Paulo Augusto Tonini Arpini
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Paulo Augusto Tonini Arpini has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Élcio Cassimiro Alves
Department of Civil Engineering, Federal University of Espírito Santo, Vitória 29075-910, ES, Brazil
2 shared publications - Adenilcia Fernanda Grobério Calenzani
Universidade Federal do Espírito Santo, Brasil
1 shared publication - Breno Dias Breda
Universidade Federal do Espírito Santo, Brasil
1 shared publication - Gabriel Erlacher
Universidade Federal do Espírito Santo, Brasil
1 shared publication - Jéssica Salomão Lourenção
Universidade Federal do Espírito Santo, Brasil
1 shared publication - Mayane C. Loureiro
Universidade Federal do Espírito Santo, Brasil
1 shared publication
Latest Publications
- Open Access
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 15 (1)
Optimized design of concrete-filled steel columns
The objective of this paper is to present the formulation of the optimization problem and its application to the design of concrete-filled composite columns with and without reinforcement steel bars, according to recommendations from NBR 8800:2008, NBR 16239:2013 and EN 1994-1-1:2004. A comparative analysis between the aforementioned standards is performed for various geometries considering cost, efficiency and materials in order to verify which parameters influence the solution of the composite column that satisfies the proposed problems. The solution of the optimization problem is obtained by using the genetic algorithm method featured in MATLAB’s guide toolbox. For the examples analyzed, results show that concretes with compressive strength greater than 50MPa directly influence the solution of the problem regarding cost and resistance to normal forces.
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 15 (1)
Open AccessOptimized design of concrete-filled steel columns
The objective of this paper is to present the formulation of the optimization problem and its application to the design of concrete-filled composite columns with and without reinforcement steel bars, according to recommendations from NBR 8800:2008, NBR 16239:2013 and EN 1994-1-1:2004. A comparative analysis between the aforementioned standards is performed for various geometries considering cost, efficiency and materials in order to verify which parameters influence the solution of the composite column that satisfies the proposed problems. The solution of the optimization problem is obtained by using the genetic algorithm method featured in MATLAB’s guide toolbox. For the examples analyzed, results show that concretes with compressive strength greater than 50MPa directly influence the solution of the problem regarding cost and resistance to normal forces.
- Open Access
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 15 (3)
Optimum design of a composite floor system considering environmental and economic impacts
The composite floor system, composed of steel deck and concrete slab, generates more efficient and economical structures. On the other hand, the design of this type of structure has a high complexity level due to the consideration of several variables. In this respect, the objective of this paper is to present the formulation of the optimization problem for a composite floor system (steel and concrete) considering such environmental as economic impacts. To formulate the optimization problem, the reduction of environmental impact was adopted as an objective function - assuming the CO2 emission and the finance cost as parameters. The restrictions were taken by the limiting states imposed in standard NBR 8800:2008. The computer program was developed via Matlab R2016a and the optimization process was carried out using the Genetic Algorithm toolbox existing in this platform. Two application examples of the formulation at hand are presented: the first from the literature and the second from an existing building - in both situations the influences of different concrete compressive characteristic strengths were analyzed. The results of the optimization problem show a reduction in geometry and, consequently, in its weight. The solution found by the program reduces by up to 17.70% of CO2 emissions and 17.47% of the finance cost. When was applying different concrete compressive strengths, the optimal solution for environmental impact did not get the lowest cost. In general, the steel deck formwork obtained the highest percentage of environmental impact, while the beams and girders, with the same shape configuration, had the highest finance cost. Therefore, it is shown that the optimal design solution to CO2 emissions is not always the better solution for the finance cost.
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 15 (3)
Open AccessOptimum design of a composite floor system considering environmental and economic impacts
The composite floor system, composed of steel deck and concrete slab, generates more efficient and economical structures. On the other hand, the design of this type of structure has a high complexity level due to the consideration of several variables. In this respect, the objective of this paper is to present the formulation of the optimization problem for a composite floor system (steel and concrete) considering such environmental as economic impacts. To formulate the optimization problem, the reduction of environmental impact was adopted as an objective function - assuming the CO2 emission and the finance cost as parameters. The restrictions were taken by the limiting states imposed in standard NBR 8800:2008. The computer program was developed via Matlab R2016a and the optimization process was carried out using the Genetic Algorithm toolbox existing in this platform. Two application examples of the formulation at hand are presented: the first from the literature and the second from an existing building - in both situations the influences of different concrete compressive characteristic strengths were analyzed. The results of the optimization problem show a reduction in geometry and, consequently, in its weight. The solution found by the program reduces by up to 17.70% of CO2 emissions and 17.47% of the finance cost. When was applying different concrete compressive strengths, the optimal solution for environmental impact did not get the lowest cost. In general, the steel deck formwork obtained the highest percentage of environmental impact, while the beams and girders, with the same shape configuration, had the highest finance cost. Therefore, it is shown that the optimal design solution to CO2 emissions is not always the better solution for the finance cost.