Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Shafahat Ali has a total of 39 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Optimizing Charpy Impact Strength of Material‐Extruded PLA Through Layer Height, Raster Angle, and Infill Geometry

    by Yazan Mashaki, Luis Hoi Fan, Shafahat Ali, Salman Pervaiz, Ibrahim Deiab

    The impact performance of material‐extruded polymer components is strongly influenced by process‐dependent internal structure, making parameter selection critical for applications requiring improved damage tolerance. In this study, the Charpy impact strength of polylactic acid (PLA) parts fabricated by material extrusion was investigated using a three‐factor, three‐level full factorial design. The effects of layer height (0.1, 0.2, and 0.3 mm), raster angle (0°, 45°, and 90°), and infill geometry (triangle, octet, and gyroid) were evaluated across 27 unique processing conditions. By evaluating all parameter combinations using PLA at a fixed infill density of 20%, the full factorial design enabled determination of both the individual and interaction effects of the three parameters, rather than considering only isolated parameter trends. ISO 179‐compliant specimens were manufactured and tested under Charpy impact loading. Analysis of variance revealed that layer height was the primary factor influencing impact strength, followed by raster angle and its interaction with layer height, while infill geometry also made a significant contribution to the response. The highest impact strength of 10.59 ± 0.02 kJ/m 2 was obtained at a layer height of 0.3 mm, a raster angle of 0°, and an octet infill geometry. In addition to inferential statistical analysis, an ordinary least squares quadratic response model was used to characterize the effect of layer height, indicating diminishing gains near the upper end of the investigated range. The results show that the impact resistance of material‐extruded PLA is governed by a coupled process–structure relationship and provide practical guidance for selecting printing conditions in applications requiring improved toughness and structural reliability.

  • A auxetic metamaterial structure: analysis of shear and bending, mechanical characterization

    by Mohammad Anas Khan, Shafahat Ali, Mamoun Alshihabi, Ibrahim Deiab

    Purpose: The purpose of this study is to investigate the potential of auxetic metamaterials, specifically Re-entrant and Re-entrant Triangular unit cell designs, in enhancing the performance of bone screws used in orthopedic surgeries. By leveraging their negative Poisson's ratio properties, these auxetic designs aim to improve screw-bone interfacial stability, reduce loosening and increase load-bearing capacity under shear and bending stresses. Through high-resolution 3D printing and mechanical testing, the study evaluates the effectiveness of auxetic bone screws compared to conventional designs, with the goal of advancing patient-specific, reliable orthopedic implants that enhance clinical outcomes and reduce long-term healthcare costs. Design/methodology/approach: Auxetic bone screws were designed by integrating Re-entrant and Re-entrant Triangular unit cell geometries into the screw body to exploit negative Poisson's ratio behavior. High-resolution 3D printing was employed to fabricate the screws with precise geometrical accuracy, enabling reliable replication of complex auxetic structures. Mechanical performance was evaluated through shear and three-point bending tests, with conventional bone screws serving as controls. Comparative analysis focused on load-bearing capacity, deformation resistance and the influence of auxetic unit cell arrangement. This approach enabled systematic evaluation of auxetic design advantages for improving screw-bone fixation and orthopedic implant reliability. Findings: The results demonstrated that auxetic bone screws, particularly those with Re-entrant Triangular unit cells, exhibited superior mechanical performance compared to conventional screws. They showed higher load-bearing capacity, enhanced deformation resistance and improved screw-bone interfacial stability under shear and bending loads. The auxetic structures' lateral expansion during loading increased contact with the surrounding bone, effectively reducing the likelihood of screw loosening. Additionally, the arrangement and geometry of unit cells significantly influenced performance, with optimized designs achieving the best outcomes. Originality/value: This study is among the first to apply auxetic metamaterial concepts to bone screw design, offering a novel strategy to overcome the persistent problem of screw loosening in orthopedic implants. By integrating Re-entrant and Re-entrant Triangular auxetic unit cells, the research introduces designs that leverage negative Poisson's ratio behavior to actively improve screw-bone fixation under mechanical loading. The combination of high-resolution 3D printing with experimental mechanical testing provides new insights into how auxetic geometries influence implant stability. This original approach highlights the potential for patient-specific, mechanically superior and sustainable orthopedic implants beyond traditional screw designs.

  • Open Access

    4D-printed auxetic biomaterials for adaptive and functional bone implants

    by Shafahat Ali, Mamoun Alshihabi, Said Abdallah, Ali Zolfagharian, Ibrahim Deiab


  • Open Access

    Development of PBAT-Modified Photopolymer Resin Micro-Composites for More Sustainable SLA Additive Manufacturing

    by Mamoun Alshihabi, Shafahat Ali, Ibrahim Deiab

    The photopolymer resins commonly utilized in stereolithography (SLA) additive manufacturing are non-renewable, brittle in nature and have low impact and thermal insulation properties, limiting their applications in sustainable and functional applications. To overcome these shortcomings, this paper introduces the initial research on the use of Polybutylene Adipate Terephthalate (PBAT), a biodegradable polymer, into SLA resins to create partially sustainable micro-composites with enhanced mechanical and thermal capabilities. PBAT micropowder was mixed with standard resin at 1, 5 and 10 wt% and 3D printed using SLA. To determine performance and interfacial morphology, mechanical testing (tensile and impact), thermal conductivity measurements and SEM fracture surface analysis were carried out. Introduction of PBAT significantly increased toughness, flexibility and the impact strength of the 1% PBAT composite stood at 168.63 J/m2 with 68.69 J/m2 of pure resin whereas the 10% PBAT sample was found to be 16% more efficient in thermal insulation. These findings indicate that partially replacing the photopolymer resin with biodegradable PBAT can enhance impact strength and thermal insulation while reducing the overall amount of petrochemical resin required. The article provides a new avenue of eco-friendly, high-performance photopolymer composites to facilitate sustainable additive manufacturing.


  • Open Access

    Influence of Carbon Fiber Reinforcement on Mechanical and Thermal Behavior of PLA and PAHT in Additive Manufacturing

    by Mamoun Alshihabi, Mahdi El Said, Abdussalam Alshami, Shafahat Ali, Ibrahim Deiab

    This study explores the comparative evaluation of PLA, carbon fiber-reinforced PLA (PLA-CF), and carbon fiber-reinforced high-temperature polyamide (PAHT-CF) for use in Fused Deposition Modeling (FDM) additive manufacturing. These materials were selected to examine how carbon fiber (CF) reinforcement affects PLA and PAHT, using virgin PLA as the baseline. Mechanical and thermal properties were tested to assess the influence of reinforcement on strength, toughness, and heat transfer. Tensile, impact, and thermal conductivity tests were conducted on all three materials. The results showed that PAHT-CF outperformed both PLA and PLA-CF in all categories, achieving an ultimate tensile strength of 57.5 MPa, an impact strength of 14.30 kJ/m2, and thermal conductivity of 0.182 W/m·K. PLA-CF showed moderate improvements in strength over neat PLA but with increased brittleness and slight improvement in thermal conductivity. Notably, this is the first study to investigate the thermal conductivity and resistivity of PAHT-CF in the literature, offering new insights into its heat dissipation capabilities and suitability for high-temperature applications. These findings highlight the critical role of polymer selection and fiber reinforcement in optimizing material performance. The results offer guidance for material selection in additive manufacturing, especially for lightweight, strong, and thermally efficient parts in various industries.


  • Open Access

    Dual‐Stimuli Responsive and Sustainable PLA/APHA/TPU Blend for 4D Printing

    by Shafahat Ali, Mamoun Alshihabi, Logan Beard, Ibrahim Deiab, Salman Pervaiz

    4D printing of shape memory polymers (SMPs) offers transformative potential for patient‐specific medical devices, yet current SMPs often face a trade‐off between mechanical toughness and low‐temperature activation. This study presents a novel PLA/APHA/TPU blend filament for 3D printing that overcomes this limitation by combining high strength and flexibility with low‐temperature shape memory activation—features not previously achieved in PLA‐based SMPs. The uniform dispersion of TPU and APHA in the PLA matrix creates a composite with enhanced tensile strength, modulus, and elongation, addressing the brittleness typical of neat PLA. The optimized 60/20/20 wt.% formulation enables rapid shape recovery at ∼39.5°C, significantly below PLA's glass transition, with near‐complete shape fixity (∼100%) and high recovery ratios (>92%) under both thermal and mechanical stimuli. This dual‐responsive behavior is driven by the synergistic roles of TPU (providing ductility) and APHA (enhancing flexibility and thermal sensitivity). The composite also retains excellent printability and biocompatibility, making it ideal for next‐generation biomedical SMP applications such as 4D‐printed orthopedic braces, soft robotic actuators, and adaptive implants. Using bio‐based, biodegradable polymers, this work advances eco‐friendly, high‐performance SMPs for additive manufacturing, setting a new benchmark for PLA‐based 4D‐printable materials.


  • Open Access

    Progress on Sustainable Cryogenic Machining of Hard-to-Cut Material and Greener Processing Techniques: A Combined Machinability and Sustainability Perspective

    by Shafahat Ali, Said Abdallah, Salman Pervaiz, Ibrahim Deiab

    The current research trends of production engineering are based on optimizing the machining process concerning human and environmental factors. High-performance materials, such as hardened steels, nickel-based alloys, fiber-reinforced polymer (FRP) composites, and titanium alloys, are classified as hard-to-cut due to their ability to maintain strength at high operating temperatures. Due to these characteristics, such materials are employed in applications such as aerospace, marine, energy generation, and structural. The purpose of this article is to investigate the machinability of these alloys under various cutting conditions. The purpose of this article is to compare cryogenic cooling and cryogenic processing from the perspective of machinability and sustainability in the manufacturing process. Compared to conventional machining, hybrid techniques, which mix cryogenic and minimal quantity lubricant, led to significantly reduced cutting forces of 40–50%, cutting temperatures and surface finishes by approximately 20–30% and more than 40%, respectively. A carbon footprint is determined by several factors including power consumption, energy requirements, and carbon dioxide emissions. As a result of the cryogenic technology, the energy consumption, power consumption, and CO2 emissions were reduced by 40%, 28%, and 35%.


  • Open Access

    Optimization Scheme for 3D Printing of PLA–PHBV–PCL Biodegradable Blends for Use in Orthopedic Casting

    by Muhammad Mohid Aziz, Logan Beard, Shafahat Ali, Abdelkrem Eltaggaz, Ibrahim Deiab

    Three-dimensional printing technology offers significant advantages in the production of orthopedic casts, providing a promising alternative to conventional plaster and fiberglass materials. Polylactic acid (PLA) is widely used for this purpose; however, its adoption is limited due to poor mechanical properties, including high brittleness, low thermal stability, and limited elongation. These challenges can be mitigated by blending PLA with other biodegradable polymers. This study investigated a blend of PLA with poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), a type of polyhydroxyalkanoate (PHA), and polycaprolactone (PCL) for the development of 3D printed orthopedic casts. The key mechanical properties—tensile strength, percent elongation at break, Young’s modulus, flexural strength, flexural modulus, and impact strength—were evaluated as a function of the printing parameters, including nozzle temperature, layer height, and raster angle. The grey relational analysis (GRA) approach was applied to optimize these mechanical properties. The optimal printing parameters were found to be a nozzle temperature of 180 °C, a layer height of 0.18 mm, and a raster angle of 0°, resulting in a tensile strength of 44.4 ± 4.4 MPa, an elongation at break of 68.5 ± 11.6%, a Young’s modulus of 948.7 ± 25.1 MPa, a flexural strength of 54.6 ± 8.9 MPa, a flexural modulus of 1549.3 ± 141 MPa, and an impact strength of 80.77 ± 5.6 J/m. Statistical analysis using analysis of variance (ANOVA) revealed that for tensile strength, 50.18% was influenced by the raster angle, 26.38% by the layer height, and 18.92% by the nozzle temperature; for flexural strength, 69.81% was influenced by the raster angle, 20.67% by the layer height, and 3.53% by the nozzle temperature; and for impact strength, 75.11% was influenced by the raster angle, 13.16% by the layer height, and 4.45% by the nozzle temperature.