in synchronous reluctance machines with different rotor geometries
Synchronous reluctance motors (SynRMs) have gained significant attention in modern drive applications owing to their magnet-free rotor structure, high efficiency, and robust performance under various operating conditions. Nevertheless, SynRMs remain prone to electrical and mechanical faults that can deteriorate their reliability. Among these, eccentricity faults are critical, as even minor misalignments between the rotor and stator can lead to unbalanced magnetic forces, increased vibration, and electromagnetic stress. This study investigates static (SE), dynamic (DE), and mixed (ME) eccentricity faults in SynRMs featuring three and four-flux barrier rotor geometries through 2D transient finite element analysis. The results reveal that ME causes the most severe electromagnetic distortion, while the three-flux barrier rotor exhibits higher torque ripple and reduced torque capability due to diminished saliency. Torque ripple is identified as the most sensitive fault indicator, increasing by up to 33% under ME. These findings provide valuable insights into the relationship between rotor geometry, fault severity, and machine performance, guiding future SynRM design and monitoring strategies.
- 14 January 2026
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- No. 15,p. 1-8
Open AccessEccentricity fault indices in synchronous reluctance machines with different rotor geometries
Synchronous reluctance motors (SynRMs) have gained significant attention in modern drive applications owing to their magnet-free rotor structure, high efficiency, and robust performance under various operating conditions. Nevertheless, SynRMs remain prone to electrical and mechanical faults that can deteriorate their reliability. Among these, eccentricity faults are critical, as even minor misalignments between the rotor and stator can lead to unbalanced magnetic forces, increased vibration, and electromagnetic stress. This study investigates static (SE), dynamic (DE), and mixed (ME) eccentricity faults in SynRMs featuring three and four-flux barrier rotor geometries through 2D transient finite element analysis. The results reveal that ME causes the most severe electromagnetic distortion, while the three-flux barrier rotor exhibits higher torque ripple and reduced torque capability due to diminished saliency. Torque ripple is identified as the most sensitive fault indicator, increasing by up to 33% under ME. These findings provide valuable insights into the relationship between rotor geometry, fault severity, and machine performance, guiding future SynRM design and monitoring strategies.
- Open Access
Modified Induction Machine Equivalent Circuit Including Solid Shaft Eddy Currents
The shaft eddy currents cause a significant saturation in two-pole induction machines (IMs) as they generate an opposing field and repulse the main flux, thus tightening the flux path. This results in inaccurate performance estimations with the magnetizing inductance measured in no-load conditions when the machine is loaded. This article presents a modified IM equivalent circuit considering the rotor back iron saturation effects caused by the solid shaft eddy currents using experimental measurements and recursive parameter estimation techniques. The classical equivalent circuit (CEC) parameters are determined with the standard test techniques followed by the parameter estimation of the newly introduced modified equivalent circuit (MEC) parameters. The proposed modified equivalent circuit is benchmarked with CEC and finite element analysis (FEA) simulations with and without considering eddy effects. The proposed MEC model and the FEA that consider eddy effects performed better than the other models and yielded a negligibly small error over a wide range of loading conditions. Compared to the FEA, the proposed MEC estimates the IM performance much faster, which makes it more appealing for IM performance estimations.
Open AccessModified Induction Machine Equivalent Circuit Including Solid Shaft Eddy Currents
The shaft eddy currents cause a significant saturation in two-pole induction machines (IMs) as they generate an opposing field and repulse the main flux, thus tightening the flux path. This results in inaccurate performance estimations with the magnetizing inductance measured in no-load conditions when the machine is loaded. This article presents a modified IM equivalent circuit considering the rotor back iron saturation effects caused by the solid shaft eddy currents using experimental measurements and recursive parameter estimation techniques. The classical equivalent circuit (CEC) parameters are determined with the standard test techniques followed by the parameter estimation of the newly introduced modified equivalent circuit (MEC) parameters. The proposed modified equivalent circuit is benchmarked with CEC and finite element analysis (FEA) simulations with and without considering eddy effects. The proposed MEC model and the FEA that consider eddy effects performed better than the other models and yielded a negligibly small error over a wide range of loading conditions. Compared to the FEA, the proposed MEC estimates the IM performance much faster, which makes it more appealing for IM performance estimations.
- Open Access
Investigating the Role of Stator Slot Indents in Minimizing Flooded Motor Fluid Damping Loss
This research examines how fluid damping loss affects the operation of a two-pole, 5.5 HP (4 kW) induction machine (IM) within the context of different slot opening configurations developed for downhole water pump applications. Since these motors operate with their cavities filled with fluid, the variations in fluid viscosity and density, compared to air, result in the occurrence of damping losses. Furthermore, this loss can be attributed to the motor’s stator and rotor surface geometry, as the liquid within the motor cavity moves unrestrictedly within the motor housing. This study involves the examination of the damping loss in a 24-slot IM under different stator slot indentations. The investigation utilizes computational fluid dynamics (CFD) finite element analysis (FEA) and is subsequently validated through experiments. The aim of this work is to emphasize the significance of fluid damping loss in submerged machines. Results reveal that the damping loss exceeds 8% of the motor output power when the stator surface has indentations, and it diminishes to 3.2% of the output power when a custom wedge structure is employed to eliminate these surface indentations.
Open AccessInvestigating the Role of Stator Slot Indents in Minimizing Flooded Motor Fluid Damping Loss
This research examines how fluid damping loss affects the operation of a two-pole, 5.5 HP (4 kW) induction machine (IM) within the context of different slot opening configurations developed for downhole water pump applications. Since these motors operate with their cavities filled with fluid, the variations in fluid viscosity and density, compared to air, result in the occurrence of damping losses. Furthermore, this loss can be attributed to the motor’s stator and rotor surface geometry, as the liquid within the motor cavity moves unrestrictedly within the motor housing. This study involves the examination of the damping loss in a 24-slot IM under different stator slot indentations. The investigation utilizes computational fluid dynamics (CFD) finite element analysis (FEA) and is subsequently validated through experiments. The aim of this work is to emphasize the significance of fluid damping loss in submerged machines. Results reveal that the damping loss exceeds 8% of the motor output power when the stator surface has indentations, and it diminishes to 3.2% of the output power when a custom wedge structure is employed to eliminate these surface indentations.
- Open Access
- 11 September 2023
- Published by Elsevier in Ain Shams Engineering Journal
- Vol. 15 (3)
A multi-functional quasi-single stage bi-directional charger topology for electric vehicles
- 11 September 2023
- Published by Elsevier in Ain Shams Engineering Journal
- Vol. 15 (3)
Open AccessA multi-functional quasi-single stage bi-directional charger topology for electric vehicles
- 1 February 2022
- Published by SAGE Publications in International Journal of Applied Electromagnetics and Mechanics
- Vol. 70 (1) , 73-93
A new oval shaft, high performance, 2 pole line start synchronous reluctance machine for submersible pump applications
In this paper, a 2 pole, 4 kW, 6 inches diameter line start synchronous reluctance machine (LS-SynRM) as a submersible water pump motor is designed and optimized with a new oval shaft structure. The aim is to improve the machine performance by widening the flux path on the rotor via narrowing down the shaft on the q-axis. This way a wider d-axis flux path is obtained, and accordingly, the d-axis inductance, the saliency ratio L d∕ L q, and the inductance difference L d– L q are increased. First, a set of structural analyses is carried out on a 7-flux barrier rotor in 3 stages: modal, harmonic, and static structural analyses. According to analysis results, the safe limit for the shaft size reduction is determined as 8 mm to avoid excessive deformations and undesired vibrations due to resonance. Later, the machine is optimized using Multi-Objective Differential Evolution (MODE) algorithm with a narrower shaft. The quality of the Pareto front solutions shows that the oval shaft machine is superior to the circular shaft machine in terms of efficiency, motor mass, and torque ripple. The maximum recorded efficiency improvement for the same size LS-SynRM is 4 points and the same size commercial induction machine is around 20 points.
- 1 February 2022
- Published by SAGE Publications in International Journal of Applied Electromagnetics and Mechanics
- Vol. 70 (1) , 73-93
A new oval shaft, high performance, 2 pole line start synchronous reluctance machine for submersible pump applications
In this paper, a 2 pole, 4 kW, 6 inches diameter line start synchronous reluctance machine (LS-SynRM) as a submersible water pump motor is designed and optimized with a new oval shaft structure. The aim is to improve the machine performance by widening the flux path on the rotor via narrowing down the shaft on the q-axis. This way a wider d-axis flux path is obtained, and accordingly, the d-axis inductance, the saliency ratio L d∕ L q, and the inductance difference L d– L q are increased. First, a set of structural analyses is carried out on a 7-flux barrier rotor in 3 stages: modal, harmonic, and static structural analyses. According to analysis results, the safe limit for the shaft size reduction is determined as 8 mm to avoid excessive deformations and undesired vibrations due to resonance. Later, the machine is optimized using Multi-Objective Differential Evolution (MODE) algorithm with a narrower shaft. The quality of the Pareto front solutions shows that the oval shaft machine is superior to the circular shaft machine in terms of efficiency, motor mass, and torque ripple. The maximum recorded efficiency improvement for the same size LS-SynRM is 4 points and the same size commercial induction machine is around 20 points.
- 4 January 2022
- Published by Springer Nature in Electrical Engineering
- Vol. 104 (4) , 1985-1995
FEA based fast topology optimization method for switched reluctance machines
- 4 January 2022
- Published by Springer Nature in Electrical Engineering
- Vol. 104 (4) , 1985-1995
FEA based fast topology optimization method for switched reluctance machines