Wasim Dipon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wasim Dipon has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Amar S. Bhalla
Department of Electrical and Computer Engineering, the University of Texas at San Antonio, 1 UTSA Circle, San Antonio, TX 78249, USA
3 shared publications - Ruyan Guo
Department of Electrical and Computer Engineering, the University of Texas at San Antonio, 1 UTSA Circle, San Antonio, TX 78249, USA
3 shared publications - Bryan Gamboa
Department of Electrical and Computer Engineering, the University of Texas at San Antonio, 1 UTSA Circle, San Antonio, TX 78249, USA
2 shared publications Amar Bhalla
Department of Electrical and Computer Engineering, The University of Texas at San Antonio, San Antonio, TX, USA
1 shared publication- Bryan Gamboa
Department of Electrical and Computer Engineering, University of Texas at San Antonio, San Antonio, TX 78249, USA
1 shared publication - Carlos A. Acosta
Department of Electrical and Computer Engineering, the University of Texas at San Antonio, 1 UTSA Circle, San Antonio, TX 78249, USA
1 shared publication
Latest Publications
- Open Access
- 16 June 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (6) , 304
Modeling and Experimental Evaluation of 1-3 Stacked Piezoelectric Transducers for Energy Harvesting
Piezoelectric energy harvesting in roadways can power distributed sensors and electronics by capturing underutilized mechanical energy from traffic. In this research, 1-3 stacked piezocomposites were developed and evaluated to determine optimal designs for multiple applications. The design of these transducers aimed at operating in a multitude of scenarios, under compressive loads (1–10 kN) at low-frequency (10 Hz) applications, intended to simulate vehicular forces. Power comparison was utilized between numerous transducers to determine the most efficient configuration for electromechanical energy conversion. Design guidelines were based on mechanical integrity, output power, active piezoelectric volume percentage, aspect ratio, and geometric factors. The forces applied in this study were reliant on the average vehicle weight. An intermediate PZT volume fraction and moderate pillar aspect ratios were found to yield the highest power output, with the stacked 1-3 composite significantly outperforming a monolithic PZT of a similar size.
- 16 June 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (6) , 304
Open AccessModeling and Experimental Evaluation of 1-3 Stacked Piezoelectric Transducers for Energy Harvesting
Piezoelectric energy harvesting in roadways can power distributed sensors and electronics by capturing underutilized mechanical energy from traffic. In this research, 1-3 stacked piezocomposites were developed and evaluated to determine optimal designs for multiple applications. The design of these transducers aimed at operating in a multitude of scenarios, under compressive loads (1–10 kN) at low-frequency (10 Hz) applications, intended to simulate vehicular forces. Power comparison was utilized between numerous transducers to determine the most efficient configuration for electromechanical energy conversion. Design guidelines were based on mechanical integrity, output power, active piezoelectric volume percentage, aspect ratio, and geometric factors. The forces applied in this study were reliant on the average vehicle weight. An intermediate PZT volume fraction and moderate pillar aspect ratios were found to yield the highest power output, with the stacked 1-3 composite significantly outperforming a monolithic PZT of a similar size.
- 17 July 2023
- Published by Taylor & Francis in Ferroelectrics
- Vol. 611 (1) , 150-160
Development and evaluation of a fast fabrication process-based 3D printed strain gauge sensors
- 17 July 2023
- Published by Taylor & Francis in Ferroelectrics
- Vol. 611 (1) , 150-160
Development and evaluation of a fast fabrication process-based 3D printed strain gauge sensors
- Open Access
- 15 July 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (7) , 1428
Self-Sustainable IoT-Based Remote Sensing Powered by Energy Harvesting Using Stacked Piezoelectric Transducer and Thermoelectric Generator
We propose a self-powered remote multi-sensing system for traffic sensing which is powered by the collective energy harvested from the mechanical vibration of the road caused by the passing vehicles and from the temperature gradient between the asphalt of the road and the soil underneath. A stacked piezoelectric transducer converts mechanical vibrations into electrical energy and a thermoelectric generator harvests the thermal energy from the thermal gradient. Electrical energy signals from the stacked piezoelectric transducer and the thermoelectric generators are converted into usable DC power to recharge the battery using AC-DC and DC-DC converters working simultaneously. The multi-sensing system comprises an embedded system with a microcontroller that acquires data from the sensors and sends the sensory data to an IoT transceiver which transmits the data as RF packets to an ethernet gateway. The gateway converts the RF packets into Internet Protocol (IP) packets and sends them to a remote server. Laboratory and road-testing results showed over 98% sensory data accuracy with the system functioning solely powered by the energy harvested from the alternative energy sources. The successful maximum transmission distance obtained between the IoT, and the gateway was approximately 1 mile, which is a considerable transmission distance achieved in an urban environment. Successful operation of the self-powered multi-sensing system under both laboratory and road conditions contributes considerably to the fields of energy harvesting and self-powered remote sensing systems. The energy flow chart and efficiency for the steps in the system were found to be mechanical power from vehicles to the energy harvester of 0.25%, stacked PZT transducer efficiency was found to be 37%, and for the TEGs the efficiency is 11%. AC-to-DC and DC-to-DC converters’ efficiencies were found to be 90% and 11%. The wireless communication RF transceiver efficiency was found to be 62.5%.
- 15 July 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (7) , 1428
Open AccessSelf-Sustainable IoT-Based Remote Sensing Powered by Energy Harvesting Using Stacked Piezoelectric Transducer and Thermoelectric Generator
We propose a self-powered remote multi-sensing system for traffic sensing which is powered by the collective energy harvested from the mechanical vibration of the road caused by the passing vehicles and from the temperature gradient between the asphalt of the road and the soil underneath. A stacked piezoelectric transducer converts mechanical vibrations into electrical energy and a thermoelectric generator harvests the thermal energy from the thermal gradient. Electrical energy signals from the stacked piezoelectric transducer and the thermoelectric generators are converted into usable DC power to recharge the battery using AC-DC and DC-DC converters working simultaneously. The multi-sensing system comprises an embedded system with a microcontroller that acquires data from the sensors and sends the sensory data to an IoT transceiver which transmits the data as RF packets to an ethernet gateway. The gateway converts the RF packets into Internet Protocol (IP) packets and sends them to a remote server. Laboratory and road-testing results showed over 98% sensory data accuracy with the system functioning solely powered by the energy harvested from the alternative energy sources. The successful maximum transmission distance obtained between the IoT, and the gateway was approximately 1 mile, which is a considerable transmission distance achieved in an urban environment. Successful operation of the self-powered multi-sensing system under both laboratory and road conditions contributes considerably to the fields of energy harvesting and self-powered remote sensing systems. The energy flow chart and efficiency for the steps in the system were found to be mechanical power from vehicles to the energy harvester of 0.25%, stacked PZT transducer efficiency was found to be 37%, and for the TEGs the efficiency is 11%. AC-to-DC and DC-to-DC converters’ efficiencies were found to be 90% and 11%. The wireless communication RF transceiver efficiency was found to be 62.5%.
- Open Access
- 6 February 2022
- Published by MDPI AG in Journal of Composites Science
- Vol. 6 (2) , 49
Energy Harvesting Using a Stacked PZT Transducer for Self-Sustainable Remote Multi-Sensing and Data Logging System
The work discussed is developing a self-sustainable low-power remote multi-sensing and data logging system for traffic sensing. The system is powered by the energy harvested using a stacked PZT (Lead zirconate titanate) transducer from the mechanical vibration from the vehicles passing over roads. The system is capable of multi-sensing functionality, logging the sensor data, and wirelessly transferring sensory data to an end-user device. Various power management techniques and engineering applications were made to achieve low power operation of the system while maintaining the full functionality and the accuracy of the sensor data. The energy harvester used is a custom-designed and fabricated stacked piezoelectric transducer optimized for maximum energy harvesting from the mechanical vibration from roadway traffic. A custom-built AC to DC converter is used to convert the harvested energy into useable electrical power. The system was tested under various experimental setups yielding satisfactory data accuracy while operating at low power. The system also successfully transferred sensor data remotely. All these features make the system self-sustainable and suitable for remote sensing applications without a conventional power source.
- 6 February 2022
- Published by MDPI AG in Journal of Composites Science
- Vol. 6 (2) , 49
Open AccessEnergy Harvesting Using a Stacked PZT Transducer for Self-Sustainable Remote Multi-Sensing and Data Logging System
The work discussed is developing a self-sustainable low-power remote multi-sensing and data logging system for traffic sensing. The system is powered by the energy harvested using a stacked PZT (Lead zirconate titanate) transducer from the mechanical vibration from the vehicles passing over roads. The system is capable of multi-sensing functionality, logging the sensor data, and wirelessly transferring sensory data to an end-user device. Various power management techniques and engineering applications were made to achieve low power operation of the system while maintaining the full functionality and the accuracy of the sensor data. The energy harvester used is a custom-designed and fabricated stacked piezoelectric transducer optimized for maximum energy harvesting from the mechanical vibration from roadway traffic. A custom-built AC to DC converter is used to convert the harvested energy into useable electrical power. The system was tested under various experimental setups yielding satisfactory data accuracy while operating at low power. The system also successfully transferred sensor data remotely. All these features make the system self-sustainable and suitable for remote sensing applications without a conventional power source.