Richard Avella
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Richard Avella has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Camila Andrea Gonzalez
Faculty of Engineering and Basic Sciences, Fundación Universitaria Los Libertadores, Bogotá A.A. 75087, Colombia
2 shared publications D Grajales
Faculty of Engineering
2 shared publications- D. Grajales2 shared publications
- Francisco Javier Gonzalez Cruz
Fundación Universitaria los Libertadores
2 shared publications J P Rubio
Department of Aeronautical Engineering
2 shared publicationsJp Rubio
2 shared publications
Latest Publications
- Open Access
- 3 October 2026
- Published by Elsevier in SSRN Electronic Journal
Droplet Impact Characterization on Rotating Propeller Blades2Under Simulated Icing Conditions Using Water-Sensitive Paper
Droplet impingement on rotating blades is a critical mechanism in the onset of in-flight icing, yet the combined effects of wind speed and blade pitch angle on impact characteristics remain insufficiently quantified under controlled conditions. This study characterizes water droplet impact on a two-blade propeller assembly rotating at a fixed speed of 3760~rpm using water-sensitive paper (WSP) as the detection medium. Three wind speeds (6~m~s$^{-1}$, 8~m~s$^{-1}$ and 10~m~s$^{-1}$) and four pitch angles (6$^{\circ}$, 12$^{\circ}$, 18$^{\circ}$ and 24$^{\circ}$) were tested in a factorial design with three independent replicates per condition, yielding 67 valid observations. Droplet density and the median volume diameter (MVD) were extracted from high-resolution WSP scans through automated image analysis. Statistical analysis showed that pitch angle was the dominant factor controlling impact density ($H=34.37$, $p<0.001$, $\varepsilon^2\approx0.50$), whereas wind speed produced a smaller but statistically significant effect ($H=8.63$, $p=0.013$, $\varepsilon^2\approx0.10$). The response exhibited a positive interaction between wind speed and pitch angle, with the sensitivity to freestream velocity increasing at higher pitch angles. The highest measured impact density was $489.9\pm88.2$ drops/cm$^2$ at $10$ m/s and $24^\circ$. An exploratory power-law analysis of the twelve condition means yielded $\rho_d\approx0.0204V_{\infty}^{2.14}\beta^{1.63}$ with $R^2\approx0.966$. MVD showed substantially weaker dependence on the experimental factors and remained within approximately $139$--$153~\mu$m when grouped by wind speed. The results demonstrate that pitch angle primarily controls droplet loading, while wind speed amplifies this loading at high pitch angles.- 3 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDroplet Impact Characterization on Rotating Propeller Blades2Under Simulated Icing Conditions Using Water-Sensitive Paper
Droplet impingement on rotating blades is a critical mechanism in the onset of in-flight icing, yet the combined effects of wind speed and blade pitch angle on impact characteristics remain insufficiently quantified under controlled conditions. This study characterizes water droplet impact on a two-blade propeller assembly rotating at a fixed speed of 3760~rpm using water-sensitive paper (WSP) as the detection medium. Three wind speeds (6~m~s$^{-1}$, 8~m~s$^{-1}$ and 10~m~s$^{-1}$) and four pitch angles (6$^{\circ}$, 12$^{\circ}$, 18$^{\circ}$ and 24$^{\circ}$) were tested in a factorial design with three independent replicates per condition, yielding 67 valid observations. Droplet density and the median volume diameter (MVD) were extracted from high-resolution WSP scans through automated image analysis. Statistical analysis showed that pitch angle was the dominant factor controlling impact density ($H=34.37$, $p<0.001$, $\varepsilon^2\approx0.50$), whereas wind speed produced a smaller but statistically significant effect ($H=8.63$, $p=0.013$, $\varepsilon^2\approx0.10$). The response exhibited a positive interaction between wind speed and pitch angle, with the sensitivity to freestream velocity increasing at higher pitch angles. The highest measured impact density was $489.9\pm88.2$ drops/cm$^2$ at $10$ m/s and $24^\circ$. An exploratory power-law analysis of the twelve condition means yielded $\rho_d\approx0.0204V_{\infty}^{2.14}\beta^{1.63}$ with $R^2\approx0.966$. MVD showed substantially weaker dependence on the experimental factors and remained within approximately $139$--$153~\mu$m when grouped by wind speed. The results demonstrate that pitch angle primarily controls droplet loading, while wind speed amplifies this loading at high pitch angles. - Open Access
AtmosphericIcing Mitigation on Unmanned Aerial Vehicles: Electrothermal Strategies and Functional Materials for Operational Safety Under Known Icing Conditions
Atmospheric icing is one of the most critical meteorological hazards for unmanned aerial vehicles (UAV), whose operation under adverse conditions—high latitudes, elevated altitudes, long-endurance missions without pilot intervention—particularly exposes them to ice accumulation on aerodynamic surfaces and propellers. Unlike manned aviation, where this phenomenon has been extensively studied and regulated, a significant knowledge gap exists in the UAV domain that limits the development of effective protection systems adapted to energy constraints. This article provides an integrative review—conducted with a systematic search strategy following PRISMA reporting guidelines—of atmospheric ice formation mechanisms, their specific effects on UAV propellers, and the two most promising mitigation approaches: electrothermal modelling for the optimisation of electric heating systems and the development of functional surface materials including superhydrophobic coatings (SHC); composites with conductive nanofillers (graphene, carbon nanotubes); and piezoelectric actuators. The analysis demonstrates that hybrid systems combining passive and active strategies managed by intelligent control represent the most viable solution for extending UAV operational envelopes under known icing conditions, with a projected reduction in anti-icing system energy consumption of at least 40% relative to conventional continuous heating. This estimate is based on the most conservative published evidence: pulsed electrothermal de-icing achieves 40–60% savings versus continuous anti-icingSHC-assisted hybrid heating reduces IPS power by more than 80% on static aerofoils; and rotary-wing pulsed systems reduce mean consumption by 60–75% relative to continuous operation. Key research gaps are identified, and a prioritised future research agenda is proposed to support the development of certifiable anti-icing systems for rotary-wing UAV platforms.
Open AccessAtmosphericIcing Mitigation on Unmanned Aerial Vehicles: Electrothermal Strategies and Functional Materials for Operational Safety Under Known Icing Conditions
Atmospheric icing is one of the most critical meteorological hazards for unmanned aerial vehicles (UAV), whose operation under adverse conditions—high latitudes, elevated altitudes, long-endurance missions without pilot intervention—particularly exposes them to ice accumulation on aerodynamic surfaces and propellers. Unlike manned aviation, where this phenomenon has been extensively studied and regulated, a significant knowledge gap exists in the UAV domain that limits the development of effective protection systems adapted to energy constraints. This article provides an integrative review—conducted with a systematic search strategy following PRISMA reporting guidelines—of atmospheric ice formation mechanisms, their specific effects on UAV propellers, and the two most promising mitigation approaches: electrothermal modelling for the optimisation of electric heating systems and the development of functional surface materials including superhydrophobic coatings (SHC); composites with conductive nanofillers (graphene, carbon nanotubes); and piezoelectric actuators. The analysis demonstrates that hybrid systems combining passive and active strategies managed by intelligent control represent the most viable solution for extending UAV operational envelopes under known icing conditions, with a projected reduction in anti-icing system energy consumption of at least 40% relative to conventional continuous heating. This estimate is based on the most conservative published evidence: pulsed electrothermal de-icing achieves 40–60% savings versus continuous anti-icingSHC-assisted hybrid heating reduces IPS power by more than 80% on static aerofoils; and rotary-wing pulsed systems reduce mean consumption by 60–75% relative to continuous operation. Key research gaps are identified, and a prioritised future research agenda is proposed to support the development of certifiable anti-icing systems for rotary-wing UAV platforms.
- Open Access
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Numerical Assessment of Supercooled Droplet Impingement andCollection Efficiency on a NACA~4415 Airfoil:A Lagrangian--Eulerian Framework in OpenFOAM
This study presents a numerical investigation of supercooled droplet impingement and collection efficiency on a cambered NACA~4415 airfoil ($t/c=0.15$, $m/c=0.04$ at $p/c=0.40$) at $Re = 3.29\times10^{6}$ and $\alpha=0^{\circ}$ using OpenFOAM~2506. The steady incompressible RANS flow field, closed with the $k$--$\omega$~SST turbulence model, drives an offline Lagrangian trajectory solver with Schiller--Naumann drag correction. Collection efficiency $E$ is computed parametrically for $\mathrm{MVD}\in\{20,50,100,200\}~\upmu$m ($St\in[0.053,5.316]$), covering the full range from FAA Appendix~C stratiform clouds to Appendix~O supercooled large droplets (SLD). Grid independence is confirmed for $\mathrm{MVD}\geq50~\upmu$m across three systematically refined meshes ($1.08\times10^{5}$--$6.01\times10^{6}$ cells), with medium-to-fine relative changes below $3.6\%$. $E$ increases monotonically from $0.036$ ($St=0.053$) to $0.306$ ($St=5.316$), exhibiting the three canonical dynamical regimes: low-inertia aerodynamic deflection, a log-linear transition ($E\approx0.056\ln St+0.196$, $R^{2}=0.996$), and high-inertia ballistic approach to the geometric limit. Compared with the symmetric NACA~0024 at identical conditions, the NACA~4415 yields $27$--$33\,\%$ lower $E$ for $\mathrm{MVD}\geq50~\upmu$m, attributable to its reduced leading-edge radius ($r_{\mathrm{LE}}/c\approx0.0158$ vs.~$0.0449$), lower thickness ratio ($t/c=0.15$ vs.~$0.24$), and camber-induced stagnation-point asymmetry that shifts impingement toward the suction surface. The water mass flux per unit span, $\dot{m}=\mathrm{LWC}\,U_{\infty}\,c\,E$, ranges from $0.90$~g/(m$\cdot$s) under Appendix~C stratiform conditions to $5.40$~g/(m$\cdot$s) under Appendix~O SLD---a sixfold increase that quantifies the inadequacy of Appendix-C-based ice-protection sizing for SLD exposure on moderately thick cambered profiles. These results provide the first open-source $\beta(s)$ and $E$ dataset for the NACA~4415, with supporting scripts and tabulated data publicly available.- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNumerical Assessment of Supercooled Droplet Impingement andCollection Efficiency on a NACA~4415 Airfoil:A Lagrangian--Eulerian Framework in OpenFOAM
This study presents a numerical investigation of supercooled droplet impingement and collection efficiency on a cambered NACA~4415 airfoil ($t/c=0.15$, $m/c=0.04$ at $p/c=0.40$) at $Re = 3.29\times10^{6}$ and $\alpha=0^{\circ}$ using OpenFOAM~2506. The steady incompressible RANS flow field, closed with the $k$--$\omega$~SST turbulence model, drives an offline Lagrangian trajectory solver with Schiller--Naumann drag correction. Collection efficiency $E$ is computed parametrically for $\mathrm{MVD}\in\{20,50,100,200\}~\upmu$m ($St\in[0.053,5.316]$), covering the full range from FAA Appendix~C stratiform clouds to Appendix~O supercooled large droplets (SLD). Grid independence is confirmed for $\mathrm{MVD}\geq50~\upmu$m across three systematically refined meshes ($1.08\times10^{5}$--$6.01\times10^{6}$ cells), with medium-to-fine relative changes below $3.6\%$. $E$ increases monotonically from $0.036$ ($St=0.053$) to $0.306$ ($St=5.316$), exhibiting the three canonical dynamical regimes: low-inertia aerodynamic deflection, a log-linear transition ($E\approx0.056\ln St+0.196$, $R^{2}=0.996$), and high-inertia ballistic approach to the geometric limit. Compared with the symmetric NACA~0024 at identical conditions, the NACA~4415 yields $27$--$33\,\%$ lower $E$ for $\mathrm{MVD}\geq50~\upmu$m, attributable to its reduced leading-edge radius ($r_{\mathrm{LE}}/c\approx0.0158$ vs.~$0.0449$), lower thickness ratio ($t/c=0.15$ vs.~$0.24$), and camber-induced stagnation-point asymmetry that shifts impingement toward the suction surface. The water mass flux per unit span, $\dot{m}=\mathrm{LWC}\,U_{\infty}\,c\,E$, ranges from $0.90$~g/(m$\cdot$s) under Appendix~C stratiform conditions to $5.40$~g/(m$\cdot$s) under Appendix~O SLD---a sixfold increase that quantifies the inadequacy of Appendix-C-based ice-protection sizing for SLD exposure on moderately thick cambered profiles. These results provide the first open-source $\beta(s)$ and $E$ dataset for the NACA~4415, with supporting scripts and tabulated data publicly available. - 24 July 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (30) , 306001
Comparative analysis of PINNs, DeepONets, and spectral diagonalization for quantum tunneling in a double-well potential
We present a comparative study of exact spectral diagonalization, Physics-informed neural networks (PINNs), and deep operator networks (DeepONets) applied to quantum tunneling in a one-dimensional double-well potential. The ground-state energy and tunneling splitting are computed across a range of potential parameters. While PINNs achieve near-spectral accuracy, they exhibit higher computational cost and occasional training instabilities. In contrast, DeepONets provide fast and robust surrogate predictions once trained, enabling efficient parametric exploration. The proposed workflow is fully reproducible; extensions to higher-dimensional potentials or many-body systems, where exact diagonalization becomes computationally prohibitive, are proposed as a natural avenue for future work but lie beyond the scope of the present study.
- 24 July 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (30) , 306001
Comparative analysis of PINNs, DeepONets, and spectral diagonalization for quantum tunneling in a double-well potential
We present a comparative study of exact spectral diagonalization, Physics-informed neural networks (PINNs), and deep operator networks (DeepONets) applied to quantum tunneling in a one-dimensional double-well potential. The ground-state energy and tunneling splitting are computed across a range of potential parameters. While PINNs achieve near-spectral accuracy, they exhibit higher computational cost and occasional training instabilities. In contrast, DeepONets provide fast and robust surrogate predictions once trained, enabling efficient parametric exploration. The proposed workflow is fully reproducible; extensions to higher-dimensional potentials or many-body systems, where exact diagonalization becomes computationally prohibitive, are proposed as a natural avenue for future work but lie beyond the scope of the present study.
- Open Access
- 13 May 2026
- Published by MDPI AG in Preprints.org
Atmospheric Icing Mitigation on Unmanned Aerial Vehicles: Electrothermal Strategies and Functional Materials for Operational Safety Under Known Icing Conditions
Atmospheric icing is one of the most critical meteorological hazards for unmanned aerial vehicles (UAV), whose operation under adverse conditions—high latitudes, elevated altitudes, long-endurance missions without pilot intervention—particularly exposes them to ice accumulation on aerodynamic surfaces and propellers. Unlike manned aviation, where this phenomenon has been extensively studied and regulated, a significant knowledge gap exists in the UAV domain that limits the development of effective protection systems adapted to energy constraints. This article provides an integrated review of atmospheric ice formation mechanisms, their specific effects on UAV propellers, and the two most promising mitigation approaches: electrothermal modelling for the optimisation of electric heating systems, and the development of functional surface materials, including superhydrophobic coatings (SHC), composites with conductive nanofillers (graphene, carbon nanotubes), and piezoelectric actuators. The analysis demonstrates that hybrid systems combining passive and active strategies managed by intelligent control represent the most viable solution for extending UAV operational envelopes under known icing conditions, with a potential reduction in anti-icing energy consumption exceeding 40% compared to conventional continuous heating. Key research gaps are identified, and a prioritised future research agenda is proposed to support the development of certifiable anti-icing systems for rotary-wing UAV platforms.
- 13 May 2026
- Published by MDPI AG in Preprints.org
Open AccessAtmospheric Icing Mitigation on Unmanned Aerial Vehicles: Electrothermal Strategies and Functional Materials for Operational Safety Under Known Icing Conditions
Atmospheric icing is one of the most critical meteorological hazards for unmanned aerial vehicles (UAV), whose operation under adverse conditions—high latitudes, elevated altitudes, long-endurance missions without pilot intervention—particularly exposes them to ice accumulation on aerodynamic surfaces and propellers. Unlike manned aviation, where this phenomenon has been extensively studied and regulated, a significant knowledge gap exists in the UAV domain that limits the development of effective protection systems adapted to energy constraints. This article provides an integrated review of atmospheric ice formation mechanisms, their specific effects on UAV propellers, and the two most promising mitigation approaches: electrothermal modelling for the optimisation of electric heating systems, and the development of functional surface materials, including superhydrophobic coatings (SHC), composites with conductive nanofillers (graphene, carbon nanotubes), and piezoelectric actuators. The analysis demonstrates that hybrid systems combining passive and active strategies managed by intelligent control represent the most viable solution for extending UAV operational envelopes under known icing conditions, with a potential reduction in anti-icing energy consumption exceeding 40% compared to conventional continuous heating. Key research gaps are identified, and a prioritised future research agenda is proposed to support the development of certifiable anti-icing systems for rotary-wing UAV platforms.
- Open Access
- 30 April 2026
- Published by Elsevier in SSRN Electronic Journal
"Numerical Assessment of Supercooled Droplet Collection Efficiency on a NACA 0024 Airfoil Under Icing Conditions: A Lagrangian–Eulerian Framework in OpenFOAM"
This study presents a numerical investigation of supercooled large-droplet (SLD)impingement and collection efficiency on a symmetric NACA\,0024 airfoil at achord Reynolds number of $\Rey = 3.33 \times 10^{6}$ under glaze-icing flightconditions. A quasi-two-dimensional, incompressible Eulerian flow field iscomputed using the finite-volume solver OpenFOAM\,2506, employing the$k$--$\omega$ SST turbulence closure with standard wall functions on anunstructured hexahedral-dominant mesh generated by \texttt{snappyHexMesh}. Theconverged velocity field is subsequently used as a frozen background flow foran off-line Lagrangian trajectory integration of water droplets, whose equationsof motion incorporate Schiller--Naumann drag correction and gravitational bodyforce. The local collection efficiency $\betacol(s)$ and total collectionefficiency $\Ecol$ are derived analytically from the computed droplet impingementpatterns for four median-volume diameters ($\MVD = 20,\,50,\,100$, and\SI{200}{\micro\meter}), spanning Stokes numbers $\Stk \in [0.063,\,6.34]$.Grid independence is demonstrated across three mesh densities (coarse:\num{71843} cells; medium: \num{890013} cells; fine: \num{2132001} cells),showing $\Ecol$ variations below \SI{5}{\percent} between the medium and finegrids for $\MVD \geq \SI{50}{\micro\meter}$. Results indicate strongconcentration of impingement near the leading edge ($x/c < 0.05$) for alldroplet sizes, with $\Ecol$ increasing monotonically from \num{0.035} at$\MVD = \SI{20}{\micro\meter}$ to \num{0.450} at$\MVD = \SI{200}{\micro\meter}$, in good qualitative agreement withLEWICE\,3.2 benchmarks for symmetric profiles. The proposed workflow providesan open-source, computationally tractable methodology for icing certificationstudies.- 30 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open Access"Numerical Assessment of Supercooled Droplet Collection Efficiency on a NACA 0024 Airfoil Under Icing Conditions: A Lagrangian–Eulerian Framework in OpenFOAM"
This study presents a numerical investigation of supercooled large-droplet (SLD)impingement and collection efficiency on a symmetric NACA\,0024 airfoil at achord Reynolds number of $\Rey = 3.33 \times 10^{6}$ under glaze-icing flightconditions. A quasi-two-dimensional, incompressible Eulerian flow field iscomputed using the finite-volume solver OpenFOAM\,2506, employing the$k$--$\omega$ SST turbulence closure with standard wall functions on anunstructured hexahedral-dominant mesh generated by \texttt{snappyHexMesh}. Theconverged velocity field is subsequently used as a frozen background flow foran off-line Lagrangian trajectory integration of water droplets, whose equationsof motion incorporate Schiller--Naumann drag correction and gravitational bodyforce. The local collection efficiency $\betacol(s)$ and total collectionefficiency $\Ecol$ are derived analytically from the computed droplet impingementpatterns for four median-volume diameters ($\MVD = 20,\,50,\,100$, and\SI{200}{\micro\meter}), spanning Stokes numbers $\Stk \in [0.063,\,6.34]$.Grid independence is demonstrated across three mesh densities (coarse:\num{71843} cells; medium: \num{890013} cells; fine: \num{2132001} cells),showing $\Ecol$ variations below \SI{5}{\percent} between the medium and finegrids for $\MVD \geq \SI{50}{\micro\meter}$. Results indicate strongconcentration of impingement near the leading edge ($x/c < 0.05$) for alldroplet sizes, with $\Ecol$ increasing monotonically from \num{0.035} at$\MVD = \SI{20}{\micro\meter}$ to \num{0.450} at$\MVD = \SI{200}{\micro\meter}$, in good qualitative agreement withLEWICE\,3.2 benchmarks for symmetric profiles. The proposed workflow providesan open-source, computationally tractable methodology for icing certificationstudies. - Open Access
- 10 March 2026
- Published by Elsevier in SSRN Electronic Journal
Aerodynamic and Thermodynamic Modeling of Ice Formation on the NACA 4415 Airfoil
Ice accretion on aircraft surfaces poses a major hazard to flight safety and performance, particularly under subsonic operating conditions. This study investigates the aerodynamic and thermodynamic mechanisms driving ice formation on the NACA 4415 airfoil through a coupled framework combining potential-flow aerodynamics, Messinger’s energy balance, and microphysical droplet modeling. The model predicts the spatial distribution of ice thickness across a range of altitudes, velocities, and angles of attack, revealing that accretion is governed by the joint influence of dynamic pressure, convective heat-transfer rates, and droplet collection efficiency. Results show that ice formation is most likely within a narrow operational envelope around α = 8◦ –10◦ , where aerodynamic cooling and droplet impingement converge to reduce surface temperature below freezing. Although the simplified framework captures the dominant spatial trends observed in wind-tunnel data and LEWICE 2/2.2 simulations, quantitative discrepancies persist, with RMSE values near 0.048–0.049 m and elevated normalized errors reflecting the inherent sensitivity of the accretion process. Despite these limitations, the methodology provides a computationally efficient tool for identifying critical icing regions and supporting preliminary risk assessments. The findings offer design insights for leading-edge optimization, thermal management, and onboard sensing, contributing to improved anti-icing strategies and safer aircraft operation in adverse meteorological environments.
- 10 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAerodynamic and Thermodynamic Modeling of Ice Formation on the NACA 4415 Airfoil
Ice accretion on aircraft surfaces poses a major hazard to flight safety and performance, particularly under subsonic operating conditions. This study investigates the aerodynamic and thermodynamic mechanisms driving ice formation on the NACA 4415 airfoil through a coupled framework combining potential-flow aerodynamics, Messinger’s energy balance, and microphysical droplet modeling. The model predicts the spatial distribution of ice thickness across a range of altitudes, velocities, and angles of attack, revealing that accretion is governed by the joint influence of dynamic pressure, convective heat-transfer rates, and droplet collection efficiency. Results show that ice formation is most likely within a narrow operational envelope around α = 8◦ –10◦ , where aerodynamic cooling and droplet impingement converge to reduce surface temperature below freezing. Although the simplified framework captures the dominant spatial trends observed in wind-tunnel data and LEWICE 2/2.2 simulations, quantitative discrepancies persist, with RMSE values near 0.048–0.049 m and elevated normalized errors reflecting the inherent sensitivity of the accretion process. Despite these limitations, the methodology provides a computationally efficient tool for identifying critical icing regions and supporting preliminary risk assessments. The findings offer design insights for leading-edge optimization, thermal management, and onboard sensing, contributing to improved anti-icing strategies and safer aircraft operation in adverse meteorological environments.
- Open Access
- 6 February 2026
- Published by Elsevier in SSRN Electronic Journal
Aerodynamic and Thermodynamic Modeling of Ice Formation on the NACA 4415 Airfoil
Ice accretion on aircraft surfaces poses a major hazard to flight safety and performance, particularly undersubsonic operating conditions. This study investigates the aerodynamic and thermodynamic mechanisms drivingice formation on the NACA 4415 airfoil through a coupled framework combining potential-flow aerodynamics,Messinger’s energy balance, and microphysical droplet modeling. The model predicts the spatial distributionof ice thickness across a range of altitudes, velocities, and angles of attack, revealing that accretion is governedby the joint influence of dynamic pressure, convective heat-transfer rates, and droplet collection efficiency.Results show that ice formation is most likely within a narrow operational envelope around α = 8◦ –10◦ , whereaerodynamic cooling and droplet impingement converge to reduce surface temperature below freezing. Althoughthe simplified framework captures the dominant spatial trends observed in wind-tunnel data and LEWICE 2/2.2simulations, quantitative discrepancies persist, with RMSE values near 0.048–0.049 m and elevated normalizederrors reflecting the inherent sensitivity of the accretion process. Despite these limitations, the methodologyprovides a computationally efficient tool for identifying critical icing regions and supporting preliminary riskassessments. The findings offer design insights for leading-edge optimization, thermal management, and onboardsensing, contributing to improved anti-icing strategies and safer aircraft operation in adverse meteorologicalenvironments.
- 6 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAerodynamic and Thermodynamic Modeling of Ice Formation on the NACA 4415 Airfoil
Ice accretion on aircraft surfaces poses a major hazard to flight safety and performance, particularly undersubsonic operating conditions. This study investigates the aerodynamic and thermodynamic mechanisms drivingice formation on the NACA 4415 airfoil through a coupled framework combining potential-flow aerodynamics,Messinger’s energy balance, and microphysical droplet modeling. The model predicts the spatial distributionof ice thickness across a range of altitudes, velocities, and angles of attack, revealing that accretion is governedby the joint influence of dynamic pressure, convective heat-transfer rates, and droplet collection efficiency.Results show that ice formation is most likely within a narrow operational envelope around α = 8◦ –10◦ , whereaerodynamic cooling and droplet impingement converge to reduce surface temperature below freezing. Althoughthe simplified framework captures the dominant spatial trends observed in wind-tunnel data and LEWICE 2/2.2simulations, quantitative discrepancies persist, with RMSE values near 0.048–0.049 m and elevated normalizederrors reflecting the inherent sensitivity of the accretion process. Despite these limitations, the methodologyprovides a computationally efficient tool for identifying critical icing regions and supporting preliminary riskassessments. The findings offer design insights for leading-edge optimization, thermal management, and onboardsensing, contributing to improved anti-icing strategies and safer aircraft operation in adverse meteorologicalenvironments.
- 14 May 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (6) , 065954
Quantum fidelity and Von Neumann entropy of a Bose-Fermi mixture in 1D double well potential
The time evolution of probability density, the ground-state fidelity and the entanglement of a Bose-Fermi mixture in a 1D double well potential, are studied through the two-mode approximation. We found that the behavior of the quantum return probability shows three distinct regions. The first region is characterized by a complete miscibility, and correlated tunneling of bosons and fermion. The second region is characterized by correlated sequential tunneling and in the last region we found an increase in the tunneling frequency of the two species. Through the Von Neumann entropy, we found that the boson-fermion coupling allows a maximum entanglement of quantum correlations of bosons and fermions in the same value. Finally, Considering variations in the interaction between pairs of fermions λ FF , pairs of bosons λ BB , and variations in the interaction between particles of different species λ BF , we calculated the fidelity in the λ FF − λ BF and λ BB − λ BF planes and we found that the drop of the two fidelities becomes deeper and deeper as the boson-fermion interaction decreases.
- 14 May 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (6) , 065954
Quantum fidelity and Von Neumann entropy of a Bose-Fermi mixture in 1D double well potential
The time evolution of probability density, the ground-state fidelity and the entanglement of a Bose-Fermi mixture in a 1D double well potential, are studied through the two-mode approximation. We found that the behavior of the quantum return probability shows three distinct regions. The first region is characterized by a complete miscibility, and correlated tunneling of bosons and fermion. The second region is characterized by correlated sequential tunneling and in the last region we found an increase in the tunneling frequency of the two species. Through the Von Neumann entropy, we found that the boson-fermion coupling allows a maximum entanglement of quantum correlations of bosons and fermions in the same value. Finally, Considering variations in the interaction between pairs of fermions λ FF , pairs of bosons λ BB , and variations in the interaction between particles of different species λ BF , we calculated the fidelity in the λ FF − λ BF and λ BB − λ BF planes and we found that the drop of the two fidelities becomes deeper and deeper as the boson-fermion interaction decreases.
- Open Access
- 20 December 2023
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (1) , 015007
Unconventional fly-gen airborne wind energy system
Based on capturing wind energy at altitudes, known as Airborne Wind Energy Systems (AWES , and the system called Ram air turbine (RAT), we propose and study an Unconventional Fly-Gen Airborne Wind Energy System that converses mechanical energy into electrical energy by Faraday’s law of induction, using mass flow produced on the PT6 engine cowling operating at idle gear. We show that it is possible to obtain electromotive force by varying the angle between the air mass produced by the engine propeller and the axial fan. We found that the amplitude and frequency of this EMF are inverse functions of cos γ and the induced peak power is independent of the type of biofuel with which the PT6 is fed.
- 20 December 2023
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (1) , 015007
Open AccessUnconventional fly-gen airborne wind energy system
Based on capturing wind energy at altitudes, known as Airborne Wind Energy Systems (AWES , and the system called Ram air turbine (RAT), we propose and study an Unconventional Fly-Gen Airborne Wind Energy System that converses mechanical energy into electrical energy by Faraday’s law of induction, using mass flow produced on the PT6 engine cowling operating at idle gear. We show that it is possible to obtain electromotive force by varying the angle between the air mass produced by the engine propeller and the axial fan. We found that the amplitude and frequency of this EMF are inverse functions of cos γ and the induced peak power is independent of the type of biofuel with which the PT6 is fed.