Abdelkader Bougara
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Abdelkader Bougara has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed Amine Ouared
Laboratory of Structures, Geotechnics and Risks, University of Hassiba Benbouali of Chlef, P.O. Box C 78, Ouled Fares, Chlef 02180, Algeria
2 shared publications - Noureddine Benlakehal
Faculty of Civil Engineering and Architecture, University Hassiba Ben Bouali of Chlef
2 shared publications - Rodica-Mariana Ion
Doctoral School of Engineering Sciences, Valahia University of Târgoviște, 13 Aleea Sinaia, 130004 Targoviste, Romania
2 shared publications - Said Beldjilali
Department of Architecture, University Abed Hamid Iben Badis of Mostaganem, National Road N11, Kharouba, Mostaganem 27000, Algeria
2 shared publications - Abdelkadir Fellouh
Hassiba Benbouali University of Chlef, Chlef, Algeria
1 shared publication - Abdennour Lakhal
Faculty of Civil Engineering and Architecture, University Hassiba Ben Bouali of Chlef
1 shared publication
Latest Publications
- Open Access
Comprehensive Analysis of Gypsum Mortar with Glass Waste Aggregates as a Substitute for Sand
Gypsum has been used as a building material for a long time due to its environmental friendliness, exceptional fire performance, and ease of use. However, it is also known to have poor moisture resistance and lower mechanical performance. Construction and demolition wastes, which can cause many environmental issues if not properly managed, are increasingly recycled as reinforcement materials in gypsum mortar. This study aims to assess the effect of incorporating fine glass waste aggregates into gypsum mortars on their physical, mechanical, and adhesive properties. The effect of replacing sand from 0% to 100% by glass waste in gypsum mortar was investigated using various tests and analyses including scanning electron microscopy (SEM), X-ray diffraction (XRD), thermal analysis (DTA and TGA), setting time, flexural and compressive strengths, adhesive, surface hardness, water absorption, thermal conductivity, and ultrasonic pulse velocity. The results obtained emphasize that glass waste can substitute sand in gypsum mortar, even when used at high replacement levels. Replacing all the sand in mortar with glass waste results in a 11% increase in porosity, a 9% decrease in density, and a 53% decrease in thermal conductivity, while still maintaining acceptable mechanical performances. The adhesive strength shows a great dependence on the nature of the substrate.
Open AccessComprehensive Analysis of Gypsum Mortar with Glass Waste Aggregates as a Substitute for Sand
Gypsum has been used as a building material for a long time due to its environmental friendliness, exceptional fire performance, and ease of use. However, it is also known to have poor moisture resistance and lower mechanical performance. Construction and demolition wastes, which can cause many environmental issues if not properly managed, are increasingly recycled as reinforcement materials in gypsum mortar. This study aims to assess the effect of incorporating fine glass waste aggregates into gypsum mortars on their physical, mechanical, and adhesive properties. The effect of replacing sand from 0% to 100% by glass waste in gypsum mortar was investigated using various tests and analyses including scanning electron microscopy (SEM), X-ray diffraction (XRD), thermal analysis (DTA and TGA), setting time, flexural and compressive strengths, adhesive, surface hardness, water absorption, thermal conductivity, and ultrasonic pulse velocity. The results obtained emphasize that glass waste can substitute sand in gypsum mortar, even when used at high replacement levels. Replacing all the sand in mortar with glass waste results in a 11% increase in porosity, a 9% decrease in density, and a 53% decrease in thermal conductivity, while still maintaining acceptable mechanical performances. The adhesive strength shows a great dependence on the nature of the substrate.
- Open Access
- 18 August 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (16) , 7452
Waste Brick as Partial Replacement of Gypsum in Mortars: Mechanical Performance and Environmental Benefits for Sustainable Construction
Replacing virgin raw materials with recycled waste in construction products is a key strategy for advancing sustainable development. This study explores the partial substitution of commercial gypsum with powdered waste brick (WB) in gypsum mortars, assessing its impact on mechanical performance, water absorption, and environmental footprint. Mortars were prepared with 0%, 5%, 10%, 20%, and 30% WB by weight. Results indicate that a 20% replacement level enhances flexural strength by 56% and compressive strength by 33% at 28 days, compared to the reference mix. SEM and XRD analyses revealed no formation of new crystalline phases, suggesting that the performance improvement is primarily due to physical interactions and microstructural effects. However, at 30% WB, a significant reduction in adhesion strength was observed, falling below the typical threshold for gypsum-based coatings, which may constrain practical application at higher replacement levels. Environmental assessment showed that both CO2 emissions and energy consumption decreased by up to 20% with a 30% substitution. A 20% WB content is therefore proposed as the optimal compromise between mechanical performance and environmental benefit. This approach supports circular economy principles by promoting the reuse of ceramic construction waste in the development of new sustainable materials.
- 18 August 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (16) , 7452
Open AccessWaste Brick as Partial Replacement of Gypsum in Mortars: Mechanical Performance and Environmental Benefits for Sustainable Construction
Replacing virgin raw materials with recycled waste in construction products is a key strategy for advancing sustainable development. This study explores the partial substitution of commercial gypsum with powdered waste brick (WB) in gypsum mortars, assessing its impact on mechanical performance, water absorption, and environmental footprint. Mortars were prepared with 0%, 5%, 10%, 20%, and 30% WB by weight. Results indicate that a 20% replacement level enhances flexural strength by 56% and compressive strength by 33% at 28 days, compared to the reference mix. SEM and XRD analyses revealed no formation of new crystalline phases, suggesting that the performance improvement is primarily due to physical interactions and microstructural effects. However, at 30% WB, a significant reduction in adhesion strength was observed, falling below the typical threshold for gypsum-based coatings, which may constrain practical application at higher replacement levels. Environmental assessment showed that both CO2 emissions and energy consumption decreased by up to 20% with a 30% substitution. A 20% WB content is therefore proposed as the optimal compromise between mechanical performance and environmental benefit. This approach supports circular economy principles by promoting the reuse of ceramic construction waste in the development of new sustainable materials.
- 11 January 2022
- Published by Emerald Publishing in Journal of Structural Fire Engineering
- Vol. 13 (4) , 451-469
Fire resistance of partially encased composite columns subjected to eccentric loading
Purpose: Investigate the fire performance of eccentrically loaded concrete partially encased column (PEC), using the advanced calculation method (ANSYS 18.2, 2017) and the simple calculation method in Annex G of Eurocode 4 (EN 1994-1-2, 2005). This work examines the influence of a range of parameters on fire behaviour of the composite column including: eccentricity loading, slenderness, reinforcement, fire rating and fire scenario. In this study, ISO-834 (ISO834-1, 1999) was used as fire source.Design/methodology/approach: Currently, different methods of analysis used to assess the thermal behaviour of composite column exposed to fire. Analytical method named simplified calculation methods defined in European standard and numerical simulations named advanced calculation models are treated in this paper.Findings: The load-bearing capacity of the composite column becomes very weak in the presence of the fire accident and eccentric loading, this recommends to avoid as much as possible eccentric loading during the design of construction building. The reinforcement has a slight influence on the temperature evolution; moreover, the reinforcement has a great contribution on the load capacity, especially in combined compression and bending. When only the two concrete sides are exposed to fire, the partially encased composite column presents a high load-bearing capacity value.Originality/value: The use of a three-dimensional numerical model (ANSYS) allowed to describe easily the thermal behaviour of PEC columns under eccentric loading with the regard to the analytical method, which is based on three complex steps. In this study, the presence of the load eccentricity has found to have more effect on the load-bearing capacity than the slenderness of the composite column. Introducing a load eccentricity on the top of the column may have the same a reducing effect on the load-bearing capacity as the fire.
- 11 January 2022
- Published by Emerald Publishing in Journal of Structural Fire Engineering
- Vol. 13 (4) , 451-469
Fire resistance of partially encased composite columns subjected to eccentric loading
Purpose: Investigate the fire performance of eccentrically loaded concrete partially encased column (PEC), using the advanced calculation method (ANSYS 18.2, 2017) and the simple calculation method in Annex G of Eurocode 4 (EN 1994-1-2, 2005). This work examines the influence of a range of parameters on fire behaviour of the composite column including: eccentricity loading, slenderness, reinforcement, fire rating and fire scenario. In this study, ISO-834 (ISO834-1, 1999) was used as fire source.Design/methodology/approach: Currently, different methods of analysis used to assess the thermal behaviour of composite column exposed to fire. Analytical method named simplified calculation methods defined in European standard and numerical simulations named advanced calculation models are treated in this paper.Findings: The load-bearing capacity of the composite column becomes very weak in the presence of the fire accident and eccentric loading, this recommends to avoid as much as possible eccentric loading during the design of construction building. The reinforcement has a slight influence on the temperature evolution; moreover, the reinforcement has a great contribution on the load capacity, especially in combined compression and bending. When only the two concrete sides are exposed to fire, the partially encased composite column presents a high load-bearing capacity value.Originality/value: The use of a three-dimensional numerical model (ANSYS) allowed to describe easily the thermal behaviour of PEC columns under eccentric loading with the regard to the analytical method, which is based on three complex steps. In this study, the presence of the load eccentricity has found to have more effect on the load-bearing capacity than the slenderness of the composite column. Introducing a load eccentricity on the top of the column may have the same a reducing effect on the load-bearing capacity as the fire.