Alessandro Fonte
Research Subjects
Alessandro Fonte has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Antonio A. Traversa
Microwave Components Research and Development Laboratories, SIAE Microelettronica, Milan, Italy
2 shared publications - Luigi Boccia
Dipartimento di Ingegneria Informatica, Modellistica, Elettronica e Sistemistica, University of Calabria, Rende, Italy
2 shared publications - Stefano Moscato
Research and Development Department, Siae Microelettronica, 20093 Cologno Monzese, Italy
2 shared publications Alberto Colzani
R&D Department, SIAE MICROELETTRONICA, Cologno Monzese (MI), Italy
1 shared publication- Alberto Colzani
SIAE Microelettronica,RD Department,Cologno Monzese,Italy
1 shared publication - Alessandro Trifiletti
Department of Information, Electronics and Telecommunications Engineering, Sapienza University, 00184 Roma, Italy
1 shared publication
Latest Publications
- Open Access
- 13 November 2024
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 17 (2) , 177-189
GaN/SiC V-band 10 W high-power amplifier for inter-satellite communications
This manuscript presents a millimeter-wave GaN high-power amplifier (HPA) intended for next generation inter-satellite links (ISLs). The proposed architecture achieves a fractional bandwidth wider than 18% in the V-band spectrum, to deliver a 10 Gbit/s throughput compatible with multi-thousand-km ISLs. Core of the HPA is the monolithic microwave integrated circuits (MMIC ) power amplifier which covers the whole 59–71 GHz band with high efficiency through innovative topologies and a cutting-edge gallium nitride on silicon carbide (GaN-on-SiC) process. The MMIC is then parallelized by means of a 1-to-8 splitter/combiner to obtain a V-band 10 W GaN HPA. Measurement results show a peak small-signal gain of 25.6 dB, 6.5% peak power-added efficiency, and a maximum P1dB of 40.3 dBm.
- 13 November 2024
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 17 (2) , 177-189
Open AccessGaN/SiC V-band 10 W high-power amplifier for inter-satellite communications
This manuscript presents a millimeter-wave GaN high-power amplifier (HPA) intended for next generation inter-satellite links (ISLs). The proposed architecture achieves a fractional bandwidth wider than 18% in the V-band spectrum, to deliver a 10 Gbit/s throughput compatible with multi-thousand-km ISLs. Core of the HPA is the monolithic microwave integrated circuits (MMIC ) power amplifier which covers the whole 59–71 GHz band with high efficiency through innovative topologies and a cutting-edge gallium nitride on silicon carbide (GaN-on-SiC) process. The MMIC is then parallelized by means of a 1-to-8 splitter/combiner to obtain a V-band 10 W GaN HPA. Measurement results show a peak small-signal gain of 25.6 dB, 6.5% peak power-added efficiency, and a maximum P1dB of 40.3 dBm.
- Open Access
- 22 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (6) , 2582-2593
Flippable and Hermetic E-Band RWG to GCPW Transition With Substrate Embedded Backshort
In this article, a novel millimeter wave (mm-wave), fully hermetic and flippable transitioning structure between grounded coplanar waveguides (GCPWs) and rectangular waveguides (RWGs) is introduced. This transition, realized through standard printed circuit board (PCB) technology, can be employed to feed a waveguide (WG) compliant device on any face of a board given its flexibility in trace routing and component placement. The proposed structure utilizes a mix of transmission line and substrate integrated waveguide (SIW) interconnected with an in-substrate embedded back-short. The transition, in all its configurations, targets a fractional bandwidth (FBW) wider than 20% to cover the commercial $E$ -band spectrum. Moreover, at center frequency the predicted insertion loss (IL) for both normal and flipped transitions is 0.4 and 0.46 dB, respectively. Parametric and yield analyses, together with postmanufacturing inspections have been performed to assess the robustness of the design and to identify the critical manufacturing inaccuracies. The experimental validations confirm the wideband operation with an IL bounded below 2.3 dB for the worst case of a back-to-back configuration.
- 22 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (6) , 2582-2593
Open AccessFlippable and Hermetic E-Band RWG to GCPW Transition With Substrate Embedded Backshort
In this article, a novel millimeter wave (mm-wave), fully hermetic and flippable transitioning structure between grounded coplanar waveguides (GCPWs) and rectangular waveguides (RWGs) is introduced. This transition, realized through standard printed circuit board (PCB) technology, can be employed to feed a waveguide (WG) compliant device on any face of a board given its flexibility in trace routing and component placement. The proposed structure utilizes a mix of transmission line and substrate integrated waveguide (SIW) interconnected with an in-substrate embedded back-short. The transition, in all its configurations, targets a fractional bandwidth (FBW) wider than 20% to cover the commercial $E$ -band spectrum. Moreover, at center frequency the predicted insertion loss (IL) for both normal and flipped transitions is 0.4 and 0.46 dB, respectively. Parametric and yield analyses, together with postmanufacturing inspections have been performed to assess the robustness of the design and to identify the critical manufacturing inaccuracies. The experimental validations confirm the wideband operation with an IL bounded below 2.3 dB for the worst case of a back-to-back configuration.
- 9 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
SiGe BiCMOS building blocks for a K/Ka-band flexible phased array system for SatCom applications
This work reports the design of two key building blocks of a K/Ka-band SatCom phased-array transceiver. The circuits are developed by using 130-nm SiGe:C BiCMOS technology. A Ka-band single-ended Power Amplifier (PA) and a K-band single-ended Low-Noise Amplifier (LNA) have been designed. Simulation results have shown that the PA achieves 30.5 dB peak small signal gain, 27.6% peak power added efficiency (PAE), and an OIP3 better than 25 dBm within the entire operating frequency band. The maximum power consumption is 76 mW with a 2 V supply voltage, and it occupies an area of $1234\ \mu\mathrm{m}\times 758\ \mu\mathrm{m}$ , pads included. The simulations results of the LNA have shown 32 dB peak power gain, 2 dB minimum noise figure, and −18 dBm IIP3 at 20 GHz. The NF, in the entire frequency band of interest, is less than 2.3 dB. The LNA exhibits a power consumption of 20.7 mW with a supply voltage of 2.4 V and it occupies an area of $1000\ \mu\mathrm{m}\times 800\ \mu\mathrm{m}$ , pads included. It is worth noting that, a set of test structures that includes all the HBTs used for PA and LNA development have been designed and measured in order to evaluate both the accuracy of the models provided by the foundry and the impact of the extrinsic elements due to base, collector, and emitter interconnections.- 9 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
SiGe BiCMOS building blocks for a K/Ka-band flexible phased array system for SatCom applications
This work reports the design of two key building blocks of a K/Ka-band SatCom phased-array transceiver. The circuits are developed by using 130-nm SiGe:C BiCMOS technology. A Ka-band single-ended Power Amplifier (PA) and a K-band single-ended Low-Noise Amplifier (LNA) have been designed. Simulation results have shown that the PA achieves 30.5 dB peak small signal gain, 27.6% peak power added efficiency (PAE), and an OIP3 better than 25 dBm within the entire operating frequency band. The maximum power consumption is 76 mW with a 2 V supply voltage, and it occupies an area of $1234\ \mu\mathrm{m}\times 758\ \mu\mathrm{m}$ , pads included. The simulations results of the LNA have shown 32 dB peak power gain, 2 dB minimum noise figure, and −18 dBm IIP3 at 20 GHz. The NF, in the entire frequency band of interest, is less than 2.3 dB. The LNA exhibits a power consumption of 20.7 mW with a supply voltage of 2.4 V and it occupies an area of $1000\ \mu\mathrm{m}\times 800\ \mu\mathrm{m}$ , pads included. It is worth noting that, a set of test structures that includes all the HBTs used for PA and LNA development have been designed and measured in order to evaluate both the accuracy of the models provided by the foundry and the impact of the extrinsic elements due to base, collector, and emitter interconnections.- 13 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (9) , 3098-3102
Compact E-Band I/Q Receiver in SiGe BiCMOS for 5G Backhauling Applications
The implementation of backhauling links poses several challenges to the designers which are requested to limit the hardware costs in the framework of complex millimeter wave radio systems. This work presents a monolithically integrated E-band I/Q receiver covering the whole bandwidth from 71 to 86 GHz. The chip was implemented in a 55 nm SiGe BiCMOS technology which allows reaching a high level of integration. The receiver is based on a Low Noise Amplifier (LNA) stage and a Variable-Gain Amplifier (VGA) which provide a -11 dBm IP1dB. A double balanced mixer provides I/Q baseband outputs through a reduced-size differential phase shifter which allows to contain the chip size to 1.8 mm 2 .
- 13 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (9) , 3098-3102
Compact E-Band I/Q Receiver in SiGe BiCMOS for 5G Backhauling Applications
The implementation of backhauling links poses several challenges to the designers which are requested to limit the hardware costs in the framework of complex millimeter wave radio systems. This work presents a monolithically integrated E-band I/Q receiver covering the whole bandwidth from 71 to 86 GHz. The chip was implemented in a 55 nm SiGe BiCMOS technology which allows reaching a high level of integration. The receiver is based on a Low Noise Amplifier (LNA) stage and a Variable-Gain Amplifier (VGA) which provide a -11 dBm IP1dB. A double balanced mixer provides I/Q baseband outputs through a reduced-size differential phase shifter which allows to contain the chip size to 1.8 mm 2 .
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 57-60
5G 26 GHz and 28 GHz Bands SiGe:C Receiver with Very High-Linearity and 56 dB Dynamic Range
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 57-60
5G 26 GHz and 28 GHz Bands SiGe:C Receiver with Very High-Linearity and 56 dB Dynamic Range
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2004, 160-163
Design of a Low Noise Amplifier with integrated antenna for 60 GHz wireless communications
The integration of a Low Noise Amplifier (LNA) with on-chip antenna for 60 GHz short-range wireless applications is discussed in the paper. A 65 nm CMOS Silicon-on-Insulator (SOI) technology has been selected as target. With respect to the state of the art, the on-chip co-design of LNA and antenna permits avoiding a pre-defined constraint of 50 Ohm impedance matching. By relaxing the impedance matching specification a LNA with only two amplification stages has been designed to reach the desired power gain (>;20 dB) and noise figure (<; 5 dB) with a power consumption and circuit complexity optimized vs. state-of-art LNAs with similar performances. A dipole antenna with coplanar strip feed has been also designed matching the 20 Ohm input LNA impedance and allowing an extra gain of 3 dB at 60 GHz with a limited on-chip area occupation.
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2004, 160-163
Design of a Low Noise Amplifier with integrated antenna for 60 GHz wireless communications
The integration of a Low Noise Amplifier (LNA) with on-chip antenna for 60 GHz short-range wireless applications is discussed in the paper. A 65 nm CMOS Silicon-on-Insulator (SOI) technology has been selected as target. With respect to the state of the art, the on-chip co-design of LNA and antenna permits avoiding a pre-defined constraint of 50 Ohm impedance matching. By relaxing the impedance matching specification a LNA with only two amplification stages has been designed to reach the desired power gain (>;20 dB) and noise figure (<; 5 dB) with a power consumption and circuit complexity optimized vs. state-of-art LNAs with similar performances. A dipole antenna with coplanar strip feed has been also designed matching the 20 Ohm input LNA impedance and allowing an extra gain of 3 dB at 60 GHz with a limited on-chip area occupation.
- 23 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 19 (7) , 461-463
Microwave Active Inductors
In this letter, the experimental proofs of two microwave active inductors with very high quality factor, namely Differential Boot-Strapped Inductor (D-BSI) and Cross-Coupled Differential Boot-Strapped Inductor (CCD-BSI), are presented. These circuits can be effectively implemented in modern RF-CMOS processes for high-Q equivalent integrated inductors at high frequency. The cases of study at 13 GHz have been designed and implemented in a modern standard 90 nm bulk CMOS process. The measurements on the test-chips show an equivalent inductance close to 3.2 nH with an associated quality factor up to 400 and a wide linearity range.
- 23 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 19 (7) , 461-463
Microwave Active Inductors
In this letter, the experimental proofs of two microwave active inductors with very high quality factor, namely Differential Boot-Strapped Inductor (D-BSI) and Cross-Coupled Differential Boot-Strapped Inductor (CCD-BSI), are presented. These circuits can be effectively implemented in modern RF-CMOS processes for high-Q equivalent integrated inductors at high frequency. The cases of study at 13 GHz have been designed and implemented in a modern standard 90 nm bulk CMOS process. The measurements on the test-chips show an equivalent inductance close to 3.2 nH with an associated quality factor up to 400 and a wide linearity range.