Sitaram Dash
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Sitaram Dash has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Chinmaya Prasad Mohanty
School of Mechanical Engineering, Vellore Institute of Technology, Vellore, India
1 shared publication - Chun-Ping Jen
Department of Mechanical Engineering and Advanced Institute of Manufacturing for High-Tech Innovations, National Chung Cheng University, Chiayi 62102, Taiwan
1 shared publication D. P. Yadav
Ultra High Vacuum Technology Section, Proton Accelerator Group, Raja Ramanna Centre for Advanced Technology, Indore, India
1 shared publicationK. V. A. N. P. S. Kumar
Ultra High Vacuum Technology Section, Proton Accelerator Group, Raja Ramanna Centre for Advanced Technology, Indore, India
1 shared publication- Karthick Muthaiah Palaniappan Gopal
School of Mechanical Engineering, Vellore Institute of Technology, Vellore 632014, India
1 shared publication - Om Adikrao More
School of Mechanical Engineering, VIT Vellore Campus, Vellore – 632014, Tamil Nadu, India
1 shared publication
Latest Publications
- 24 May 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (22) , 9979-10015
Recent Developments and Applications of TiN-Based Films Synthesized by Magnetron Sputtering
- 24 May 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (22) , 9979-10015
Recent Developments and Applications of TiN-Based Films Synthesized by Magnetron Sputtering
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2946 (1)
Design and development of an I-shaped UAV
Design, development and fabrication of an unmanned aerial vehicle (UAV) otherwise known in practice as drone is described. The special configuration involves an I-shaped design with propellers fixed onto either side of the chassis. This design accounts for thermal stability encountered by UAVs during flight. The scheme involving this UAV model provides an effective solution for higher thrust generation than the conventional options currently available. As a part of the process covering detail design, a software-based analysis to act as validation for the model was carried out. A significant finding of the model refers to vastly enhanced hover stability across line-of-sight heights. One of the specific outcomes of the model pertains to its capability for solving problems related to narrow range of manoeuvrability. This is achieved owing to its narrow framework-based architecture. It is also being reported that installation of fins on the electronic speed controller (ESC) leads to temperature reduction of approximately 50oC. Deflection of 3 mm was observed on the propellers while applying equal loads to all the propellers. The key design aspects are the I-shaped contour, material selection for the main frame and incorporation of overlapping propellers. The benefits accruing from such a design are space efficiency and superior turning speed.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2946 (1)
Open AccessDesign and development of an I-shaped UAV
Design, development and fabrication of an unmanned aerial vehicle (UAV) otherwise known in practice as drone is described. The special configuration involves an I-shaped design with propellers fixed onto either side of the chassis. This design accounts for thermal stability encountered by UAVs during flight. The scheme involving this UAV model provides an effective solution for higher thrust generation than the conventional options currently available. As a part of the process covering detail design, a software-based analysis to act as validation for the model was carried out. A significant finding of the model refers to vastly enhanced hover stability across line-of-sight heights. One of the specific outcomes of the model pertains to its capability for solving problems related to narrow range of manoeuvrability. This is achieved owing to its narrow framework-based architecture. It is also being reported that installation of fins on the electronic speed controller (ESC) leads to temperature reduction of approximately 50oC. Deflection of 3 mm was observed on the propellers while applying equal loads to all the propellers. The key design aspects are the I-shaped contour, material selection for the main frame and incorporation of overlapping propellers. The benefits accruing from such a design are space efficiency and superior turning speed.
- Open Access
- 25 January 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (3) , 384
Reviewing Performance Measures of the Die-Sinking Electrical Discharge Machining Process: Challenges and Future Scopes
The most well-known and widely used non-traditional manufacturing method is electrical discharge machining (EDM). It is well-known for its ability to cut rigid materials and high-temperature alloys that are difficult to machine with traditional methods. The significant challenges encountered in EDM are high tool wear rate, low material removal rate, and high surface roughness caused by the continuous electric spark generated between the tool and the workpiece. Researchers have reported using a variety of approaches to overcome this challenge, such as combining the die-sinking EDM process with cryogenic treatment, cryogenic cooling, powder-mixed processing, ultrasonic assistance, and other methods. This paper examines the results of these association techniques on various performance measures, such as material removal rate (MRR), tool wear rate (TWR), surface roughness, surface integrity, and recast layer formed during machining, and identifies potential gap areas and proposes a solution. The manuscript is useful for improving performance and introducing new resolutions to the field of EDM machining.
- 25 January 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (3) , 384
Open AccessReviewing Performance Measures of the Die-Sinking Electrical Discharge Machining Process: Challenges and Future Scopes
The most well-known and widely used non-traditional manufacturing method is electrical discharge machining (EDM). It is well-known for its ability to cut rigid materials and high-temperature alloys that are difficult to machine with traditional methods. The significant challenges encountered in EDM are high tool wear rate, low material removal rate, and high surface roughness caused by the continuous electric spark generated between the tool and the workpiece. Researchers have reported using a variety of approaches to overcome this challenge, such as combining the die-sinking EDM process with cryogenic treatment, cryogenic cooling, powder-mixed processing, ultrasonic assistance, and other methods. This paper examines the results of these association techniques on various performance measures, such as material removal rate (MRR), tool wear rate (TWR), surface roughness, surface integrity, and recast layer formed during machining, and identifies potential gap areas and proposes a solution. The manuscript is useful for improving performance and introducing new resolutions to the field of EDM machining.