Jin-Gyun Chung
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jin-Gyun Chung has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Samuel Woo
Department of Software Science, Dankook University, Yongin 16890, Republic of Korea
4 shared publications - Dong-Hyun Seo
Green Mobility R&D Center, Jeonbuk Institute of Automotive Convergence Technology, Gunsan 573450, Republic of Korea
2 shared publications - Moon Ho Lee
Chonbuk National University
2 shared publications - Shi-Yi Jin
Division of Electronic Engineering, IT Convergence Research Center, Jeonbuk National University, Jeonju 54896, Republic of Korea
2 shared publications - Yeon-Jin Kim
Division of Electronic Engineering, IT Convergence Research Center, Jeonbuk National University, Jeonju 54896, Republic of Korea
2 shared publications - Abdul Latif Sarker
Department of Electronics and Information Engineering, Jeonbuk National University, Jeonju, South Korea
1 shared publication
Latest Publications
- Open Access
- 28 February 2024
- Published by MDPI AG in Information
- Vol. 15 (3) , 132
Single-Frame-Based Data Compression for CAN Security
To authenticate a controller area network (CAN) data frame, a message authentication code (MAC) must be sent along with the CAN frame, but there is no space reserved for the MAC in the CAN frame. Recently, difference-based compression (DBC) algorithms have been used to create a space inside the frame. DBC has the advantage of being very efficient, but its drawback is that, if an error occurs in one frame, the effects of that error propagate to subsequent frames. In this paper, a CAN data compression algorithm is proposed that compresses the current frame without relying on previous frames. Therefore, an error generated in one frame cannot be propagated to subsequent frames. In addition, a CAN signal grouping technique is proposed based on entropy analysis. To efficiently authenticate CAN frames, the length of the compressed data must be 4 bytes or less (4BL). Simulation shows that the 4BL-compression ratio of a Kia Sorento vehicle is 99.36% in the DBC method, but 100% in the proposed method. In an LS Mtron tractor, the 4BL-compression ratio is 98.58% in the DBC method, but 100% in the proposed method. In addition, the execution time of the proposed compression algorithm is only 27.39% of that of the DBC algorithm. The results show that the proposed algorithm has better compression characteristics for CAN security than the DBC algorithms.
- 28 February 2024
- Published by MDPI AG in Information
- Vol. 15 (3) , 132
Open AccessSingle-Frame-Based Data Compression for CAN Security
To authenticate a controller area network (CAN) data frame, a message authentication code (MAC) must be sent along with the CAN frame, but there is no space reserved for the MAC in the CAN frame. Recently, difference-based compression (DBC) algorithms have been used to create a space inside the frame. DBC has the advantage of being very efficient, but its drawback is that, if an error occurs in one frame, the effects of that error propagate to subsequent frames. In this paper, a CAN data compression algorithm is proposed that compresses the current frame without relying on previous frames. Therefore, an error generated in one frame cannot be propagated to subsequent frames. In addition, a CAN signal grouping technique is proposed based on entropy analysis. To efficiently authenticate CAN frames, the length of the compressed data must be 4 bytes or less (4BL). Simulation shows that the 4BL-compression ratio of a Kia Sorento vehicle is 99.36% in the DBC method, but 100% in the proposed method. In an LS Mtron tractor, the 4BL-compression ratio is 98.58% in the DBC method, but 100% in the proposed method. In addition, the execution time of the proposed compression algorithm is only 27.39% of that of the DBC algorithm. The results show that the proposed algorithm has better compression characteristics for CAN security than the DBC algorithms.
- 14 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 72 (12) , 15154-15171
Real Time Perfect Bit Modification Attack on In-Vehicle CAN
The vulnerabilities of controller area network (CAN) are often targeted by various types of vehicle hacking. To this end, conventional cyber attacks have used a frame injection and a dominant bit injection. However, these two techniques cannot modify data frames sent from an electronic control unit (ECU) in real time. Thus, the frame injection cannot perfectly control the target system. The dominant bit injection can only perform denial of service (DoS) attacks, which means that it cannot perfectly control the ECU. In this paper, we propose a new attack technique for modifying either dominant or recessive bits represented in a CAN bus as the attacker intends. This technique is called perfect bit modification (PBM). We introduce two attack models using the PBM technique, the bus possession attack (BPA) and the target ID attack (TIA). The BPA can perform an attack without breaking the communication pattern of the CAN bus, and the TIA can perfectly seize control of a specific ECU. In addition, we produce an attack tool with the PBM functionality using the SN65HVD230 (CAN transceiver) and the FDS8949 (MOSFET). Both SN65HVD230 and FDS8949 are components that are commonly used to build ECUs, which cost less than two dollars. This means that our attack models are likely to be utilized for supply chain attacks. To demonstrate the feasibility of BPA and TIA, we conduct attack experiments using two real vehicles. Finally, we analyze the characteristics of existing attack techniques including PBM and suggest countermeasures to construct a secure CAN environment.
- 14 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 72 (12) , 15154-15171
Real Time Perfect Bit Modification Attack on In-Vehicle CAN
The vulnerabilities of controller area network (CAN) are often targeted by various types of vehicle hacking. To this end, conventional cyber attacks have used a frame injection and a dominant bit injection. However, these two techniques cannot modify data frames sent from an electronic control unit (ECU) in real time. Thus, the frame injection cannot perfectly control the target system. The dominant bit injection can only perform denial of service (DoS) attacks, which means that it cannot perfectly control the ECU. In this paper, we propose a new attack technique for modifying either dominant or recessive bits represented in a CAN bus as the attacker intends. This technique is called perfect bit modification (PBM). We introduce two attack models using the PBM technique, the bus possession attack (BPA) and the target ID attack (TIA). The BPA can perform an attack without breaking the communication pattern of the CAN bus, and the TIA can perfectly seize control of a specific ECU. In addition, we produce an attack tool with the PBM functionality using the SN65HVD230 (CAN transceiver) and the FDS8949 (MOSFET). Both SN65HVD230 and FDS8949 are components that are commonly used to build ECUs, which cost less than two dollars. This means that our attack models are likely to be utilized for supply chain attacks. To demonstrate the feasibility of BPA and TIA, we conduct attack experiments using two real vehicles. Finally, we analyze the characteristics of existing attack techniques including PBM and suggest countermeasures to construct a secure CAN environment.
- Open Access
- 18 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2654
MAC-Based Compression Ratio Improvement for CAN Security
Information security in a controller area network (CAN) is becoming more important as the connections between a vehicle’s internal and external networks increase. Encryption and authentication techniques can be applied to CAN data frames to enhance security. To authenticate a data frame, a message authentication code (MAC) needs to be transmitted with the CAN data frame. Therefore, space for transmitting the MAC is required within the CAN frame. Recently, the Triple ID algorithm has been proposed to create additional space in the data field of the CAN frame. The Triple ID algorithm ensures every CAN frame is authenticated by at least 4 bytes of MAC without changing the original CAN protocol. However, since the Triple ID algorithm uses six header bits, there is a problem associated with low data compression efficiency. In this paper, we propose an algorithm that can remove up to 15 bits from frames compressed with the Triple ID algorithm. Through simulation using CAN signals of a Kia Sorento vehicle and an LS Mtron tractor, we show that the generation of frames containing compressed messages of 4 bytes or more is reduced by up to 99.57% compared to the Triple ID method.
- 18 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2654
Open AccessMAC-Based Compression Ratio Improvement for CAN Security
Information security in a controller area network (CAN) is becoming more important as the connections between a vehicle’s internal and external networks increase. Encryption and authentication techniques can be applied to CAN data frames to enhance security. To authenticate a data frame, a message authentication code (MAC) needs to be transmitted with the CAN data frame. Therefore, space for transmitting the MAC is required within the CAN frame. Recently, the Triple ID algorithm has been proposed to create additional space in the data field of the CAN frame. The Triple ID algorithm ensures every CAN frame is authenticated by at least 4 bytes of MAC without changing the original CAN protocol. However, since the Triple ID algorithm uses six header bits, there is a problem associated with low data compression efficiency. In this paper, we propose an algorithm that can remove up to 15 bits from frames compressed with the Triple ID algorithm. Through simulation using CAN signals of a Kia Sorento vehicle and an LS Mtron tractor, we show that the generation of frames containing compressed messages of 4 bytes or more is reduced by up to 99.57% compared to the Triple ID method.
- 30 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 71 (10) , 10350-10360
Dynamic Rearrangement Compression Algorithm for Intelligent Connected Vehicles
The intelligent vehicle terminal T-BOX of intelligent connected vehicles (ICVs) is directly connected to the vehicle interface and constantly exchanges real-time data inside and outside the vehicle, which significantly increases the communication pressure on the in-vehicle network. Excessive data will increase the load on the channel due to the limited bandwidth of the vehicle. Although the existing data compression algorithm can effectively reduce the communication pressure, it requires significant driving data to count the number of signal changes, which increases the preliminary labor cost. Meanwhile, it is difficult to meet the stable compression rate using a static configuration when a large amount of CAN data is transmitted with fluctuating data changes, which cannot satisfy the requirement of reducing the bus load rate, and satisfying the real-time requirements of ICV is challenging. Thus, we propose a real-time dynamic data compression algorithm for vehicles to satisfy such requirements. The experiments show that for the frequently changing signals, the proposed algorithm can improve the compression rate by about 10% compared with the existing compression algorithm. The execution time of the compression process is 4.55 μs at a clock frequency of 400 MHz and the decompression process execution time is 86.48 μs. Compared with the bus load when the original message is transmitted, the proposed algorithm can reduce the bus load by 19% on average. In the future, a stable compression rate will be crucial when loading authentication codes on the CAN to ensure its security.
- 30 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 71 (10) , 10350-10360
Dynamic Rearrangement Compression Algorithm for Intelligent Connected Vehicles
The intelligent vehicle terminal T-BOX of intelligent connected vehicles (ICVs) is directly connected to the vehicle interface and constantly exchanges real-time data inside and outside the vehicle, which significantly increases the communication pressure on the in-vehicle network. Excessive data will increase the load on the channel due to the limited bandwidth of the vehicle. Although the existing data compression algorithm can effectively reduce the communication pressure, it requires significant driving data to count the number of signal changes, which increases the preliminary labor cost. Meanwhile, it is difficult to meet the stable compression rate using a static configuration when a large amount of CAN data is transmitted with fluctuating data changes, which cannot satisfy the requirement of reducing the bus load rate, and satisfying the real-time requirements of ICV is challenging. Thus, we propose a real-time dynamic data compression algorithm for vehicles to satisfy such requirements. The experiments show that for the frequently changing signals, the proposed algorithm can improve the compression rate by about 10% compared with the existing compression algorithm. The execution time of the compression process is 4.55 μs at a clock frequency of 400 MHz and the decompression process execution time is 86.48 μs. Compared with the bus load when the original message is transmitted, the proposed algorithm can reduce the bus load by 19% on average. In the future, a stable compression rate will be crucial when loading authentication codes on the CAN to ensure its security.
- Open Access
- 3 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 126388-126399
Triple ID Flexible MAC for Can Security Improvement
The development of automotive-information & communication technology (ICT) convergence has resulted in various vehicle-based electrical/electronic (E/E) systems. An automotive E/E system consists of one or more electronic control units (ECUs), sensors and actuators. As ECUs are growing in popularity, it is necessary to have an efficient communication protocol for in-vehicle networks. Hence, a controller area network (CAN) protocol was developed by Bosch. CAN systems have been successfully applied in many areas, including the automotive industry, due to their high immunity to electrical interference and low cost. However, since the CAN protocol was designed without regard to information security functions, it has many vulnerabilities. With the commercialization of connected/autonomous cars, vehicle-based wireless communication systems have appeared, and are expected to grow in popularity. This increases the number of attack surfaces that can potentially threaten in-vehicle CAN. To combat the vulnerabilities of the CAN protocol, the CAN data field should be encrypted and transmitted with authentication codes. Recently, a method of transmitting authentication codes by modifying the CAN protocol was proposed. However, changing the original CAN protocol can cause serious problems in CAN systems. In this paper, to enhance CAN security, a data compression algorithm is used to reduce the data frame length so that there is space for a message authentication code (MAC) to be contained inside the data field. The proposed algorithm guarantees that all CAN frames are authenticated by a MAC of at least four bytes without any change of the original CAN protocol. Simulations using CAN data from Kia Sorento, Kia Soul, and LS Mtron vehicles show that the proposed algorithm works successfully with only a slight increase in the peak load.
- 3 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 126388-126399
Open AccessTriple ID Flexible MAC for Can Security Improvement
The development of automotive-information & communication technology (ICT) convergence has resulted in various vehicle-based electrical/electronic (E/E) systems. An automotive E/E system consists of one or more electronic control units (ECUs), sensors and actuators. As ECUs are growing in popularity, it is necessary to have an efficient communication protocol for in-vehicle networks. Hence, a controller area network (CAN) protocol was developed by Bosch. CAN systems have been successfully applied in many areas, including the automotive industry, due to their high immunity to electrical interference and low cost. However, since the CAN protocol was designed without regard to information security functions, it has many vulnerabilities. With the commercialization of connected/autonomous cars, vehicle-based wireless communication systems have appeared, and are expected to grow in popularity. This increases the number of attack surfaces that can potentially threaten in-vehicle CAN. To combat the vulnerabilities of the CAN protocol, the CAN data field should be encrypted and transmitted with authentication codes. Recently, a method of transmitting authentication codes by modifying the CAN protocol was proposed. However, changing the original CAN protocol can cause serious problems in CAN systems. In this paper, to enhance CAN security, a data compression algorithm is used to reduce the data frame length so that there is space for a message authentication code (MAC) to be contained inside the data field. The proposed algorithm guarantees that all CAN frames are authenticated by a MAC of at least four bytes without any change of the original CAN protocol. Simulations using CAN data from Kia Sorento, Kia Soul, and LS Mtron vehicles show that the proposed algorithm works successfully with only a slight increase in the peak load.
- Open Access
- 1 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Welcome Message - General Co-Chairs
Presents the introductory welcome message from the conference proceedings. May include the conference officers' congratulations to all involved with the conference event and publication of the proceedings record.
- 1 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Open AccessWelcome Message - General Co-Chairs
Presents the introductory welcome message from the conference proceedings. May include the conference officers' congratulations to all involved with the conference event and publication of the proceedings record.
- 12 November 2020
- Published by Springer Nature in International Journal of Automotive Technology
- Vol. 21 (6) , 1527-1537
Multi-Level Data Arrangement Algorithm for Can Data Compression
- 12 November 2020
- Published by Springer Nature in International Journal of Automotive Technology
- Vol. 21 (6) , 1527-1537
Multi-Level Data Arrangement Algorithm for Can Data Compression
- 31 July 2015
- Published by Springer Nature in Wireless Personal Communications
- Vol. 85 (4) , 2003-2019
Signal Constellations of Quasi-Orthogonal Space–Time Codes for MIMO Systems
- 31 July 2015
- Published by Springer Nature in Wireless Personal Communications
- Vol. 85 (4) , 2003-2019
Signal Constellations of Quasi-Orthogonal Space–Time Codes for MIMO Systems
- 19 April 2015
- Published by Springer Nature in Wireless Personal Communications
- Vol. 83 (4) , 2899-2923
ISI Free Channel Equalization for Future 5G Mobile Terminal Using Bio-inspired Neural Networks
- 19 April 2015
- Published by Springer Nature in Wireless Personal Communications
- Vol. 83 (4) , 2899-2923
ISI Free Channel Equalization for Future 5G Mobile Terminal Using Bio-inspired Neural Networks
- 30 December 2014
- Published by Zhejiang University Press in Frontiers of Information Technology & Electronic Engineering
- Vol. 16 (1) , 70-78
Efficient controller area network data compression for automobile applications
Controller area networks (CANs) have been designed for multiplexing communication between electronic control units (ECUs) in vehicles and many high-level i
- 30 December 2014
- Published by Zhejiang University Press in Frontiers of Information Technology & Electronic Engineering
- Vol. 16 (1) , 70-78
Efficient controller area network data compression for automobile applications
Controller area networks (CANs) have been designed for multiplexing communication between electronic control units (ECUs) in vehicles and many high-level i