Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Indira Tashmukhanbetova has a total of 76 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Investigation of the Main Performance Indicators of Thermal-Insulating Dry-Mix Mortars Based on Shell Limestone Filler and Containing Hollow Glass Microspheres

    by Yelzhan S. Orynbekov, Zaure N. Altayeva, Ruslan E. Nurlybayev, Axaya S. Yestemessova, Aktota A. Murzagulova, Alinur A. Iskakov, Gaukhar K. Abisheva, Abzal N. Alikhan, Indira B. Tashmukhanbetova

    This paper presents a study of thermal-insulating dry-mix mortars containing shell limestone, shell limestone extraction waste, and hollow microspheres. The effects of shell limestone and fillers on physical, mechanical, and thermal properties were investigated. The microstructure of shell limestone was examined by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) using a JEOL JSM-7000F scanning electron microscope. The elemental mass fractions confirmed the carbonate nature of the shell limestone raw material (wt.%: O, 50.3–43.7; Ca, 34.1–44.2; C, 15.6–12.1). Finely dispersed fillers, hollow glass microspheres, and amorphous aluminosilicates were found to be suitable for producing a low-density thermal-insulating lime–shell limestone–cement composition. The particle size of the shell limestone powder was 5.67 × 10−6 m, with calcium carbonate (CaCO3) and silica (SiO2) contents of 71.0% and 22.5%, respectively. The shell limestone and microsphere proportions in the binder substantially affected thermal conductivity (0.090–0.113 W/(m·°C)), compressive strength (3.25–4.05 MPa), adhesion strength to the substrate (0.8–1.2 MPa), flexural tensile strength (2.0–2.5 MPa), and water absorption coefficient (0.3–0.5%). The optimum thermal-insulating dry-mix formulation contained, by mass: lime, 25–40%; shell limestone, 15–20%; glass microspheres, 15–20%; amorphous aluminosilicates, 5–10%; diatomite, 2–10%; and cement, 0.5–4.0%.

  • SERVICE PERFORMANCE OF CRACK REPAIR IN CONCRETE TRANSPORTATION AND CIVIL INFRASTRUCTURE UNDER SEVERE CONTINENTAL CLIMATES: A CRITICAL REVIEW

    by I. Tashmukhanbetova

    Concrete crack repair in transport and civil infrastructure is governed by defect cause, moisture, movement, installation conditions and retained interface function, not by product strength alone. Severe continental service adds cold application, saturation, freeze–thaw, deicing salts, thermal movement, abrasion and traffic loading. This targeted critical evidence review considered 60 sources published in 2000-2026: 51 peer-reviewed papers and nine standards, agency reports or official sources. The corpus comprised a 45-source core and 15 DOI-verified records added through a focused regional, coupled-exposure and 2026 update. Evidence was coded by repair function, application variables, outcome, validation scale and direct or supporting role; incompatible tests were not pooled. Stable structural cracks may justify low-viscosity rigid injection, whereas water-bearing or moving cracks require leakage- or movement-oriented systems. Within individual studies, gravity-filled epoxy reduced the compressive-strength deficit to 8.23%; low-viscosity epoxy produced a 25% greater slant-shear response than a high-viscosity comparator; and low-temperature epoxy pre-curing increased wet bond by up to 34.3% while reducing cured-resin shrinkage by 12.0%. Direct coupled abrasion-freeze-thaw and bond-deterioration studies confirm that initial strength cannot represent retained interface performance. A threshold-based selection framework is proposed, but it remains an author-developed framework requiring prospective validation. Regional field comparisons, long-duration conditioned interfaces and monitored pilot repairs remain priority gaps.

  • Open Access

    Mechanochemically Activated Ternary Modifier Based on Technogenic Mineral Waste for High-Performance Concrete

    by Ruslan E. Nurlybayev, Axaya S. Yestemessova, Zaure N. Altayeva, Yelzhan S. Orynbekov, Aktota A. Murzagulova, Maxat Zh. Bulenbayev, Bakytkul U. Yerkebayeva, Indira B. Tashmukhanbetova

    This article presents the results of a research study on the development and evaluation of a mineral modifying additive for concrete produced from mineral processing tailings, shale waste from shungite production, and silica fume. Compositions of both the modifying additive and concretes based on it were developed. The properties of the mineral modifying additive were studied; mechanochemical activation was applied to increase and modify its activity, and its pozzolanic activity was determined. Depending on the component ratio, CaO absorption ranged from 7.9% to 94%. In the technology of high-strength and functional concretes, high-carbon slag with a fraction of 10–20 mm was used as a partial replacement for natural coarse aggregate. The introduction of 3–15% mineral modifying additive into B40 concrete increased the 28-day compressive strength by 0.19–16%. The greatest increase was observed for concrete containing 8% mineral modifying additive by cement mass. Because compressive strength is not directly correlated with freeze–thaw resistance and water impermeability, capillary suction tests were performed. This non-destructive durability indicator makes it possible to assess concrete permeability, characterize the pore structure, indirectly evaluate freeze–thaw resistance through water-absorption behavior, and estimate the potential resistance of concrete to repeated freezing and thawing. After 24 h, the maximum increase in capillary suction ranged from 4.13% to 5.17%. Direct freeze–thaw testing confirmed a freeze–thaw resistance grade of F400. Three main criteria were used to assign the freeze–thaw resistance grade: average mass loss not exceeding 2%; compliance with the compressive strength ratio XminII >= 0.9 XminI; and the absence of cracks, spalling, and edge-scaling on the specimens.

  • Automated formalization and verification of building code requirements using knowledge graph construction

    by Zarina Kabzhan, Alexandr Shakhnovich, Sergey Gorshkov, Azamat Shakharov, Fedor Gorshkov, Indira Tashmukhanbetova

    Purpose: This study develops and evaluates a methodology for automated formalization and verification of building code requirements using ontology-based knowledge graphs aligned with building information modeling (BIM) data, with the goal of producing executable, traceable, and audit-ready compliance outcomes. Design/methodology/approach: A phased, verification-driven pipeline is proposed that combines ontology engineering with the Lemon/OntoLex specification, direct alignment with the Industry Foundation Classes (IFC) ontology, controlled use of compact large language models (LLMs) for linguistically intensive subtasks, and deterministic generation of executable SPARQL Constraints, Rules, and Functions. End-to-end traceability is implemented through PROV Ontology (PROV-O). Findings: Quantitative and structurally explicit provisions involving numeric thresholds, spatial relations, and aggregations of BIM-derived properties were translated into executable rules. The proof-of-concept evaluation, conducted on accessibility and selected fire-safety clauses from two building codes of the Republic of Kazakhstan, confirms end-to-end executability. Requirements depending on qualitative design intent or modeling conventions not encoded in IFC (e.g. kitchen equipment arrangement) were deliberately flagged as not formalizable rather than translated into speculative rules. Research limitations/implications: The evaluation is illustrative and based on two regulatory clauses; broader empirical validation, quantitative coverage metrics, and cross-jurisdictional generalization remain open. Practical implications: The approach supports transparent digital compliance workflows, enables earlier detection of violations during design, and produces auditable evidence suitable for permitting, supervision, and sustainability reporting. Social implications: Automated and transparent verification of regulatory requirements can improve accountability and consistency in construction project approvals. By enabling auditable compliance checking directly on BIM data, the proposed approach supports safer, more accessible and more inclusive built environments. The methodology can assist public authorities, designers and developers in identifying non-compliant design solutions earlier in the design process, reducing delays and improving regulatory transparency. In the longer term, such digital compliance infrastructures may contribute to more sustainable urban development by strengthening governance mechanisms and supporting evidence-based decision-making in the construction sector. Originality/value: The study contributes a pipeline that combines explicit conceptual–lexical separation, direct IFC alignment, strict confinement of LLMs to interpretation-oriented subtasks, and SPARQL-based executability with provenance traceability. An explicit boundary analysis distinguishes formalizable from non-formalizable requirements–a contribution rarely made explicit in the literature.

  • Open Access

    Mechanochemically Activated Ternary Mineral-Waste Modifier for High-Performance Concrete

    by Ruslan E. Nurlybayev, Axaya S. Yestemessova, Zaure N. Altayeva, Yelzhan S. Orynbekov, Aktota A. Murzagulova, Maxat Z. Bulenbayev, Bakytkul U. Yerkebayeva, Indira B. Tashmukhanbetova

    This article presents the results of a research study on the development and evaluation of a mineral modifying additive for concrete produced from mineral-processing tailings, shale waste from shungite production, and silica fume. Compositions of both the modifying additive and concretes based on it were developed. The properties of the mineral modifying additive were studied; mechanochemical activation was applied to increase and modify its activity, and its pozzolanic activity was determined. Depending on the component ratio, CaO absorption ranged from 7.9% to 94%. In the technology of high-strength and functional concretes, high-carbon slag with a fraction of 10-20 mm was used as a partial replacement for natural coarse aggregate. The introduction of 3-15% mineral modifying additive into B40 concrete increased the 28-day compressive strength by 0.19-16%. The greatest increase was observed for concrete containing 8% mineral modifying additive by cement mass. Because compressive strength is not directly correlated with freeze-thaw resistance and water impermeability, capillary suction tests were performed. This non-destructive durability indicator makes it possible to assess concrete permeability, characterize the pore structure, indirectly evaluate freeze-thaw resistance through water-absorption behavior, and estimate the potential resistance of concrete to repeated freezing and thawing. After 24 h, the maximum increase in capillary suction ranged from 4.13% to 5.17%. Direct freeze-thaw testing confirmed freeze-thaw resistance grade F400. Three main criteria were used to assign the freeze-thaw resistance grade: average mass loss not exceeding 2%, compliance with the compressive-strength ratio XminII >= 0.9 XminI, and absence of cracks, spalling, and edge scaling on the specimens.

  • INVESTIGATION OF THE PROPERTIES OF A WATERBORNE THERMAL INSULATION COMPOSITE BASED ON SHELL LIMESTONE-SHELL ROCK AND HOLLOW MICROSPHERES

    by Y.S. Orynbekov, Z.N. Altayeva, A.S. Yestemessova, R.E. Nurlybayev, V.P. Selyaev, I.B. Tashmukhanbetova, A.N. Alikhan, A.A. Murzagulova

    The aim of this study is to develop a technology for producing a water-dispersion thermal insulation composition based on limestone shell rock mining waste and an acrylate dispersion containing hollow microspheres, as well as to investigate the influence of filled binders on the physical, mechanical, and thermophysical properties of thermal insulation coatings incorporating limestone shell rock from the Zhetybay deposit, Karakiya District, Mangystau Region, Kazakhstan. The microstructure of shell limestone was investigated using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) with a JEOL JSM-7000F scanning electron microscope. The determination of the weight and atomic percentages of the major elements confirmed the carbonate nature of the studied raw material and its consistency with the mineral composition of shell limestone mining waste (wt.%/at.%: O – 50.25/59.34; Ca – 34.14/16.09; C – 15.61/24.56). It was established that, to obtain a water-dispersion composition with low density, it is advisable to use finely dispersed fillers in the form of powder, as well as hollow glass and aluminosilicate microspheres. The particle size of shell limestone powder was 5.67 × 10⁻⁶ m, while the contents of calcium carbonate (CaCO₃) and silica (SiO₂) were 71.0 wt.% and 22.5 wt.%, respectively. A relationship between the proportion and content of shell limestone and microspheres in the filled binder system was identified, demonstrating a significant variation in thermal conductivity within the range of 0.010–0.015 W/(m·°C), as well as changes in the density and adhesive strength of the thermal-insulating coating, reaching ρ₍dry₎ = 0.410–0.415 g/cm³ and σ₍adh₎ ≥ 2.05–2.08 MPa, respectively. The optimal composition of the water-dispersion thermal-insulating coating was determined. The content of the main components is as follows (wt.%): styrene–acrylic or acrylic dispersion, 20–25; shell limestone, 20–25; glass microspheres, 3–9; and aluminosilicate microspheres, 20–30


  • ASSESSMENT OF THE TECHNICAL CONDITION OF CONCRETE AND REINFORCED CONCRETE HYDRAULIC STRUCTURES USING 3D ULTRASONIC TOMOGRAPHY

    by Zh.N. Moldamuratov, K.I. Ilyassova, N.I. Vatin, G.T. Kareken, N.A. Shanshabayev, R.K. Sadyrov, А.а. Bryantsev, I.B. Tashmukhanbetova, A.M. Yessenkeldin

    The article presents the results of assessing the technical condition of the concrete and reinforced concrete structures of the emergency spillway of the Tasotkel Reservoir using the 3D ultrasonic tomography method based on the Betonoskop SK-1700 3D system. The study is aimed at detecting hidden defects, evaluating the internal structure of concrete, and analyzing deterioration processes under long-term seepage, hydrodynamic, and seismic impacts. During the investigation, spatial ultrasonic scanning of a 10×10 m section was performed with a diagnostic depth of up to 0.60 m. Three-dimensional tomographic models, ultrasonic wave velocity distribution maps, vertical and transverse sections, and engineering interpretations of defect zones were developed. It was established that the average ultrasonic wave velocity was approximately 3280 m/s, while minimum values in critically deteriorated areas decreased to 1680-1850 m/s. More than 35% of the investigated structural volume was found to be in a state of severe and critical deterioration, while the proportion of potentially hazardous zones associated with internal voids and loss of bonding accounted for approximately 6-8%. The most critical defects were localized in the lower part of the concrete lining and within the concrete-foundation interface zone, where seepage-induced moisture accumulation, structural loosening, delamination, and local void formation were identified. Correlation analysis confirmed a stable relationship between defect depth and the reduction in ultrasonic wave velocity. The agreement coefficient between the 3D ultrasonic tomography results and visual inspection/local opening investigations ranged from 0.79 to 0.88, while the overall diagnostic reliability reached 91-95%. The obtained results confirm the high efficiency of the Betonoskop SK-1700 3D system for diagnosing hidden defects in concrete and reinforced concrete hydraulic structures and can be applied for inspection, monitoring, and assessment of the operational reliability of hydraulic infrastructure facilities.

  • Open Access

    A Contemporary Ontology-Based Approach to Geotechnical Knowledge Formalization and Regulatory Compliance

    by Zarina Kabzhan, Alexandr Shakhnovich, Sergey Gorshkov, Vitaliy A. Khomyakov, Yusuf Yemenov, Indira Tashmukhanbetova


  • REDUCTION OF SEISMIC EFFECTS ON BUILDINGS USING GEOTECHNICAL SEISMIC ISOLATION

    by R. K. Shegenbayeva, Y.т. Bessimbayev, K. A. Bissenov, I.B. Tashmukhanbetova, S.е. Niyetbay, T. Awwad

    The article addresses one of the most relevant challenges in modern construction–ensuring the reliability and stability of buildings in seismically hazardous regions while reducing the cost of protective engineering measures. The aim of the study is to perform numerical modeling of the influence of geometric and physical–mechanical parameters of geotechnical seismic isolation on the dynamic response of buildings under seismic loading. The study investigates artificial foundation layers composed of sand, pebble gravel, and crushed stone. The scientific novelty lies in substantiating optimal configurations of artificial foundation layers and identifying patterns of seismic response reduction depending on geomaterial characteristics. The interaction between the foundation and the superstructure was simulated using the finite element method in PLAXIS with an earthquake accelerogram as input motion. The results show that increasing the height and volume of the artificial foundation layer reduces horizontal accelerations by approximately 16% at both the foundation and the top of the building. The use of coarse-grained sand led to a reduction in acceleration of up to 15% and foundation settlement of up to 9%, while reinforcement with two geogrid layers further reduced vibration amplitudes by up to 28%. The findings confirm the effectiveness of artificial foundation layers in improving the stability and reliability of buildings in seismic regions.

  • Open Access

    Structure, Synthesis and Properties of Antimony Oxychlorides: A Brief Review

    by Aigul Shongalova, Ainagul Kemelbekova, Arman Umirzakov, Indira Tashmukhanbetova, Elena Dmitriyeva

    Antimony oxychloride compounds represent a distinct class of inorganic materials that combine structural features characteristic of both oxides and halides. Their compositional flexibility and anisotropic properties make them promising candidates for use in photocatalytic systems, optoelectronic devices, flame-retardant coatings, and energy storage technologies. This review provides an overview of the structural characteristics and synthesis strategies associated with key members of the SbxOyClz family, including SbOCl, Sb4O5Cl2, and Sb8O11Cl2. Emphasis is placed on how synthesis parameters—such as temperature, pH, and precursor composition—govern phase formation, morphology, and resulting properties. Recent advances in composite engineering, controlled doping, and surface modification are discussed as effective routes to overcome limitations such as low conductivity and chemical instability. The broader significance of antimony as a strategic element is also addressed in the context of global resource availability and its role in sustainable technologies. Overall, these materials provide a versatile platform for the design of multifunctional systems tailored to meet future demands in materials science and applied engineering.