Luke Geise
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Luke Geise has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Andrew Abbott
Air Force Research Laboratory, Wright Patterson Air Force Base, OH, USA
2 shared publications Daniel Rapking
Department of Structural Materials Division, University of Dayton Research Institute, Dayton, OH, USA
2 shared publicationsRyan Seifert
Department of Structural Materials Division, University of Dayton Research Institute, Dayton, OH, USA
2 shared publicationsAndrew Abbott
Univ Dayton, Res Inst, Struct Mat Div, Dayton, OH 45469 USA
1 shared publication- Daniel Rapking1 shared publication
Mark Flores
Air Force Research Laboratory, WPAFB, OH, USA
1 shared publication
Latest Publications
- 25 March 2022
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 56 (11) , 1677-1691
Experimental investigation of the modified butterfly notch shear specimen with PMCs
An experimental study of the modified butterfly shear sample was undertaken for polymer matrix composites using three quasi-isotropic IM7/977-3 laminates. This study used 3D digital image correlation (DIC) to observe and quantify the severe shear strain concentrations developed by compressively loading the modified butterfly geometry laminates. Interrupted X-Ray computed tomography (X-Ray CT) was used to understand the failure mechanisms present in the region of shear strain. By choosing to conduct interrupted testing, the progressive nature of the damage could be observed. At ultimate failure, extensive damage in the region of high shear strain was observed using post testing inspection with X-Ray CT. The mechanical testing was accompanied by numerical simulations for each laminate. The damage predicted by the numerical simulations was shown to be consistent with the damage observed with the post failure inspection via X-Ray CT. Stress components caused by free-edge effects were also quantified, and shown to have a minimal impact on the failure mode in the region of interest.
- 25 March 2022
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 56 (11) , 1677-1691
Experimental investigation of the modified butterfly notch shear specimen with PMCs
An experimental study of the modified butterfly shear sample was undertaken for polymer matrix composites using three quasi-isotropic IM7/977-3 laminates. This study used 3D digital image correlation (DIC) to observe and quantify the severe shear strain concentrations developed by compressively loading the modified butterfly geometry laminates. Interrupted X-Ray computed tomography (X-Ray CT) was used to understand the failure mechanisms present in the region of shear strain. By choosing to conduct interrupted testing, the progressive nature of the damage could be observed. At ultimate failure, extensive damage in the region of high shear strain was observed using post testing inspection with X-Ray CT. The mechanical testing was accompanied by numerical simulations for each laminate. The damage predicted by the numerical simulations was shown to be consistent with the damage observed with the post failure inspection via X-Ray CT. Stress components caused by free-edge effects were also quantified, and shown to have a minimal impact on the failure mode in the region of interest.
- 1 December 2021
- Published by Elsevier in Computational Materials Science
- Vol. 200
Harnessing shape optimization techniques to develop novel methods to determine shear properties in PMCs
- 1 December 2021
- Published by Elsevier in Computational Materials Science
- Vol. 200
Harnessing shape optimization techniques to develop novel methods to determine shear properties in PMCs
- 20 September 2021
- Published by DEStech Publications
PERFORMANCE OF ADDITIVELY MANUFACTURED CHOPPED FIBER COMPOSITES AS A FUNCTION OF POROSITY
Additive manufacturing (AM) of short-fiber reinforced composites are actively being considered for construction of low-cost, weight reducing alternatives to non-structural metal components. In addition AM parts are being used for rapid manufacturing of composite tooling. AM is notorious for generating parts with higher porosity than more traditional manufacturing technologies. Due to the aerospace industry’s low risk tolerance, novel material systems require comprehensive characterization of their associated manufacturing defects and the impact of defects on performance in order to receive certification. AM short fiber composites still require this analysis. Although traditional composite manufacturing methods, such as an autoclave or VARTM can produce porosity, the origin and transport of porosity has been thoroughly studied and acceptable limits for part qualification have been established to minimize the effect on performance. In AM components studies establishing the origination of porosity origin and processing defect related minimization strategies are lacking. A preliminary study on the impacts of porosity caused by print parameters such print speed, layer height, first layer height, and step-over distance has been undertaken. Direct Ink Writing (DIW) was selected for this study using an epoxy-based ink filled with clay and chopped carbon fiber. To understand performance, fracture and shear specimens were fabricated with different test parameters based on the assumed levels of porosity from screening tests. Samples were then mechanically tested using a novel in-plane shear test method and a single edge notch tension test. This study explores the processing parameter’s contribution to porosity and establishes general trends to understand the influence of porosity on performance for additively manufactured chopped fiber composites.
- 20 September 2021
- Published by DEStech Publications
PERFORMANCE OF ADDITIVELY MANUFACTURED CHOPPED FIBER COMPOSITES AS A FUNCTION OF POROSITY
Additive manufacturing (AM) of short-fiber reinforced composites are actively being considered for construction of low-cost, weight reducing alternatives to non-structural metal components. In addition AM parts are being used for rapid manufacturing of composite tooling. AM is notorious for generating parts with higher porosity than more traditional manufacturing technologies. Due to the aerospace industry’s low risk tolerance, novel material systems require comprehensive characterization of their associated manufacturing defects and the impact of defects on performance in order to receive certification. AM short fiber composites still require this analysis. Although traditional composite manufacturing methods, such as an autoclave or VARTM can produce porosity, the origin and transport of porosity has been thoroughly studied and acceptable limits for part qualification have been established to minimize the effect on performance. In AM components studies establishing the origination of porosity origin and processing defect related minimization strategies are lacking. A preliminary study on the impacts of porosity caused by print parameters such print speed, layer height, first layer height, and step-over distance has been undertaken. Direct Ink Writing (DIW) was selected for this study using an epoxy-based ink filled with clay and chopped carbon fiber. To understand performance, fracture and shear specimens were fabricated with different test parameters based on the assumed levels of porosity from screening tests. Samples were then mechanically tested using a novel in-plane shear test method and a single edge notch tension test. This study explores the processing parameter’s contribution to porosity and establishes general trends to understand the influence of porosity on performance for additively manufactured chopped fiber composites.