Huseyin Yilmaz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Huseyin Yilmaz has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Murat Murutoglu
Renewable Energy Technologies Group, Engineering Materials Science, Faculty of Engineering and Natural Sciences, Tampere University, 33720 Tampere, Finland
7 shared publications - Buse Bilbey
Renewable Energy Technologies Group, Engineering Materials Science, Faculty of Engineering and Natural Sciences, Tampere University, 33720 Tampere, Finland
4 shared publications - Muhammad Imran Asghar
Renewable Energy Technologies Group, Engineering Materials Science, Faculty of Engineering and Natural Sciences Tampere University Tampere Finland
4 shared publications - Aligul Buyukaksoy
Department of Materials Science and Engineering Gebze Technical University Kocaeli Turkey
3 shared publications Aygul Alkan Gultekin
3 shared publicationsUgur Ozsarac
3 shared publications
Latest Publications
- 14 May 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 682
Single-step fabrication of a three-layered full solid oxide fuel cells via the cold sintering process
- 14 May 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 682
Single-step fabrication of a three-layered full solid oxide fuel cells via the cold sintering process
- Open Access
Is Super-Duplex Stainless Steel Suitable as Metal Support for Solid Oxide Cells?
In this study, commercial Ospray-2507 super-duplex stainless steel powder was investigated for the first time as a potential metal support material for solid oxide cells. Initially, metal supports were fabricated and processed in air using various sintering profiles, followed by comprehensive mechanical, structural and electrochemical characterization. The optimal sintering condition was identified as 900 °C for 5 h. Subsequently, sintering under a H2 atmosphere was explored, and its effects on the microstructural and functional properties of the metal supports were systematically to assessed to evaluate the influence of the sintering atmosphere on material performance. Although X-ray diffraction patterns showed no phase changes between the two sintering atmospheres, notable improvements were observed in mechanical, electrochemical, and microstructural properties under H2 sintering. XPS spectra reveal that both air- and hydrogen-treated surfaces remain rich in chromium (Cr) and Manganese (Mn), which together dominate the surface and consequently attenuate the signal from the underlying iron. The thickness of the Cr- and Mn-based oxide layer decreases when sintering MS in H2 atmosphere. Specifically, mechanical strength, as measured by three-point bending tests, increased by a factor of 12.5, and hardness rose from 500.3 to 523.5 HV. Furthermore, electrical conductivity also improved significantly, exhibiting an approximately 2.3–2.4 fold increase under H2-sintered conditions.
Open AccessIs Super-Duplex Stainless Steel Suitable as Metal Support for Solid Oxide Cells?
In this study, commercial Ospray-2507 super-duplex stainless steel powder was investigated for the first time as a potential metal support material for solid oxide cells. Initially, metal supports were fabricated and processed in air using various sintering profiles, followed by comprehensive mechanical, structural and electrochemical characterization. The optimal sintering condition was identified as 900 °C for 5 h. Subsequently, sintering under a H2 atmosphere was explored, and its effects on the microstructural and functional properties of the metal supports were systematically to assessed to evaluate the influence of the sintering atmosphere on material performance. Although X-ray diffraction patterns showed no phase changes between the two sintering atmospheres, notable improvements were observed in mechanical, electrochemical, and microstructural properties under H2 sintering. XPS spectra reveal that both air- and hydrogen-treated surfaces remain rich in chromium (Cr) and Manganese (Mn), which together dominate the surface and consequently attenuate the signal from the underlying iron. The thickness of the Cr- and Mn-based oxide layer decreases when sintering MS in H2 atmosphere. Specifically, mechanical strength, as measured by three-point bending tests, increased by a factor of 12.5, and hardness rose from 500.3 to 523.5 HV. Furthermore, electrical conductivity also improved significantly, exhibiting an approximately 2.3–2.4 fold increase under H2-sintered conditions.
- Open Access
- 13 March 2026
- Published by Elsevier in SSRN Electronic Journal
Single-Step Fabrication of a Three-Layered Full Solid Oxide Fuel Cells via the Cold Sintering Process
Nanocomposite electrolytes based on Sm-doped ceria and sodium carbonates emerge as promising candidates for intermediate-temperature solid oxide fuel cells (IT-SOFCs) due to their exceptional ionic conductivity. However, conventional high-temperature sintering presents challenges regarding cost, phase stability, and insufficient densification. This study presents a pioneering approach for the fabrication of a full, three-layered SOFC (anode/electrolyte/cathode) in a single step using the cold sintering process at a remarkably low temperature of 200°C. Two different preparation methods for the electrolyte, co-precipitation and direct solid-state mixing, undergo investigation. While both methods yield comparable conductivity values around 140 mS.cm⁻¹ at 600°C in H₂ atmosphere, the direct mixing route offers superior densification (>97%) and serves as the chosen method for full-cell fabrication. This work reports the electrochemical performance of a full SOFC fabricated in a single step via cold sintering for the first time. Electrochemical impedance spectroscopy reveals a low ohmic resistance of 0.15 Ω.cm², confirming the efficacy of this process in preserving the nanostructure and facilitating superionic conduction. A peak power density of 534 mW.cm⁻² validates this method as an energy-efficient, scalable solution for IT-SOFC production.
- 13 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSingle-Step Fabrication of a Three-Layered Full Solid Oxide Fuel Cells via the Cold Sintering Process
Nanocomposite electrolytes based on Sm-doped ceria and sodium carbonates emerge as promising candidates for intermediate-temperature solid oxide fuel cells (IT-SOFCs) due to their exceptional ionic conductivity. However, conventional high-temperature sintering presents challenges regarding cost, phase stability, and insufficient densification. This study presents a pioneering approach for the fabrication of a full, three-layered SOFC (anode/electrolyte/cathode) in a single step using the cold sintering process at a remarkably low temperature of 200°C. Two different preparation methods for the electrolyte, co-precipitation and direct solid-state mixing, undergo investigation. While both methods yield comparable conductivity values around 140 mS.cm⁻¹ at 600°C in H₂ atmosphere, the direct mixing route offers superior densification (>97%) and serves as the chosen method for full-cell fabrication. This work reports the electrochemical performance of a full SOFC fabricated in a single step via cold sintering for the first time. Electrochemical impedance spectroscopy reveals a low ohmic resistance of 0.15 Ω.cm², confirming the efficacy of this process in preserving the nanostructure and facilitating superionic conduction. A peak power density of 534 mW.cm⁻² validates this method as an energy-efficient, scalable solution for IT-SOFC production.
- Open Access
- 23 December 2025
- Published by Wiley in International Journal of Ceramic Engineering & Science
- Vol. 8 (1)
Interparticle Forces Behind Plasticity of Ceramic Pastes: A Literature Review
Plastic‐forming methods of ceramic pastes, such as extrusion, have been significant in the ceramics industry for many years. Despite its significance, the plasticity of ceramic pastes is poorly understood. It is essential to understand the fundamentals of ceramic paste plasticity to develop a forming technology with superior performance. The ceramic pastes’ plasticity can be characterized by the co‐existence of apparently opposing properties, that is, “flowability” and “rigidity.” It has been claimed that the apparently opposing properties can be achieved by controlling the interparticle interaction that is attractive at long range and repulsive at short range. The present article aims to verify the model based on experimental results from interaction force measurements. The interaction forces are gathered by the atomic force microscope (AFM) colloid probe technique. On the basis of the discussion, it is concluded that the above microscopic model is available to interpret ceramic pastes’ macroscopic behaviors.
- 23 December 2025
- Published by Wiley in International Journal of Ceramic Engineering & Science
- Vol. 8 (1)
Open AccessInterparticle Forces Behind Plasticity of Ceramic Pastes: A Literature Review
Plastic‐forming methods of ceramic pastes, such as extrusion, have been significant in the ceramics industry for many years. Despite its significance, the plasticity of ceramic pastes is poorly understood. It is essential to understand the fundamentals of ceramic paste plasticity to develop a forming technology with superior performance. The ceramic pastes’ plasticity can be characterized by the co‐existence of apparently opposing properties, that is, “flowability” and “rigidity.” It has been claimed that the apparently opposing properties can be achieved by controlling the interparticle interaction that is attractive at long range and repulsive at short range. The present article aims to verify the model based on experimental results from interaction force measurements. The interaction forces are gathered by the atomic force microscope (AFM) colloid probe technique. On the basis of the discussion, it is concluded that the above microscopic model is available to interpret ceramic pastes’ macroscopic behaviors.
- Open Access
- 24 October 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (29) , 60993-61002
Carbonate content and solvent effects on microstructural and electrical properties of cold sintered SDC-Na2CO3 nanocomposite electrolytes
- 24 October 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (29) , 60993-61002
Open AccessCarbonate content and solvent effects on microstructural and electrical properties of cold sintered SDC-Na2CO3 nanocomposite electrolytes
- 4 November 2023
- Published by Elsevier in Ceramics International
- Vol. 50 (2) , 2901-2908
Mechanical properties of 3D-printed Al2O3 honeycomb sandwich structures prepared using the SLA method with different core geometries
- 4 November 2023
- Published by Elsevier in Ceramics International
- Vol. 50 (2) , 2901-2908
Mechanical properties of 3D-printed Al2O3 honeycomb sandwich structures prepared using the SLA method with different core geometries
- Open Access
- 4 July 2023
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 106 (11) , 6441-6453
One step densification of SDC—Na2CO3 nano‐composite electrolytes for SOFC applications by cold sintering process
Sm0.2Ce0.8O1.9‐ 30% Na2CO3 (Sm doped ceria (SDC)‐30N) nano‐composite electrolytes were densified in a single step via cold sintering process (CSP). At 200°C and 450 MPa of uniaxial pressure, samples up to 97% of their theoretical density could be obtained. The effect of processing parameters, such as temperature, uniaxial pressure, processing duration, and moisture content, on the densification of the nano‐composite electrolytes was investigated. The thermal, microstructural, and electrical properties of nano‐composites were investigated by differential scanning calorimetry, X‐ray diffractometer, scanning electron microscope, and EIS analysis. SDC crystallite sizes were found to be around 25 nm, barely coarsened after CSP by which the true nano nature of the nano‐composite could be preserved. Because, by conventional processing high density values could not be attained and high processing temperatures in excess of 600°C had to be used, promoting particle coarsening. The highest total electrical conductivity was found to be 2.2 × 10−2 S cm−1 at 600°C, with an activation energy of 0.83 eV for SDC‐30N nano‐composites. The present investigation revealed that the implementation of cold sintering technique resulted in significant enhancements in the densification of nano‐composite electrolytes, thereby rendering them suitable for efficient utilization in SOFC applications, as compared to the conventional production methods.
- 4 July 2023
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 106 (11) , 6441-6453
Open AccessOne step densification of SDC—Na2CO3 nano‐composite electrolytes for SOFC applications by cold sintering process
Sm0.2Ce0.8O1.9‐ 30% Na2CO3 (Sm doped ceria (SDC)‐30N) nano‐composite electrolytes were densified in a single step via cold sintering process (CSP). At 200°C and 450 MPa of uniaxial pressure, samples up to 97% of their theoretical density could be obtained. The effect of processing parameters, such as temperature, uniaxial pressure, processing duration, and moisture content, on the densification of the nano‐composite electrolytes was investigated. The thermal, microstructural, and electrical properties of nano‐composites were investigated by differential scanning calorimetry, X‐ray diffractometer, scanning electron microscope, and EIS analysis. SDC crystallite sizes were found to be around 25 nm, barely coarsened after CSP by which the true nano nature of the nano‐composite could be preserved. Because, by conventional processing high density values could not be attained and high processing temperatures in excess of 600°C had to be used, promoting particle coarsening. The highest total electrical conductivity was found to be 2.2 × 10−2 S cm−1 at 600°C, with an activation energy of 0.83 eV for SDC‐30N nano‐composites. The present investigation revealed that the implementation of cold sintering technique resulted in significant enhancements in the densification of nano‐composite electrolytes, thereby rendering them suitable for efficient utilization in SOFC applications, as compared to the conventional production methods.
- Open Access
- 1 January 2023
- Published by Elsevier in SSRN Electronic Journal
One Step Densification of Sdc – Na2co3 Nano-Composite Electrolytes for Advanced Ltsofc Applications by Cold Sintering Process
Sm0.2Ce0.8O1.9- 30% Na2CO3 (SDC-30N) nano-composite electrolytes were densified in a single step via cold sintering process (CSP). At 200 °C and 300 MPa of uniaxial pressure, samples up to 97% of their theoretical density could be obtained. The effect of processing parameters, such as temperature, uniaxial pressure, processing duration, and moisture content, on the densification of the nano-composite electrolytes was investigated. The thermal, microstructural, and electrical properties of nano-composites were investigated by DSC, XRD, SEM, and EIS analysis. SDC crystallite sizes were found to be around 25 nm, barely coarsened after CSP by which the true nano nature of the nano-composite could be preserved. Because, by conventional processing high density values could not be attained and high processing temperatures in excess of 600 °C had to be used, promoting particle coarsening. The highest total electrical conductivity was found to be 3.8x10-3 S·cm−1 with an activation energy of 1.16 eV for SDC-30N nanocomposites.
- 1 January 2023
- Published by Elsevier in SSRN Electronic Journal
Open AccessOne Step Densification of Sdc – Na2co3 Nano-Composite Electrolytes for Advanced Ltsofc Applications by Cold Sintering Process
Sm0.2Ce0.8O1.9- 30% Na2CO3 (SDC-30N) nano-composite electrolytes were densified in a single step via cold sintering process (CSP). At 200 °C and 300 MPa of uniaxial pressure, samples up to 97% of their theoretical density could be obtained. The effect of processing parameters, such as temperature, uniaxial pressure, processing duration, and moisture content, on the densification of the nano-composite electrolytes was investigated. The thermal, microstructural, and electrical properties of nano-composites were investigated by DSC, XRD, SEM, and EIS analysis. SDC crystallite sizes were found to be around 25 nm, barely coarsened after CSP by which the true nano nature of the nano-composite could be preserved. Because, by conventional processing high density values could not be attained and high processing temperatures in excess of 600 °C had to be used, promoting particle coarsening. The highest total electrical conductivity was found to be 3.8x10-3 S·cm−1 with an activation energy of 1.16 eV for SDC-30N nanocomposites.
- 22 January 2022
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 47 (45) , 19772-19779
Cold sintering-assisted densification of GDC electrolytes for SOFC applications
- 22 January 2022
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 47 (45) , 19772-19779
Cold sintering-assisted densification of GDC electrolytes for SOFC applications
- Open Access
- 1 January 2018
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 12 (2) , 123-128
Processing and mechanical characterization of Al2O3/Ni and Al2O3/C0 composites by pressureless sintering of nanocomposite powders
Al2O3/Ni and Al2O3/Co nanopowder mixtures (with 3 vol.% of metallic phase) were synthesized by heterogeneous precipitation method. In order to increase the green strength, polypropylene carbonate (PPC) was used as a binder while preparing green compacts. Uniaxially pressed powder mixtures were sintered at 1550°C for 2 h in a reducing atmosphere. The effects of Ni and Co nanophases on the microstructure and mechanical properties of Al2O3 ceramics were studied by X-ray diffraction, scanning electron microscopy, Vickers indentation technique and three-point bending tests. The metallic phase hindered the densification of alumina matrix, yet hardness values of Al2O3, Al2O3/Ni, and Al2O3/Co composites were comparable. Vickers fracture toughness results indicate that the composites have higher fracture toughness, but the characteristic flexural strength and Weibull modulus are higher for the pure Al2O3.
- 1 January 2018
- Published by National Library of Serbia in Processing and Application of Ceramics
- Vol. 12 (2) , 123-128
Open AccessProcessing and mechanical characterization of Al2O3/Ni and Al2O3/C0 composites by pressureless sintering of nanocomposite powders
Al2O3/Ni and Al2O3/Co nanopowder mixtures (with 3 vol.% of metallic phase) were synthesized by heterogeneous precipitation method. In order to increase the green strength, polypropylene carbonate (PPC) was used as a binder while preparing green compacts. Uniaxially pressed powder mixtures were sintered at 1550°C for 2 h in a reducing atmosphere. The effects of Ni and Co nanophases on the microstructure and mechanical properties of Al2O3 ceramics were studied by X-ray diffraction, scanning electron microscopy, Vickers indentation technique and three-point bending tests. The metallic phase hindered the densification of alumina matrix, yet hardness values of Al2O3, Al2O3/Ni, and Al2O3/Co composites were comparable. Vickers fracture toughness results indicate that the composites have higher fracture toughness, but the characteristic flexural strength and Weibull modulus are higher for the pure Al2O3.