N. Pragadish
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
N. Pragadish has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- G. Prabaharan
Department of Mechanical Engineering, SA Engineering College, Chennai, India
1 shared publication - Giridharan Krishnan
Department of Mechanical Engineering, Easwari Engineering College, Chennai, India
1 shared publication - Joshua Gnana Sekaran Jesupadam
Department of Mechanical Engineering CSI College of Engineering Ketti (Ooty) India
1 shared publication - K. Karthikeyan
Department of Mechanical Engineering, Easwari Engineering College, Chennai, India
1 shared publication K. Satish Prakash
Department of Mechanical Engineering, Amrita Sai Institute of Science and Technology, Vijayawada, India
1 shared publication- Lakshmaiya Natrayan
Department of Mechanical Engineering, Saveetha School of Engineering, SIMATS, Chennai, India
1 shared publication
Latest Publications
- 30 October 2026
- Published by Springer Nature in Polymer Bulletin
- Vol. 84 (1) , 1
Enhancing cure, mechanical, and swelling properties of SBR/NBR composites using functionalized halloysite nanotubes
- 30 October 2026
- Published by Springer Nature in Polymer Bulletin
- Vol. 84 (1) , 1
Enhancing cure, mechanical, and swelling properties of SBR/NBR composites using functionalized halloysite nanotubes
- 5 May 2023
- Published by Springer Nature in Silicon
- Vol. 15 (14) , 6033-6046
Effect of Silica Nanoparticles and Modified Silica Nanoparticles on the Mechanical and Swelling Properties of EPDM/SBR Blend Nanocomposites
- 5 May 2023
- Published by Springer Nature in Silicon
- Vol. 15 (14) , 6033-6046
Effect of Silica Nanoparticles and Modified Silica Nanoparticles on the Mechanical and Swelling Properties of EPDM/SBR Blend Nanocomposites
- 20 April 2023
- Published by IOP Publishing in Engineering Research Express
- Vol. 5 (2) , 025019
Characterization of fused deposition modeling components fabricated at different print orientations
The quality of the components fabricated using fusion deposition modelling (FDM) can be tailored by the proper selection of process parameters values. Print orientation is a key process parameter in FDM which has a strong influence on defect formation and thereby mechanical properties of the components. To address the influence of print orientation, FDM of Polyethylene terephthalate glycol (PETG) samples were fabricated and tested. The samples were fabricated using different print orientations namely 0°, 45°, 90° and combination of 45° and 135° alternatively. From the investigation, it was inferred that the print orientation is crucial in deciding the part properties attributing towards the load bearing capacity of print seams. The print orientation of 90° exhibit higher strength by exhibiting peak load values of 942 N and higher elongation of 128 mm. The elongation capability is more than 40 times higher than the 0°, 45°, and 45°/135° orientations which is attributed to the availability of continuous and longer print seam that supports load bearing and elongation.
- 20 April 2023
- Published by IOP Publishing in Engineering Research Express
- Vol. 5 (2) , 025019
Characterization of fused deposition modeling components fabricated at different print orientations
The quality of the components fabricated using fusion deposition modelling (FDM) can be tailored by the proper selection of process parameters values. Print orientation is a key process parameter in FDM which has a strong influence on defect formation and thereby mechanical properties of the components. To address the influence of print orientation, FDM of Polyethylene terephthalate glycol (PETG) samples were fabricated and tested. The samples were fabricated using different print orientations namely 0°, 45°, 90° and combination of 45° and 135° alternatively. From the investigation, it was inferred that the print orientation is crucial in deciding the part properties attributing towards the load bearing capacity of print seams. The print orientation of 90° exhibit higher strength by exhibiting peak load values of 942 N and higher elongation of 128 mm. The elongation capability is more than 40 times higher than the 0°, 45°, and 45°/135° orientations which is attributed to the availability of continuous and longer print seam that supports load bearing and elongation.
- Top Cited Papers
- 17 January 2022
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 13 (15) , 14087-14096
Optimization of cardanol oil dielectric-activated EDM process parameters in machining of silicon steel
- 17 January 2022
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 13 (15) , 14087-14096
Top Cited PapersOptimization of cardanol oil dielectric-activated EDM process parameters in machining of silicon steel